[PATCH 2/2] arm64: dts: add dts files for Hisilicon Hip05-D02 Development Board
Ding Tianhong
dingtianhong at huawei.com
Wed Sep 2 01:20:36 PDT 2015
On 2015/9/2 15:58, Marc Zyngier wrote:
> [Don't top-post, this is very annoying]
>
> On 02/09/15 05:28, Ding Tianhong wrote:
>> Hi，Marc：
>>
>> Can you check this, I am not sure whether the GIC_CPU_MASK_SIMPLE(xx)
>> is used for gic-v3, maybe we should remove it, thanks.
>
> The binding documentation
> (Documentation/devicetree/bindings/arm/gic-v3.txt) is very clear:
>
> The 3rd cell is the flags, encoded as follows:
> bits[3:0] trigger type and level flags.
> 1 = edge triggered
> 4 = level triggered
>
> There is no mask whatsoever, because that would restrict the interrupt
> to only 32 CPUs at most.
>
> So please remove this, this is just wrong.
>
> Thanks,
>
> M.
>
Ok, thanks.
Ding
>> Ding
>>
>> On 2015/8/31 21:44, Ding Tianhong wrote:
>>> On 2015/8/31 21:12, Leo Yan wrote:
>>>> On Sat, Aug 29, 2015 at 04:52:41PM +0800, Ding Tianhong wrote:
>>>>> Add initial dtsi file to support Hisilicon Hip05-D02 Board with
>>>>> support of CPUs in four clusters and each cluster has quard Cortex-A57.
>>>>>
>>>>> Also add dts file to support Hip05-D02 development board.
>>>>>
>>>>> Signed-off-by: Ding Tianhong <dingtianhong at huawei.com>
>>>>> Signed-off-by: Kefeng Wang <wangkefeng.wang at huawei.com>
>>>>> ---
>>>>> arch/arm64/boot/dts/hisilicon/Makefile | 2 +-
>>>>> arch/arm64/boot/dts/hisilicon/hip05-d02.dts | 36 ++++
>>>>> arch/arm64/boot/dts/hisilicon/hip05.dtsi | 271 ++++++++++++++++++++++++++++
>>>>> 3 files changed, 308 insertions(+), 1 deletion(-)
>>>>> create mode 100644 arch/arm64/boot/dts/hisilicon/hip05-d02.dts
>>>>> create mode 100644 arch/arm64/boot/dts/hisilicon/hip05.dtsi
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/hisilicon/Makefile b/arch/arm64/boot/dts/hisilicon/Makefile
>>>>> index fa81a6e..cd158b8 100644
>>>>> --- a/arch/arm64/boot/dts/hisilicon/Makefile
>>>>> +++ b/arch/arm64/boot/dts/hisilicon/Makefile
>>>>> @@ -1,4 +1,4 @@
>>>>> -dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb
>>>>> +dtb-$(CONFIG_ARCH_HISI) += hi6220-hikey.dtb hip05-d02.dtb
>>>>>
>>>>> always := $(dtb-y)
>>>>> subdir-y := $(dts-dirs)
>>>>> diff --git a/arch/arm64/boot/dts/hisilicon/hip05-d02.dts b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts
>>>>> new file mode 100644
>>>>> index 0000000..ae34e25
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts
>>>>> @@ -0,0 +1,36 @@
>>>>> +/**
>>>>> + * dts file for Hisilicon D02 Development Board
>>>>> + *
>>>>> + * Copyright (C) 2014,2015 Hisilicon Ltd.
>>>>> + *
>>>>> + * This program is free software; you can redistribute it and/or modify
>>>>> + * it under the terms of the GNU General Public License version 2 as
>>>>> + * publishhed by the Free Software Foundation.
