[PATCH 1/2] arm/arm64: KVM: vgic: Move active state handling to flush_hwstate

[Eric Auger]

Hi,
On 09/04/2015 04:24 PM, Christoffer Dall wrote:
> We currently set the physical active state only when we *inject* a new
> pending virtual interrupt, but this is actually not correct, because we
> could have been preempted and run something else on the system that
> resets the active state to clear.  This causes us to run the VM with the
> timer set to fire, but without setting the physical active state.
> 
> The solution is to always check the LR configurations, and we if have a
> mapped interrupt in the LR in either the pending or active state
> (virtual), then set the physical active state.
> 
> Acked-by: Marc Zyngier <marc.zyngier at arm.com>
> Signed-off-by: Christoffer Dall <christoffer.dall at linaro.org>
> ---
>  virt/kvm/arm/vgic.c | 42 ++++++++++++++++++++++++++----------------
>  1 file changed, 26 insertions(+), 16 deletions(-)
> 
> diff --git a/virt/kvm/arm/vgic.c b/virt/kvm/arm/vgic.c
> index 9eb489a..6bd1c9b 100644
> --- a/virt/kvm/arm/vgic.c
> +++ b/virt/kvm/arm/vgic.c
> @@ -1144,26 +1144,11 @@ static void vgic_queue_irq_to_lr(struct kvm_vcpu *vcpu, int irq,
>  		struct irq_phys_map *map;
>  		map = vgic_irq_map_search(vcpu, irq);
>  
> -		/*
> -		 * If we have a mapping, and the virtual interrupt is
> -		 * being injected, then we must set the state to
> -		 * active in the physical world. Otherwise the
> -		 * physical interrupt will fire and the guest will
> -		 * exit before processing the virtual interrupt.
> -		 */
>  		if (map) {
> -			int ret;
> -
> -			BUG_ON(!map->active);
I have a question about this map->active. I did not find any user of
kvm_vgic_set_phys_irq_active anymore. The flag is directly updated in
vgic_sync_hwirq through the irq_get_irqchip_state query. In the same
function, before there is a "BUG_ON(!map || !map->active);"

Can't we have this BUG_ON firing?


>  			vlr.hwirq = map->phys_irq;
>  			vlr.state |= LR_HW;
>  			vlr.state &= ~LR_EOI_INT;
>  
> -			ret = irq_set_irqchip_state(map->irq,
> -						    IRQCHIP_STATE_ACTIVE,
> -						    true);
> -			WARN_ON(ret);
> -
>  			/*
>  			 * Make sure we're not going to sample this
>  			 * again, as a HW-backed interrupt cannot be
> @@ -1255,7 +1240,7 @@ static void __kvm_vgic_flush_hwstate(struct kvm_vcpu *vcpu)
>  	struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
>  	struct vgic_dist *dist = &vcpu->kvm->arch.vgic;
>  	unsigned long *pa_percpu, *pa_shared;
> -	int i, vcpu_id;
> +	int i, vcpu_id, lr, ret;
>  	int overflow = 0;
>  	int nr_shared = vgic_nr_shared_irqs(dist);
>  
> @@ -1310,6 +1295,31 @@ epilog:
>  		 */
>  		clear_bit(vcpu_id, dist->irq_pending_on_cpu);
>  	}
> +
> +	for (lr = 0; lr < vgic->nr_lr; lr++) {
> +		struct vgic_lr vlr;
> +
> +		if (!test_bit(lr, vgic_cpu->lr_used))
> +			continue;
> +
> +		vlr = vgic_get_lr(vcpu, lr);
> +
> +		/*
> +		 * If we have a mapping, and the virtual interrupt is
> +		 * presented to the guest (as pending or active), then we must
> +		 * set the state to active in the physical world. See
> +		 * Documentation/virtual/kvm/arm/vgic-mapped-irqs.txt.
if upstreamed in 4.3 whereas the other series is not there,
vgic-mapped-irqs.txt won't be available.
> +		 */
> +		if (vlr.state & LR_HW) {
> +			struct irq_phys_map *map;
> +			map = vgic_irq_map_search(vcpu, vlr.irq);
> +
> +			ret = irq_set_irqchip_state(map->irq,
> +						    IRQCHIP_STATE_ACTIVE,
> +						    true);
I understand the need for manually setting the phys dist state in case
of timer however for non shared IRQs, GIC does the job directly. But I
guess it does not harm.

Eric
> +			WARN_ON(ret);
> +		}
> +	}
>  }
>  
>  static bool vgic_process_maintenance(struct kvm_vcpu *vcpu)
>