[PATCHv7 1/3] ARM: dts: Add Altera L2 Cache and OCRAM EDAC entries

[dinguyen at opensource.altera.com]

From: Thor Thayer <tthayer at opensource.altera.com>

Adding the device tree entries and bindings needed to support
the Altera L2 cache and On-Chip RAM EDAC. This patch relies upon
an earlier patch to declare and setup On-chip RAM properly.
http://www.spinics.net/lists/devicetree/msg51117.html

Signed-off-by: Thor Thayer <tthayer at opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen at opensource.altera.com>
---
v7: No Change
v6: Change to nested EDAC device nodes based on community
    feedback. Remove L2 syscon. Use consolidated binding.
v3-5: No Change
v2: Remove OCRAM declaration and reference prior patch.
---
 .../bindings/arm/altera/socfpga-edac.txt           | 46 ++++++++++++++++++++++
 arch/arm/boot/dts/socfpga.dtsi                     | 20 ++++++++++
 2 files changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt

diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt
new file mode 100644
index 0000000..4bf32e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/altera/socfpga-edac.txt
@@ -0,0 +1,46 @@
+Altera SoCFPGA Error Detection and Correction [EDAC]
+
+Required Properties:
+- compatible : Should be "altr,edac"
+- #address-cells: must be 1
+- #size-cells: must be 1
+- ranges : standard definition, should translate from local addresses
+
+Subcomponents:
+
+L2 Cache ECC
+Required Properties:
+- compatible : Should be "altr,l2-edac"
+- reg : Address and size for ECC error interrupt clear registers.
+- interrupts : Should be single bit error interrupt, then double bit error
+	interrupt. Note the rising edge type.
+
+On Chip RAM ECC
+Required Properties:
+- compatible : Should be "altr,ocram-edac"
+- reg : Address and size for ECC error interrupt clear registers.
+- iram : phandle to On-Chip RAM definition.
+- interrupts : Should be single bit error interrupt, then double bit error
+	interrupt. Note the rising edge type.
+
+Example:
+
+	soc_ecc {
+		compatible = "altr,edac";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		l2edac at ffd08140 {
+			compatible = "altr,l2-edac";
+			reg = <0xffd08140 0x4>;
+			interrupts = <0 36 1>, <0 37 1>;
+		};
+
+		ocramedac at ffd08144 {
+			compatible = "altr,ocram-edac";
+			reg = <0xffd08144 0x4>;
+			iram = <&ocram>;
+			interrupts = <0 178 1>, <0 179 1>;
+		};
+	};
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index 314e589..7cfec22 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -660,6 +660,26 @@
 			interrupts = <0 39 4>;
 		};
 
+		soc_ecc {
+			compatible = "altr,edac";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			l2edac at ffd08140 {
+				compatible = "altr,l2-edac";
+				reg = <0xffd08140 0x4>;
+				interrupts = <0 36 1>, <0 37 1>;
+			};
+
+			ocramedac at ffd08144 {
+				compatible = "altr,ocram-edac";
+				reg = <0xffd08144 0x4>;
+				iram = <&ocram>;
+				interrupts = <0 178 1>, <0 179 1>;
+			};
+		};
+
 		L2: l2-cache at fffef000 {
 			compatible = "arm,pl310-cache";
 			reg = <0xfffef000 0x1000>;
-- 
2.4.5