[PATCH-v2 4/7] mmc: sdhci-pxav3: Add pinctl setting according to bus clock
Jisheng Zhang
jszhang at marvell.com
Tue Sep 8 03:04:51 PDT 2015
On Tue, 8 Sep 2015 15:32:34 +0530
Vaibhav Hiremath <vaibhav.hiremath at linaro.org> wrote:
>
>
> On Tuesday 08 September 2015 03:22 PM, Jisheng Zhang wrote:
> > On Tue, 8 Sep 2015 15:04:41 +0530
> > Vaibhav Hiremath <vaibhav.hiremath at linaro.org> wrote:
> >
> >>
> >>
> >> On Tuesday 08 September 2015 12:22 PM, Jisheng Zhang wrote:
> >>> On Mon, 7 Sep 2015 16:48:38 +0530
> >>> Vaibhav Hiremath <vaibhav.hiremath at linaro.org> wrote:
> >>>
> >>>> Different bus clock may need different pin setting.
> >>>> For example, fast bus clock like 208Mhz need pin drive fast
> >>>> while slow bus clock prefer pin drive slow to guarantee
> >>>> signal quality.
> >>>>
> >>>> So this patch creates two states,
> >>>> - Default (slow/normal) pin state
> >>>> - And fast pin state for higher freq bus speed.
> >>>>
> >>>> And selection of pin state is done based on timing mode.
> >>>>
> >>>> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath at linaro.org>
> >>>> Signed-off-by: Kevin Liu <kliu5 at marvell.com>
> >>>> ---
> >>>> drivers/mmc/host/sdhci-pxav3.c | 45 +++++++++++++++++++++++++++++++++++++++++-
> >>>> 1 file changed, 44 insertions(+), 1 deletion(-)
> >>>>
> >>>> diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c
> >>>> index c2b2b78..d933f75 100644
> >>>> --- a/drivers/mmc/host/sdhci-pxav3.c
> >>>> +++ b/drivers/mmc/host/sdhci-pxav3.c
> >>>> @@ -35,6 +35,7 @@
> >>>> #include <linux/pm.h>
> >>>> #include <linux/pm_runtime.h>
> >>>> #include <linux/mbus.h>
> >>>> +#include <linux/pinctrl/consumer.h>
> >>>>
> >>>> #include "sdhci.h"
> >>>> #include "sdhci-pltfm.h"
> >>>> @@ -92,6 +93,10 @@ struct sdhci_pxa {
> >>>> void __iomem *io_pwr_reg;
> >>>> void __iomem *io_pwr_lock_reg;
> >>>> struct sdhci_pxa_data *data;
> >>>> +
> >>>> + struct pinctrl *pinctrl;
> >>>> + struct pinctrl_state *pins_default;
> >>>> + struct pinctrl_state *pins_fast;
> >>>> };
> >>>>
> >>>> static struct sdhci_pxa_data pxav3_data_v1 = {
> >>>> @@ -298,6 +303,33 @@ static void pxav3_gen_init_74_clocks(struct sdhci_host *host, u8 power_mode)
> >>>> pxa->power_mode = power_mode;
> >>>> }
> >>>>
> >>>> +static int pxav3_select_pinstate(struct sdhci_host *host, unsigned int uhs)
> >>>> +{
> >>>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> >>>> + struct sdhci_pxa *pxa = pltfm_host->priv;
> >>>> + struct pinctrl_state *pinctrl;
> >>>> +
> >>>> + if (IS_ERR(pxa->pinctrl) ||
> >>>> + IS_ERR(pxa->pins_default) ||
> >>>> + IS_ERR(pxa->pins_fast))
> >>>> + return -EINVAL;
> >>>> +
> >>>> + switch (uhs) {
> >>>> + case MMC_TIMING_UHS_SDR50:
> >>>> + case MMC_TIMING_UHS_SDR104:
> >>>> + case MMC_TIMING_MMC_HS200:
> >>>> + case MMC_TIMING_MMC_HS400:
> >>>> + pinctrl = pxa->pins_fast;
> >>>> + break;
> >>>> + default:
> >>>> + /* back to default state for other legacy timing */
> >>>> + pinctrl = pxa->pins_default;
> >>>> + break;
> >>>> + }
> >>>> +
> >>>> + return pinctrl_select_state(pxa->pinctrl, pinctrl);
> >>>> +}
> >>>> +
> >>>> static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> >>>> {
> >>>> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> >>>> @@ -353,6 +385,8 @@ static void pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> >>>> dev_dbg(mmc_dev(host->mmc),
> >>>> "%s uhs = %d, ctrl_2 = %04X\n",
> >>>> __func__, uhs, ctrl_2);
> >>>> +
> >>>> + pxav3_select_pinstate(host, uhs);
> >>>
> >>> return pxav3_select_pinstate(host, uhs);?
