[PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support

Jaehoon Chung jh80.chung at samsung.com
Mon Oct 12 06:04:31 PDT 2015


On 10/12/2015 09:42 PM, Krzysztof Kozlowski wrote:
> W dniu 12.10.2015 o 19:46, Anand Moon pisze:
>> Hi Krzysztof,
>>
>> On 12 October 2015 at 11:14, Krzysztof Kozlowski
>> <k.kozlowski at samsung.com> wrote:
>>> On 12.10.2015 00:46, Anand Moon wrote:
>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104)
>>>
>>> This description is not entirely correct. The MMC driver already
>>> supports these UHS speeds (you did not any code) so you rather enabled
>>> it (description of bindings says "is supported").
>>>
>>> You mentioned DDR50 but I don't see respective property below.
>> Looks like I missed it, I will add this in the next patch,
>>>
>>> How do you know that these modes are really supported? I don't know. Can
>>> you convince me?
> 
> That part was not answered...

In my experiment, it needs two requirements.
One is that Host controller supported UHS-I mode or others, other is SD-card.
In Anand's commit message, there is no information for this.

And 50MB/s or 104MB/s is not real performance. (Just theoretical values)
It seems that can get those performances.

> 
>>>
>>
>>>>
>>>> Signed-off-by: Anand Moon <linux.amoon at gmail.com>
>>>>
>>>> ---
>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch
>>>>
>>>> Changes Fixed the UHS-I bus speed detedtion on cold boot.
>>>
>>> I don't get what is exactly fixed here. What was the error? What is the
>>> outcome of this fix? The log below is before or after?
>>>
>>> Best regards,
>>> Krzysztof
>>>
>>>>
>>>> [    2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
>>>> [    2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>>>> [    2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>>>> [    2.461743]  mmcblk0: p1 p2
>>>
>>>> ---
>>>>  arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++
>>>>  1 file changed, 4 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>>> index 58c06d3..ba4a87b 100644
>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>>> @@ -364,6 +364,10 @@
>>>>       pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>>>>       bus-width = <4>;
>>>>       cap-sd-highspeed;
>>>> +     sd-uhs-sdr12;
>>>> +     sd-uhs-sdr25;
>>>> +     sd-uhs-sdr50;
>>>> +     sd-uhs-sdr104;
>>>>  };
>>>>
>>>>  &pinctrl_0 {
>>>>
>>>
>>
>> Changes were made to support Sandisk Ultra UHS-I class 10 card support.
>> OdroidXU3/XU4 board would not boot up using this card.
>>
>> Depending on the capability of the UHS-I card, the speed of the card
>> is selected.
>> I have just added the enhance capability feature to support them.
> 
> So without these capabilities mentioned microSD card cannot be used? So
> I have a UHS-I card, that one exactly:
> http://www.samsung.com/us/support/owners/product/MB-MP32D/APC
> 
> It works:
> [    2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req
> 50000000Hz, actual 50000000HZ div = 0)
> [    2.693296] mmc1: new high speed SDHC card at address 0001
> [    2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB
> [    2.708406]  mmcblk0: p1 p2
> 
> This is just HS mode.
> 
> In the same time isn't UHS-I backward compatible? Your report seems
> surprising.

Right. it's not issue. just working as lower mode than its capability.

Best Regards,
Jaehoon Chung

> 
> Best regards,
> Krzysztof
> 
>>
>> On warm boot: i.e reboot of the board.
>> [    4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot
>> req 50000000Hz, actual 50000000HZ div = 0)
>> [    4.657555] mmc1: new high speed SDHC card at address aaaa
>> [    4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>> [    4.669206]  mmcblk0: p1 p2
>>
>> On cold boot:: ie: power on the board.
>>
>> [    4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot
>> req 100000000Hz, actual 100000000HZ div = 0)
>> [    4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa
>> [    4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB
>> [    4.650293] IRQ56 no longer affine to CPU7
>> [    4.650581] CPU7: shutdown
>> [    4.658293]  mmcblk0: p1 p2
>>
>> Note: Their is need to reset the PMIC
>> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers
>>          to support this feature consistently on every reboot.
>>
>> -Anand Moon
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>> the body of a message to majordomo at vger.kernel.org
>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>> Please read the FAQ at  http://www.tux.org/lkml/
>>
> 
> 




More information about the linux-arm-kernel mailing list