[PATCH 2/3] ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
Tony Lindgren
tony at atomide.com
Tue Oct 13 10:18:47 PDT 2015
Looks like thevarious omap5-uevm models and igepv5 are very similar. So let's
create omap5-board-common.dtsi to allow fixing up things properly for mainline
kernel to support all these.
Even if we eventually end up having only PMIC + MMC + eMMC + SDIO WLAN + SATA +
USB + HDMI configuration in the omap5-board-common.dtsi, this is the easiest
way to add support for other boards rather than diffing various versions of
out of tree dts files.
My guess is that also omap5-sbc-t54.dts can use this, but I don't have that
board so that will need to be dealt with later on.
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
.../{omap5-uevm.dts => omap5-board-common.dtsi} | 38 +-
arch/arm/boot/dts/omap5-uevm.dts | 662 +--------------------
2 files changed, 17 insertions(+), 683 deletions(-)
copy arch/arm/boot/dts/{omap5-uevm.dts => omap5-board-common.dtsi} (95%)
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-board-common.dtsi
similarity index 95%
copy from arch/arm/boot/dts/omap5-uevm.dts
copy to arch/arm/boot/dts/omap5-board-common.dtsi
index f10b42f..5cf76a1 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -5,21 +5,11 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/dts-v1/;
-
#include "omap5.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
- model = "TI OMAP5 uEVM board";
- compatible = "ti,omap5-uevm", "ti,omap5";
-
- memory {
- device_type = "memory";
- reg = <0x80000000 0x7F000000>; /* 2032 MB */
- };
-
aliases {
display0 = &hdmi0;
};
@@ -80,9 +70,7 @@
pinctrl-names = "default";
pinctrl-0 = <&tpd12s015_pins>;
- gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */
- <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */
- <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
+ /* gpios defined in the board specific dts */
ports {
#address-cells = <1>;
@@ -190,13 +178,6 @@
>;
};
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
- 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
- >;
- };
-
mcspi2_pins: pinmux_mcspi2_pins {
pinctrl-single,pins = <
0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
@@ -587,20 +568,6 @@
};
};
-&i2c5 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins>;
-
- clock-frequency = <400000>;
-
- gpio9: gpio at 22 {
- compatible = "ti,tca6424";
- reg = <0x22>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-};
-
&mcpdm {
pinctrl-names = "default";
pinctrl-0 = <&mcpdm_pins>;
@@ -674,7 +641,8 @@
&hdmi {
status = "ok";
- vdda-supply = <&ldo4_reg>;
+
+ /* vdda-supply populated in board specific dts file */
pinctrl-names = "default";
pinctrl-0 = <&dss_hdmi_pins>;
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index f10b42f..05b1c1e 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -7,9 +7,7 @@
*/
/dts-v1/;
-#include "omap5.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "omap5-board-common.dtsi"
/ {
model = "TI OMAP5 uEVM board";
@@ -19,572 +17,10 @@
device_type = "memory";
reg = <0x80000000 0x7F000000>; /* 2032 MB */
};
-
- aliases {
- display0 = &hdmi0;
- };
-
- vmmcsd_fixed: fixedregulator-mmcsd {
- compatible = "regulator-fixed";
- regulator-name = "vmmcsd_fixed";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- mmc3_pwrseq: sdhci0_pwrseq {
- compatible = "mmc-pwrseq-simple";
- clocks = <&clk32kgaudio>;
- clock-names = "ext_clock";
- };
-
- vmmcsdio_fixed: fixedregulator-mmcsdio {
- compatible = "regulator-fixed";
- regulator-name = "vmmcsdio_fixed";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
- enable-active-high;
- startup-delay-us = <70000>;
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_pins>;
- };
-
- /* HS USB Host PHY on PORT 2 */
- hsusb2_phy: hsusb2_phy {
- compatible = "usb-nop-xceiv";
- reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
- clocks = <&auxclk1_ck>;
- clock-names = "main_clk";
- clock-frequency = <19200000>;
- };
-
- /* HS USB Host PHY on PORT 3 */
- hsusb3_phy: hsusb3_phy {
- compatible = "usb-nop-xceiv";
- reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
- };
-
- leds {
- compatible = "gpio-leds";
- led at 1 {
- label = "omap5:blue:usr1";
- gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
- };
