[PATCH 1/1] doc/bindings: Update Layerscape PCIe devicetree bindings for LS2080A

[Bhupesh Sharma]

Update the definition of the Layerscape PCI compatible string to add
support for LS2080A, as the controller on LS2080A is different from
LS1021A SoC.

While at it, move the clock related properties in the Designware PCIe
controller bindings to 'optional' set of properties.

Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Acked-by: Arnd Bergmann <arnd at arndb.de>
---
Hi Bjorn,

As discussed with Arnd (http://www.spinics.net/lists/linux-clk/msg04092.html),
this patch depends on a patch that is in your PCI tree but not yet in mainline.

So, sending this to you, so that you can apply the patch on top of the other
one.

 .../devicetree/bindings/pci/designware-pcie.txt    |   10 +++++-----
 .../devicetree/bindings/pci/layerscape-pci.txt     |   14 ++++++++++++--
 2 files changed, 17 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index 0036ab3..576218a 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -14,11 +14,6 @@ Required properties:
 - interrupt-map-mask and interrupt-map: standard PCI properties
 	to define the mapping of the PCIe interface to interrupt
 	numbers.
-- clocks: Must contain an entry for each entry in clock-names.
-	See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
-	- "pcie"
-	- "pcie_bus"
 
 Optional properties:
 - num-lanes: number of lanes to use (this property should be specified unless
@@ -27,3 +22,8 @@ Optional properties:
 - bus-range: PCI bus numbers covered (it is recommended for new devicetrees to
   specify this property, to keep backwards compatibility a range of 0x00-0xff
   is assumed if not present)
+- clocks: Must contain an entry for each entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+	- "pcie"
+	- "pcie_bus"
diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt
index 6286f04..ac7e07e 100644
--- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt
+++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt
@@ -1,10 +1,20 @@
 Freescale Layerscape PCIe controller
 
-This PCIe host controller is based on the Synopsis Designware PCIe IP
+This PCIe host controller is based on the Synopsys Designware PCIe IP
 and thus inherits all the common properties defined in designware-pcie.txt.
 
+This controller derives its clocks from the Reset Configuration Word (RCW)
+which is used to describe the PLL settings at the time of chip-reset.
+
+Also as per the available Reference Manuals, there is no specific 'version'
+register available in the Freescale PCIe controller register set,
+which can allow determining the underlying Designware PCIe controller version
+information.
+
 Required properties:
-- compatible: should contain the platform identifier such as "fsl,ls1021a-pcie"
+- compatible: should contain the platform identifier such as:
+        "fsl,ls1021a-pcie", "snps,dw-pcie"
+        "fsl,ls2080a-pcie", "snps,dw-pcie"
 - reg: base addresses and lengths of the PCIe controller
 - interrupts: A list of interrupt outputs of the controller. Must contain an
   entry for each entry in the interrupt-names property.
-- 
1.7.9.5