[PATCH v3 08/10] clk: ns2: add clock support for Broadcom Northstar 2 SoC

[Scott Branden]

Hi Ray,

Comment at near end.

On 15-10-15 01:55 PM, Ray Jui wrote:
>
>
> On 10/15/2015 1:40 PM, Scott Branden wrote:
>> We need some sort of kconfig option to differentiate NS2 clock driver
>> from being pulled in all the time.
>>
>> On 15-10-15 12:48 PM, Jon Mason wrote:
>>> The Broadcom Northstar 2 SoC is architected under the iProc
>>> architecture. It has the following PLLs: GENPLL SCR, GENPLL SW,
>>> LCPLL DDR, LCPLL Ports, all derived from an onboard crystal.
>>>
>>> Signed-off-by: Jon Mason <jonmason at broadcom.com>
>>> ---
>>>    drivers/clk/Makefile                |   2 +-
>>>    drivers/clk/bcm/Makefile            |   1 +
>>>    drivers/clk/bcm/clk-ns2.c           | 288
>>> ++++++++++++++++++++++++++++++++++++
>>>    include/dt-bindings/clock/bcm-ns2.h |  72 +++++++++
>>>    4 files changed, 362 insertions(+), 1 deletion(-)
>>>    create mode 100644 drivers/clk/bcm/clk-ns2.c
>>>    create mode 100644 include/dt-bindings/clock/bcm-ns2.h
>>>
>>> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
>>> index d08b3e5..6124bd3 100644
>>> --- a/drivers/clk/Makefile
>>> +++ b/drivers/clk/Makefile
>>> @@ -47,7 +47,7 @@ obj-$(CONFIG_COMMON_CLK_WM831X)        += clk-wm831x.o
>>>    obj-$(CONFIG_COMMON_CLK_XGENE)        += clk-xgene.o
>>>    obj-$(CONFIG_COMMON_CLK_PWM)        += clk-pwm.o
>>>    obj-$(CONFIG_COMMON_CLK_AT91)        += at91/
>>> -obj-$(CONFIG_ARCH_BCM)            += bcm/
>>> +obj-y                    += bcm/
>>>    obj-$(CONFIG_ARCH_BERLIN)        += berlin/
>>>    obj-$(CONFIG_ARCH_HISI)            += hisilicon/
>>>    obj-$(CONFIG_ARCH_MXC)            += imx/
>>> diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
>>> index e258b28..2d1cbc5 100644
>>> --- a/drivers/clk/bcm/Makefile
>>> +++ b/drivers/clk/bcm/Makefile
>>> @@ -3,6 +3,7 @@ obj-$(CONFIG_CLK_BCM_KONA)    += clk-kona-setup.o
>>>    obj-$(CONFIG_CLK_BCM_KONA)    += clk-bcm281xx.o
>>>    obj-$(CONFIG_CLK_BCM_KONA)    += clk-bcm21664.o
>>>    obj-$(CONFIG_COMMON_CLK_IPROC)    += clk-iproc-armpll.o
>>> clk-iproc-pll.o clk-iproc-asiu.o
>>> +obj-$(CONFIG_COMMON_CLK_IPROC)    += clk-ns2.o
>>
>> NS2 code is dragged in for all IPROC SoCs.  We need a config option for
>> NS2 (CONFIG_ARCH_BCM_NS2) to avoid this (if Arnd allows this for ARMv8
>> processors... ?).
>>
>> You can see below ARMv7 processors don't have this problem.
>>
>
> The arm64 maintainers (Catalin, Mark, and etc.) stated they only want
> one ARCH options per chip family.
>
>> If not we need to add CONFIG_CLK_NS2.
>
> If using CONFIG_CLK_NS2, how is it going to be enabled/selected?

Since CONFIG_ARCH_BCM_NS2 isn't "allowed" to be introduced we will need 
to create and select a CONFIG_CLK_BCM_NS2 in the defconfig instead.
>
> Ray
>

Regards,
  Scott