> >>>
> >>
> >> Its void function, so don't need it.
> >
> > Can you please have a look at the function?
> >
> > static int pxav3_select_pinstate(struct sdhci_host *host, unsigned int uhs)
> >
>
> I was referring to pxav3_set_uhs_signaling().
> It is void, so what you are suggesting would generate warning.
Oops, you are correct.
>
> >>
> >>> And could we ignore this call for those SDHCI hosts that don't need it?
> >>>
> >>
> >> I do not want to introduce flags here.
> >> And also, it is already ignored for those who don't need it.
> >>
> >> The first thing in the function pxav3_select_pinstate() is
> >>
> >>
> >> if (IS_ERR(pxa->pinctrl) ||
> >> IS_ERR(pxa->pins_default) ||
> >> IS_ERR(pxa->pins_fast))
> >> return -EINVAL;
> >>
> >>
> >> So its already handled.
> >>
> >>>> }
> >>>>
> >>>> static void pxav3_voltage_switch(struct sdhci_host *host,
> >>>> @@ -416,7 +450,6 @@ static void pxav3_set_clock(struct sdhci_host *host, unsigned int clock)
> >>>> /* TX internal clock selection */
> >>>> pxav3_set_tx_clock(host);
> >>>> }
> >>>> -
> >>>
> >>> why not fix this in patch 3?
> >>>
> >>
> >> Oops. it got missed from my eyes :)
> >> Will fix in next version.
> >>
> >>>> }
> >>>>
> >>>> static const struct sdhci_ops pxav3_sdhci_ops = {
> >>>> @@ -586,6 +619,16 @@ static int sdhci_pxav3_probe(struct platform_device *pdev)
> >>>> }
> >>>> }
> >>>>
> >>>> + pxa->pinctrl = devm_pinctrl_get(dev);
> >>>
> >>> could we ignore this for those SDHCI hosts that don't need it?
> >>>
> >>
> >> Again, no need to introduce flags here. This is standard call and
> >> handled properly. So for the platforms not using this, it really should
> >> not matter.
> >> Also, lookup is getting executed only when pinctrl is populated.
> >>
> >> So I do not see any need here.
> >>
> >>>> + if (!IS_ERR(pxa->pinctrl)) {
> >>>> + pxa->pins_default = pinctrl_lookup_state(pxa->pinctrl, "default");
> >>>> + if (IS_ERR(pxa->pins_default))
> >>>> + dev_err(dev, "could not get default pinstate\n");
> >>>
> >>> Why those SDHCI hosts that don't need pinctl setting should got this error?
> >>>
> >>
> >> It won't.
> >
> > It does. On Marvell Berlin SoCs, I got
> >
> > [ 1.070000] sdhci-pxav3 f7ab0800.sdhci: could not get default pinstate
> > [ 1.080000] sdhci-pxav3 f7ab0800.sdhci: could not get fast pinstate
> >
> >
> >
> >>
> >> If Host does not need pinctrl, the execution would never reach this
> >> point.
> >> The if condition check would handle it, isn't it?
> >>
> >> pxa->pinctrl = devm_pinctrl_get(dev);
> >
> > It seems this function always succeed...
> >
>
> Not always.
> I would succeed only if you have pinctrl defined in DT for this device.
Yes, that's what I thought, but I got
[ 1.070000] sdhci-pxav3 f7ab0800.sdhci: could not get default pinstate
[ 1.080000] sdhci-pxav3 f7ab0800.sdhci: could not get fast pinstate
there's no pinctrl for f7ab0800.sdhci. Am I missing somthing?
Thanks,
Jisheng
>
> And if you have pinctrl defined, isn't it is expected to have "default"
> pin state to be always present?
> And if answer is yes here, then it is fair to be prompting error for it.
>
> > From another side, we may have default pin in dts, for example: pin muxed between
> > emmc and nandflash. But we don't have fast pinstate, so we at least need the
> > flag to fast pinstate. Otherwise, in such platforms, we could get something like
> >
>
> That is exactly the reason behind keeping it as dev_info.
>
> > [ 1.000000] sdhci-pxav3 f7ab0000.sdhci: get default pinstate
> > [ 1.000000] sdhci-pxav3 f7ab0000.sdhci: could not get fast pinstate
> >
> >
> Thanks,
> Vaibhav
More information about the linux-arm-kernel
mailing list