-
- tpd12s015: encoder at 0 {
- compatible = "ti,tpd12s015";
-
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
- gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */
- <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */
- <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
-
- tpd12s015_in: endpoint at 0 {
- remote-endpoint = <&hdmi_out>;
- };
- };
-
- port at 1 {
- reg = <1>;
-
- tpd12s015_out: endpoint at 0 {
- remote-endpoint = <&hdmi_connector_in>;
- };
- };
- };
- };
-
- hdmi0: connector at 0 {
- compatible = "hdmi-connector";
- label = "hdmi";
-
- type = "b";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&tpd12s015_out>;
- };
- };
- };
-
- sound: sound {
- compatible = "ti,abe-twl6040";
- ti,model = "omap5-uevm";
-
- ti,mclk-freq = <19200000>;
-
- ti,mcpdm = <&mcpdm>;
-
- ti,twl6040 = <&twl6040>;
-
- /* Audio routing */
- ti,audio-routing =
- "Headset Stereophone", "HSOL",
- "Headset Stereophone", "HSOR",
- "Line Out", "AUXL",
- "Line Out", "AUXR",
- "HSMIC", "Headset Mic",
- "Headset Mic", "Headset Mic Bias",
- "AFML", "Line In",
- "AFMR", "Line In";
- };
-};
-
-&omap5_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <
- &usbhost_pins
- &led_gpio_pins
- >;
-
- twl6040_pins: pinmux_twl6040_pins {
- pinctrl-single,pins = <
- 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
- >;
- };
-
- mcpdm_pins: pinmux_mcpdm_pins {
- pinctrl-single,pins = <
- 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
- 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
- 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
- 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
- 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
- >;
- };
-
- mcbsp1_pins: pinmux_mcbsp1_pins {
- pinctrl-single,pins = <
- 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
- 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
- 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
- 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
- >;
- };
-
- mcbsp2_pins: pinmux_mcbsp2_pins {
- pinctrl-single,pins = <
- 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
- 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
- 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
- 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
- >;
- };
-
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
- 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
- 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
- >;
- };
-
- mcspi2_pins: pinmux_mcspi2_pins {
- pinctrl-single,pins = <
- 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
- 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
- 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
- 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
- >;
- };
-
- mcspi3_pins: pinmux_mcspi3_pins {
- pinctrl-single,pins = <
- 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
- 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
- 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
- 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
- >;
- };
-
- mmc3_pins: pinmux_mmc3_pins {
- pinctrl-single,pins = <
- OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
- OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
- OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
- OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
- OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
- OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
- >;
- };
-
- wlan_pins: pinmux_wlan_pins {
- pinctrl-single,pins = <
- OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
- >;
- };
-
- usbhost_pins: pinmux_usbhost_pins {
- pinctrl-single,pins = <
- 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
- 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
-
- 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
- 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
-
- 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
- 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
- >;
- };
-
- led_gpio_pins: pinmux_led_gpio_pins {
- pinctrl-single,pins = <
- 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
- >;
- };
-
- uart1_pins: pinmux_uart1_pins {
- pinctrl-single,pins = <
