[PATCH] usb: musb: dsps: handle the otg_state_a_wait_vrise_timeout case

[Gregory CLEMENT]

Hi Felipe,
 
 On lun., oct. 05 2015, Felipe Balbi <balbi at ti.com> wrote:


>> So after many tests on different devices, 200ms is enough for most of
>> them, but for one, 2000ms (2s) was needed!
>>
>> I see several option:
>> - adding a sysfs entry to setup the time
>> - adding a debugs entry entry
>> - adding configuration option in menuconfig
>> - using 2000ms and hopping it was enough for everyone
>>
>> My preference would go to the first option, what is your opinion?
>
> I'm not sure if either of them is good. man 2s is just too large. If the
> device isn't following the specification, I'm afraid that device needs
> to be fixed.
>
> I think the real issue here is the lack of a disconnect IRQ from AM335x
> devices. But here's something I've been meaning to test but never had
> time. If you look into AM335x address space, there's a bit in the
> wrapper which tells it to use the standard MUSB registers for IRQ,
> instead of the TI-specific thing. Can you see if we get a disconnect IRQ
> with that ?
>
> TRM is at [1], see page 2566. Basically, if you set bit 3 in register
> offset 0x1014, then it should use Mentor IRQ registers. If that works,
> quite a few problems will actually vanish :-p

So I tried it with the following patch:

-------------------------------------
diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
index c791ba5..c714500 100644
--- a/drivers/usb/musb/musb_dsps.c
+++ b/drivers/usb/musb/musb_dsps.c
@@ -470,6 +470,7 @@ static int dsps_musb_init(struct musb *musb)
 
        /* Reset the musb */
        dsps_writel(reg_base, wrp->control, (1 << wrp->reset));
+       dsps_writel(musb->ctrl_base, wrp->control, BIT(3));
 
        musb->isr = dsps_interrupt;
 
@@ -625,6 +626,7 @@ static int dsps_musb_reset(struct musb *musb)
        if (session_restart || !glue->sw_babble_enabled) {
                dev_info(musb->controller, "Restarting MUSB to recover from Babble\n");
                dsps_writel(musb->ctrl_base, wrp->control, (1 << wrp->reset));
+               dsps_writel(musb->ctrl_base, wrp->control, BIT(3));
                usleep_range(100, 200);
                usb_phy_shutdown(musb->xceiv);
                usleep_range(100, 200);
------------------------------------

I am not very familiar with that driver but my understanding was that
the Mentor IRQ registeres are managed by the musb_interrupt() function
which is called from the dsps_interrupt() interrupt handler.

Am I right?

if it is the case then it didn't fix the issue I had.

I activated the following debug line:

[musb_hdrc]musb_interrupt =_ "** IRQ %s usb%04x tx%04x rx%04x\012"
[musb_dsps]dsps_interrupt =p "usbintr (%x) epintr(%x)\012"

But I didn't get any interrupt while disconnecting the cable without any
device connected on it (whereas I got an interrupt when I connected it).

Note that I applied this patch instead of the "usb: musb: dsps: handle
the otg_state_a_wait_vrise_timeout case", is what you had in mind ?

Gregory

>
> [1] http://www.ti.com/lit/ug/spruh73l/spruh73l.pdf
>
> -- 
> balbi

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com