[PATCH 01/13] ARM: add some L220 DT settings

[Linus Walleij]

The RealView ARM11MPCore enables parity, eventmon and shared
override in the cache controller through its current boardfile,
but the code and DT bindings for the ARM L220 is currently
lacking the ability to set this up from DT. Add the required
bool parameters.

Cc: devicetree at vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
I know this patch mixes code and DT changes but it is silly to
split such a small patch. Will submit this to Russell's patch
tracker if it looks OK to the DT people. (Or if they are quiet.)
---
 Documentation/devicetree/bindings/arm/l2cc.txt | 10 ++++++----
 arch/arm/mm/cache-l2x0.c                       | 15 +++++++++++++++
 2 files changed, 21 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index 06c88a4d28ac..4d262e9b3464 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -67,12 +67,14 @@ Optional properties:
   disable if zero.
 - arm,prefetch-offset : Override prefetch offset value. Valid values are
   0-7, 15, 23, and 31.
-- arm,shared-override : The default behavior of the pl310 cache controller with
-  respect to the shareable attribute is to transform "normal memory
-  non-cacheable transactions" into "cacheable no allocate" (for reads) or
-  "write through no write allocate" (for writes).
+- arm,shared-override : The default behavior of the PL220 or PL310 cache
+  controllers with respect to the shareable attribute is to transform "normal
+  memory non-cacheable transactions" into "cacheable no allocate" (for reads)
+  or "write through no write allocate" (for writes).
   On systems where this may cause DMA buffer corruption, this property must be
   specified to indicate that such transforms are precluded.
+- arm,parity-enable : enable parity checking on the L2 cache (PL220 only).
+- arm,eventmon-enable : enable the event monitor on the L2 cache (PL220 only).
 - prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1>
   (forcibly enable), property absent (retain settings set by firmware)
 - prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable),
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 493692d838c6..d4e9fa2594f3 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -1060,6 +1060,21 @@ static void __init l2x0_of_parse(const struct device_node *np,
 		val |= (dirty - 1) << L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT;
 	}
 
+	if (of_property_read_bool(np, "arm,parity-enable")) {
+		mask &= ~L2C_AUX_CTRL_PARITY_ENABLE;
+		val |= L2C_AUX_CTRL_PARITY_ENABLE;
+	}
+
+	if (of_property_read_bool(np, "arm,eventmon-enable")) {
+		mask &= ~L2C_AUX_CTRL_EVTMON_ENABLE;
+		val |= L2C_AUX_CTRL_EVTMON_ENABLE;
+	}
+
+	if (of_property_read_bool(np, "arm,shared-override")) {
+		mask &= ~L2C_AUX_CTRL_SHARED_OVERRIDE;
+		val |= L2C_AUX_CTRL_SHARED_OVERRIDE;
+	}
+
 	ret = l2x0_cache_size_of_parse(np, aux_val, aux_mask, &assoc, SZ_256K);
 	if (ret)
 		return;
-- 
2.4.3