>>>>> + *
>>>>> + */
>>>>> +
>>>>> +/dts-v1/;
>>>>> +
>>>>> +#include "hip05.dtsi"
>>>>> +
>>>>> +/ {
>>>>> + model = "Hisilicon Hip05 D02 Development Board";
>>>>> + compatible = "hisilicon,hip05-d02";
>>>>> +
>>>>> + memory at 00000000 {
>>>>> + device_type = "memory";
>>>>> + reg = <0x0 0x00000000 0x0 0x80000000>;
>>>>> + };
>>>>> +
>>>>> + aliases {
>>>>> + serial0 = &uart0;
>>>>> + };
>>>>> +
>>>>> + chosen {
>>>>> + stdout-path = "serial0:115200n8";
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&uart0 {
>>>>> + status = "ok";
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi
>>>>> new file mode 100644
>>>>> index 0000000..da12d94
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi
>>>>> @@ -0,0 +1,271 @@
>>>>> +/**
>>>>> + * dts file for Hisilicon D02 Development Board
>>>>> + *
>>>>> + * Copyright (C) 2014,2015 Hisilicon Ltd.
>>>>> + *
>>>>> + * This program is free software; you can redistribute it and/or modify
>>>>> + * it under the terms of the GNU General Public License version 2 as
>>>>> + * publishhed by the Free Software Foundation.
>>>>> + *
>>>>> + */
>>>>> +
>>>>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>> +
>>>>> +/ {
>>>>> + compatible = "hisilicon,hip05-d02";
>>>>> + interrupt-parent = <&gic>;
>>>>> + #address-cells = <2>;
>>>>> + #size-cells = <2>;
>>>>> +
>>>>> + psci {
>>>>> + compatible = "arm,psci-0.2";
>>>>> + method = "smc";
>>>>> + };
>>>>> +
>>>>> + cpus {
>>>>> + #address-cells = <1>;
>>>>> + #size-cells = <0>;
>>>>> +
>>>>> + cpu-map {
>>>>> + cluster0 {
>>>>> + core0 {
>>>>> + cpu = <&cpu0>;
>>>>> + };
>>>>> + core1 {
>>>>> + cpu = <&cpu1>;
>>>>> + };
>>>>> + core2 {
>>>>> + cpu = <&cpu2>;
>>>>> + };
>>>>> + core3 {
>>>>> + cpu = <&cpu3>;
>>>>> + };
>>>>> + };
>>>>> + cluster1 {
>>>>> + core0 {
>>>>> + cpu = <&cpu4>;
>>>>> + };
>>>>> + core1 {
>>>>> + cpu = <&cpu5>;
>>>>> + };
>>>>> + core2 {
>>>>> + cpu = <&cpu6>;
>>>>> + };
>>>>> + core3 {
>>>>> + cpu = <&cpu7>;
>>>>> + };
>>>>> + };
>>>>> + cluster2 {
>>>>> + core0 {
>>>>> + cpu = <&cpu8>;
>>>>> + };
>>>>> + core1 {
>>>>> + cpu = <&cpu9>;
>>>>> + };
>>>>> + core2 {
>>>>> + cpu = <&cpu10>;
>>>>> + };
>>>>> + core3 {
>>>>> + cpu = <&cpu11>;
>>>>> + };
>>>>> + };
>>>>> + cluster3 {
>>>>> + core0 {
>>>>> + cpu = <&cpu12>;
>>>>> + };
>>>>> + core1 {
>>>>> + cpu = <&cpu13>;
>>>>> + };
>>>>> + core2 {
>>>>> + cpu = <&cpu14>;
>>>>> + };
>>>>> + core3 {
>>>>> + cpu = <&cpu15>;
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + cpu0: cpu at 20000 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>
>>>> Change to "arm,cortex-a57","arm,armv8"?
>>>>
>>>
>>> Ok，but I think should be "hisilicon,hip05","arm,armv8".