- 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
- 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
- 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
- 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
- >;
- };
-
- uart3_pins: pinmux_uart3_pins {
- pinctrl-single,pins = <
- 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
- 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
- >;
- };
-
- uart5_pins: pinmux_uart5_pins {
- pinctrl-single,pins = <
- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
- 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
- 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
- 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
- >;
- };
-
- dss_hdmi_pins: pinmux_dss_hdmi_pins {
- pinctrl-single,pins = <
- 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
- 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
- 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
- >;
- };
};
-&omap5_pmx_wkup {
- pinctrl-names = "default";
- pinctrl-0 = <
- &usbhost_wkup_pins
- >;
-
- usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
- pinctrl-single,pins = <
- 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
- >;
- };
-
- wlcore_irq_pin: pinmux_wlcore_irq_pin {
- pinctrl-single,pins = <
- OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
- >;
- };
-};
-
-&mmc1 {
- vmmc-supply = <&ldo9_reg>;
- bus-width = <4>;
-};
-
-&mmc2 {
- vmmc-supply = <&vmmcsd_fixed>;
- bus-width = <8>;
- ti,non-removable;
-};
-
-&mmc3 {
- vmmc-supply = <&vmmcsdio_fixed>;
- mmc-pwrseq = <&mmc3_pwrseq>;
- bus-width = <4>;
- non-removable;
- cap-power-off-card;
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
- interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
- &omap5_pmx_core 0x168>;
-
- #address-cells = <1>;
- #size-cells = <0>;
- wlcore: wlcore at 2 {
- compatible = "ti,wl1271";
- reg = <2>;
- interrupt-parent = <&gpio1>;
- interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
- ref-clock-frequency = <26000000>;
- };
-};
-
-&mmc4 {
- status = "disabled";
-};
-
-&mmc5 {
- status = "disabled";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
-
- clock-frequency = <400000>;
-
- palmas: palmas at 48 {
- compatible = "ti,palmas";
- interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
- reg = <0x48>;
- interrupt-controller;
- #interrupt-cells = <2>;
- ti,system-power-controller;
-
- extcon_usb3: palmas_usb {
- compatible = "ti,palmas-usb-vid";
- ti,enable-vbus-detection;
- ti,enable-id-detection;
- ti,wakeup;
- };
-
- clk32kgaudio: palmas_clk32k at 1 {
- compatible = "ti,palmas-clk32kgaudio";
- #clock-cells = <0>;
- };
-
- palmas_pmic {
- compatible = "ti,palmas-pmic";
- interrupt-parent = <&palmas>;
- interrupts = <14 IRQ_TYPE_NONE>;
- interrupt-name = "short-irq";
-
- ti,ldo6-vibrator;
-
- regulators {
- smps123_reg: smps123 {
- /* VDD_OPP_MPU */
- regulator-name = "smps123";
- regulator-min-microvolt = < 600000>;
- regulator-max-microvolt = <1500000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps45_reg: smps45 {
- /* VDD_OPP_MM */
- regulator-name = "smps45";
- regulator-min-microvolt = < 600000>;
- regulator-max-microvolt = <1310000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps6_reg: smps6 {
- /* VDD_DDR3 - over VDD_SMPS6 */
- regulator-name = "smps6";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps7_reg: smps7 {
- /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
- regulator-name = "smps7";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps8_reg: smps8 {
- /* VDD_OPP_CORE */
- regulator-name = "smps8";
- regulator-min-microvolt = < 600000>;
- regulator-max-microvolt = <1310000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps9_reg: smps9 {
- /* VDDA_2v1_AUD over VDD_2v1 */
- regulator-name = "smps9";
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- ti,smps-range = <0x80>;
- };
-
- smps10_out2_reg: smps10_out2 {
- /* VBUS_5V_OTG */
- regulator-name = "smps10_out2";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps10_out1_reg: smps10_out1 {
- /* VBUS_5V_OTG */
- regulator-name = "smps10_out1";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- ldo1_reg: ldo1 {
- /* VDDAPHY_CAM: vdda_csiport */
- regulator-name = "ldo1";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo2_reg: ldo2 {
