[PATCH v2 9/9] ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
Gary Bisson
gary.bisson at boundarydevices.com
Tue Sep 8 07:34:46 PDT 2015
Based on an i.MX6 Solo with 512MB DDR3.
http://boundarydevices.com/product/nitrogen6_lite/
Signed-off-by: Gary Bisson <gary.bisson at boundarydevices.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-nit6xlite.dts | 49 +++
arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi | 631 +++++++++++++++++++++++++++++++
3 files changed, 681 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-nit6xlite.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cc29515..b4afb42 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -284,6 +284,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
imx6dl-hummingboard.dtb \
+ imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
imx6dl-phytec-pbab01.dtb \
imx6dl-rex-basic.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-nit6xlite.dts b/arch/arm/boot/dts/imx6dl-nit6xlite.dts
new file mode 100644
index 0000000..e0161e4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-nit6xlite.dts
@@ -0,0 +1,49 @@
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-nit6xlite.dtsi"
+
+/ {
+ model = "Boundary Devices i.MX6 Solo Nitrogen6_Lite Board";
+ compatible = "boundary,imx6dl-nit6xlite", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
new file mode 100644
index 0000000..a3b86ed
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
@@ -0,0 +1,631 @@
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_2p5v: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_wlan_vmmc: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wlan_vmmc>;
+ regulator-name = "reg_wlan_vmmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+ };
+
+ bt_rfkill {
+ compatible = "rfkill-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_bt_rfkill>;
+ gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+ name = "bt_rfkill";
+ type = <2>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ home {
+ label = "Home";
+ gpios = <&gpio7 13 IRQ_TYPE_LEVEL_LOW>;
+ linux,code = <102>;
+ };
+
+ back {
+ label = "Back";
+ gpios = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+ linux,code = <158>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ j14-pin1 {
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ retain-state-suspended;
+ default-state = "off";
+ };
+
+ j14-pin3 {
+ gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ retain-state-suspended;
+ default-state = "off";
+ };
+
+ j14-pins8-9 {
+ gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
+ retain-state-suspended;
+ default-state = "off";
+ };
+
+ j46-pin2 {
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ retain-state-suspended;
+ default-state = "off";
+ };
+
+ j46-pin3 {
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ retain-state-suspended;
+ default-state = "off";
+ };
+ };
+
+ backlight_lcd {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ backlight_lvds0: backlight_lvds0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm4 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_3p3v>;
+ status = "okay";
+ };
+
+ panel_lvds0 {
+ compatible = "hannstar,hsd100pxn1";
+ backlight = <&backlight_lvds0>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx6dl-nit6xlite-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6dl-nit6xlite-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <3>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: m25p80 at 0 {
+ compatible = "microchip,sst25vf016b";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ txen-skew-ps = <0>;
+ txc-skew-ps = <3000>;
+ rxdv-skew-ps = <0>;
+ rxc-skew-ps = <3000>;
+ rxd0-skew-ps = <0>;
+ rxd1-skew-ps = <0>;
+ rxd2-skew-ps = <0>;
+ rxd3-skew-ps = <0>;
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: sgtl5000 at 0a {
+ compatible = "fsl,sgtl5000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sgtl5000>;
+ reg = <0x0a>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_2p5v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ egalax_ts at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+
+ ft5x06_ts at 38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+
+ isl1208 at 6f {
+ compatible = "isil,isl1208";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ reg = <0x6f>;
+ interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_j10>;
+ pinctrl-1 = <&pinctrl_j28>;
+
+ imx6dl-nit6xlite {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_bt_rfkill: bt_rfkillgrp {
+ fsl,pins = <
+ /* BT wake */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ /* BT reset */
+ MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0b0b0
+ /* BT reg en */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+ /* BT host wake irq */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x100b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ /* Phy reset */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x0f0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ /* Home Button: J14 pin 5 */
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0
+ /* Back Button: J14 pin 7 */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ /* Touch IRQ: J7 pin 4 */
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ /* tcs2004 IRQ */
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1b0b0
+ /* tsc2004 reset */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x0b0b0
+ >;
+ };
+
+ pinctrl_j10: j10grp {
+ fsl,pins = <
+ /* Broadcom WiFi module pins */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+ MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0
+ MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x000b0
+ >;
+ };
+
+ pinctrl_j28: j28grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0b0b0
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x0b0b0
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x030b0
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x0b0b0
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_wlan_vmmc: wlan_vmmcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x030b0
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1b0b0
+ >;
+ };
+
+ pinctrl_sgtl5000: sgtl5000grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000b0
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ /* power enable, high active */
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ >;
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel at 0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <4>;
+ non-removable;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_wlan_vmmc>;
+ vqmmc-1-8-v;
+ ocr-limit = <0x180>; /* 1.65v - 2.1v */
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
--
2.5.1
More information about the linux-arm-kernel
mailing list