>>>
>>>>> + reg = <0x20000>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu1: cpu at 20001 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20001>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu2: cpu at 20002 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20002>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu3: cpu at 20003 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20003>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu4: cpu at 20100 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20100>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu5: cpu at 20101 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20101>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu6: cpu at 20102 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20102>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu7: cpu at 20103 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20103>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu8: cpu at 20200 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20200>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu9: cpu at 20201 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20201>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu10: cpu at 20202 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20202>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu11: cpu at 20203 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20203>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu12: cpu at 20300 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20300>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu13: cpu at 20301 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20301>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu14: cpu at 20302 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20302>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> +
>>>>> + cpu15: cpu at 20303 {
>>>>> + device_type = "cpu";
>>>>> + compatible = "arm,armv8";
>>>>> + reg = <0x20303>;
>>>>> + enable-method = "psci";
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + gic: interrupt-controller at 8d000000 {
>>>>> + compatible = "arm,gic-v3";
>>>>> + #interrupt-cells = <3>;
>>>>> + #address-cells = <2>;
>>>>> + #size-cells = <2>;
>>>>> + ranges;
>>>>> + interrupt-controller;
>>>>> + #redistributor-regions = <1>;
>>>>> + redistributor-stride = <0x0 0x30000>;
>>>>> + reg = <0x0 0x8d000000 0 0x10000>, /* GICD */
>>>>> + <0x0 0x8d100000 0 0x300000>, /* GICR */
>>>>> + <0x0 0xfe000000 0 0x10000>, /* GICC */
>>>>> + <0x0 0xfe010000 0 0x10000>, /* GICH */
>>>>> + <0x0 0xfe020000 0 0x10000>; /* GICV */
>>>>> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
>>>>> +
>>>>> + its_totems: interrupt-controller at 8c000000 {
>>>>> + compatible = "arm,gic-v3-its";
>>>>> + msi-controller;
>>>>> + reg = <0x0 0x8c000000 0x0 0x1000000>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + timer {
>>>>> + compatible = "arm,armv8-timer";
>>>>> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
>>>>> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
>>>>
>>>> Here have a question:
>>>> In devcie tree binding file: Documentation/devicetree/bindings/arm/gic.txt,
>>>> it only considers for maximum 8 cpus. So will we need change the
>>>> binding file and also use GIC_CPU_MASK_SIMPLE(16) for 16 cores?
>>>>
>>>
>>> Looks like should updtate gic.txt and use the GIC_CPU_MASK_SIMPLE(16) for 16 cores.
>>>
>>> Ding
>>>
>>>>> + };
>>>>> +
>>>>> + pmu {
>>>>> + compatible = "arm,armv8-pmuv3";
>>>>> + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
>>>>> + };
>>>>> +
>>>>> + soc {
>>>>> + compatible = "simple-bus";
>>>>> + #address-cells = <2>;
>>>>> + #size-cells = <2>;
>>>>> + ranges;
>>>>> +
>>>>> + refclk200mhz: refclk200mhz {
>>>>> + compatible = "fixed-clock";
>>>>> + #clock-cells = <0>;
>>>>> + clock-frequency = <200000000>;
>>>>> + };
>>>>> +
>>>>> + uart0: uart at 80300000 {
>>>>> + compatible = "snps,dw-apb-uart";
>>>>> + reg = <0x0 0x80300000 0x0 0x10000>;
>>>>> + interrupts = <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>;
>>>>> + clocks = <&refclk200mhz>;
>>>>> + clock-names = "apb_pclk";
>>>>> + reg-shift = <2>;
>>>>> + reg-io-width = <4>;
>>>>> + status = "disabled";
>>>>> + };
>>>>> +
>>>>> + uart1: uart at 80310000 {
>>>>> + compatible = "snps,dw-apb-uart";
>>>>> + reg = <0x0 0x80310000 0x0 0x10000>;
>>>>> + interrupts = <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>;
>>>>> + clocks = <&refclk200mhz>;
>>>>> + clock-names = "apb_pclk";
>>>>> + reg-shift = <2>;
>>>>> + reg-io-width = <4>;
>>>>> + status = "disabled";
>>>>> + };
>>>>> + };
>>>>> +};
>>>>> --
>>>>> 1.9.0
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> linux-arm-kernel mailing list
>>>>> linux-arm-kernel at lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>>>
>>>> .
>>>>
>>>
>>>
>>> _______________________________________________
>>> linuxarm mailing list
>>> linuxarm at huawei.com
>>> http://rnd-openeuler.huawei.com/mailman/listinfo/linuxarm
>>>
>>
>>
>
>
More information about the linux-arm-kernel
mailing list