[PATCH v4 1/3] dt-bindings: rockchip-thermal: Add the pinctrl states in this document
Rob Herring
robh+dt at kernel.org
Fri Oct 23 06:29:23 PDT 2015
On Fri, Oct 23, 2015 at 6:25 AM, Caesar Wang <wxt at rock-chips.com> wrote:
> The "init" pinctrl is defined we'll set
> pinctrl to this state before probe and then "default" after probe.
> Add the "init" and "sleep" pinctrl as the OTP gpio state, since we need
> switch the pin to gpio state before the TSADC controller is reset.
>
> AFAIK, the TSADC controller is reset, the tshut polarity will be
> a *low* signal in a short period of time for some devices.
>
> Says:
> The TSADC get the temperature on rockchip thermal.
>
> If T(current temperature) < (setting temperature), the OTP output the
> *high* signal.
> If T(current temperature) > (setting temperature), the OTP output the
> *low* Signal.
>
> In some cases, the OTP pin is connected to the PMIC, maybe the
> PMIC can accept the reset response time to avoid this issue.
>
> In other words, the system will be always reboot if we make the
> OTP pin is connected the others IC to control the power.
>
> Signed-off-by: Caesar Wang <wxt at rock-chips.com>
> Reviewed-by: Douglas Anderson <dianders at chromium.org>
Acked-by: Rob Herring <robh at kernel.org>
> ---
>
> Changes in v4: None
> Changes in v3:
> - Add the pictrl states decription in document.
>
> Changes in v2:
> - Add the 'init' pinctrl more decription in commit.
> - Fix the subject to make more obvious in PATCH[1/2]
> - Resend this patch v2 since fix the subject to be specific.
>
> Changes in v1:
> - As the Doug comments, add the 'init' property to sync document.
>
> .../devicetree/bindings/thermal/rockchip-thermal.txt | 11 +++++++++--
> 1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
> index ef802de..b38200d 100644
> --- a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
> +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt
> @@ -12,6 +12,11 @@ Required properties:
> - resets : Must contain an entry for each entry in reset-names.
> See ../reset/reset.txt for details.
> - reset-names : Must include the name "tsadc-apb".
> +- pinctrl-names : The pin control state names;
> +- pinctrl-0 : The "init" pinctrl state, it will be set before device probe.
> +- pinctrl-1 : The "default" pinctrl state, it will be set after reset the
> + TSADC controller.
> +- pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend.
> - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
> - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value.
> - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO.
> @@ -27,8 +32,10 @@ tsadc: tsadc at ff280000 {
> clock-names = "tsadc", "apb_pclk";
> resets = <&cru SRST_TSADC>;
> reset-names = "tsadc-apb";
> - pinctrl-names = "default";
> - pinctrl-0 = <&otp_out>;
> + pinctrl-names = "init", "default", "sleep";
> + pinctrl-0 = <&otp_gpio>;
> + pinctrl-1 = <&otp_out>;
> + pinctrl-2 = <&otp_gpio>;
> #thermal-sensor-cells = <1>;
> rockchip,hw-tshut-temp = <95000>;
> rockchip,hw-tshut-mode = <0>;
> --
> 1.9.1
>
More information about the linux-arm-kernel
mailing list