MUSB peripheral DMA regression caused by driver core runtime PM change
Felipe Balbi
balbi at ti.com
Fri Oct 23 09:48:33 PDT 2015
Hi,
Tony Lindgren <tony at atomide.com> writes:
> From: Tony Lindgren <tony at atomide.com>
> Date: Fri, 23 Oct 2015 09:03:22 -0700
> Subject: [PATCH] usb: musb: omap2430: Fix regression caused by driver core
> change
>
> Commit ddef08dd00f5 ("Driver core: wakeup the parent device before trying
> probe") started automatically ensuring the parent device is enabled when
> the child gets probed.
>
> This however caused a regression for MUSB omap2430 interface as the
> runtime PM for the parent device needs the child initialized to access
> the MUSB hardware registers.
>
> Let's delay the enabling of PM runtime for the parent until the child
> has been properly initialized as suggested in an earlier patch by
> Grygorii Strashko <grygorii.strashko at ti.com>.
>
> In addition to delaying pm_runtime_enable, we now also need to make sure
> the parent is enabled during omap2430_musb_init. We also want to propagate
> an error from omap2430_runtime_resume if struct musb is not initialized.
>
> Note that we use pm_runtime_put_noidle here for both the child and parent
> to prevent an extra runtime_suspend/resume cycle.
>
> Let's also add some comments to avoid confusion between the
> two different devices.
>
> Fixes: ddef08dd00f5 ("Driver core: wakeup the parent device before
> trying probe")
> Suggested-by: Grygorii Strashko <grygorii.strashko at ti.com>
> Signed-off-by: Tony Lindgren <tony at atomide.com>
I'm fine with this patch to fix this v4.3 regression. Greg, do you want
a pull request or can you take this in as a patch ? In any case:
Acked-by: Felipe Balbi <balbi at ti.com>
> --- a/drivers/usb/musb/omap2430.c
> +++ b/drivers/usb/musb/omap2430.c
> @@ -391,9 +391,20 @@ static int omap2430_musb_init(struct musb *musb)
> }
> musb->isr = omap2430_musb_interrupt;
>
> + /*
> + * Enable runtime PM for musb parent (this driver). We can't
> + * do it earlier as struct musb is not yet allocated and we
> + * need to touch the musb registers for runtime PM.
> + */
> + pm_runtime_enable(glue->dev);
> + status = pm_runtime_get_sync(glue->dev);
> + if (status < 0)
> + goto err1;
> +
> status = pm_runtime_get_sync(dev);
> if (status < 0) {
> dev_err(dev, "pm_runtime_get_sync FAILED %d\n", status);
> + pm_runtime_put_sync(glue->dev);
> goto err1;
> }
>
> @@ -426,6 +437,7 @@ static int omap2430_musb_init(struct musb *musb)
> phy_power_on(musb->phy);
>
> pm_runtime_put_noidle(musb->controller);
> + pm_runtime_put_noidle(glue->dev);
> return 0;
>
> err1:
> @@ -626,7 +638,11 @@ static int omap2430_probe(struct platform_device *pdev)
> goto err2;
> }
>
> - pm_runtime_enable(&pdev->dev);
> + /*
> + * Note that we cannot enable PM runtime yet for this
> + * driver as we need struct musb initialized first.
> + * See omap2430_musb_init above.
> + */
>
> ret = platform_device_add(musb);
> if (ret) {
> @@ -675,11 +691,12 @@ static int omap2430_runtime_resume(struct device *dev)
> struct omap2430_glue *glue = dev_get_drvdata(dev);
> struct musb *musb = glue_to_musb(glue);
>
> - if (musb) {
> - omap2430_low_level_init(musb);
> - musb_writel(musb->mregs, OTG_INTERFSEL,
> - musb->context.otg_interfsel);
> - }
> + if (!musb)
> + return -EPROBE_DEFER;
> +
> + omap2430_low_level_init(musb);
> + musb_writel(musb->mregs, OTG_INTERFSEL,
> + musb->context.otg_interfsel);
>
> return 0;
> }
--
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 818 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151023/5c5b57fb/attachment.sig>
More information about the linux-arm-kernel
mailing list