- /* VCC_2V8_DISP: Does not go anywhere */
- regulator-name = "ldo2";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- /* Unused */
- status = "disabled";
- };
-
- ldo3_reg: ldo3 {
- /* VDDAPHY_MDM: vdda_lli */
- regulator-name = "ldo3";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-boot-on;
- /* Only if Modem is used */
- status = "disabled";
- };
-
- ldo4_reg: ldo4 {
- /* VDDAPHY_DISP: vdda_dsiport/hdmi */
- regulator-name = "ldo4";
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1800000>;
- };
-
- ldo5_reg: ldo5 {
- /* VDDA_1V8_PHY: usb/sata/hdmi.. */
- regulator-name = "ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo6_reg: ldo6 {
- /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
- regulator-name = "ldo6";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo7_reg: ldo7 {
- /* VDD_VPP: vpp1 */
- regulator-name = "ldo7";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- /* Only for efuse reprograming! */
- status = "disabled";
- };
-
- ldo8_reg: ldo8 {
- /* VDD_3v0: Does not go anywhere */
- regulator-name = "ldo8";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-boot-on;
- /* Unused */
- status = "disabled";
- };
-
- ldo9_reg: ldo9 {
- /* VCC_DV_SDIO: vdds_sdcard */
- regulator-name = "ldo9";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3000000>;
- regulator-boot-on;
- };
-
- ldoln_reg: ldoln {
- /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
- regulator-name = "ldoln";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldousb_reg: ldousb {
- /* VDDA_3V_USB: VDDA_USBHS33 */
- regulator-name = "ldousb";
- regulator-min-microvolt = <3250000>;
- regulator-max-microvolt = <3250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- regen3_reg: regen3 {
- /* REGEN3 controls LDO9 supply to card */
- regulator-name = "regen3";
- regulator-always-on;
- regulator-boot-on;
- };
- };
- };
-
- palmas_power_button: palmas_power_button {
- compatible = "ti,palmas-pwrbutton";
- interrupt-parent = <&palmas>;
- interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
- wakeup-source;
- };
- };
-
- twl6040: twl at 4b {
- compatible = "ti,twl6040";
- reg = <0x4b>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&twl6040_pins>;
-
- interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
- ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */
-
- vio-supply = <&smps7_reg>;
- v2v1-supply = <&smps9_reg>;
- enable-active-high;
-
- clocks = <&clk32kgaudio>;
- clock-names = "clk32k";
- };
+&hdmi {
+ vdda-supply = <&ldo4_reg>;
};
&i2c5 {
@@ -601,87 +37,17 @@
};
};
-&mcpdm {
- pinctrl-names = "default";
- pinctrl-0 = <&mcpdm_pins>;
- status = "okay";
-};
-
-&mcbsp1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcbsp1_pins>;
- status = "okay";
-};
-
-&mcbsp2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcbsp2_pins>;
- status = "okay";
-};
-
-&usbhshost {
- port2-mode = "ehci-hsic";
- port3-mode = "ehci-hsic";
-};
-
-&usbhsehci {
- phys = <0 &hsusb2_phy &hsusb3_phy>;
-};
-
-&usb3 {
- extcon = <&extcon_usb3>;
- vbus-supply = <&smps10_out1_reg>;
-};
-
-&mcspi1 {
-
-};
-
-&mcspi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcspi2_pins>;
-};
-
-&mcspi3 {
- pinctrl-names = "default";
- pinctrl-0 = <&mcspi3_pins>;
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins>;
- interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
- <&omap5_pmx_core 0x19c>;
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart5_pins>;
-};
-
-&cpu0 {
- cpu0-supply = <&smps123_reg>;
-};
-
-&dss {
- status = "ok";
+&omap5_pmx_core {
+ i2c5_pins: pinmux_i2c5_pins {
+ pinctrl-single,pins = <
+ 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
+ 0x188 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
+ >;
+ };
};
-&hdmi {
- status = "ok";
- vdda-supply = <&ldo4_reg>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&dss_hdmi_pins>;
-
- port {
- hdmi_out: endpoint {
- remote-endpoint = <&tpd12s015_in>;
- };
- };
+&tpd12s015 {
+ gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>, /* TCA6424A P01, CT CP HPD */
+ <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */
+ <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
};
--
2.1.4
More information about the linux-arm-kernel
mailing list