[PATCH 3/3] fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000

[Michal Simek]

Hi Mike,

On 10/12/2015 02:22 PM, Mike Looijmans wrote:
> On 12-10-15 13:16, Michal Simek wrote:
>>
>>>>> +static int zynq_fpga_ops_write(struct fpga_manager *mgr,
>>>>> +                            const char *buf, size_t count)
>>>>> +{
>>>>> +     struct zynq_fpga_priv *priv;
>>>>> +     int err;
>>>>> +     char *kbuf;
>>>>> +     size_t i, in_count;
>>>>> +     dma_addr_t dma_addr;
>>>>> +     u32 transfer_length = 0;
>>>>> +     bool endian_swap = false;
>>>>> +
>>>>> +     in_count = count;
>>>>> +     priv = mgr->priv;
>>>>> +
>>>>> +     kbuf = dma_alloc_coherent(priv->dev, count, &dma_addr,
>>>>> GFP_KERNEL);
>>>>> +     if (!kbuf)
>>>>> +             return -ENOMEM;
>>>>> +
>>>>> +     memcpy(kbuf, buf, count);
>>>>> +
>>>>> +     /* look for the sync word */
>>>>> +     for (i = 0; i < count - 4; i++) {
>>>>> +             if (memcmp(kbuf + i, "\x66\x55\x99\xAA", 4) == 0) {
>>>>> +                     dev_dbg(priv->dev, "Found normal sync word\n");
>>>>> +                     endian_swap = false;
>>>>> +                     break;
>>>>> +             }
>>
>> This is bin format
>>
>>>>> +             if (memcmp(kbuf + i, "\xAA\x99\x55\x66", 4) == 0) {
>>>>> +                     dev_dbg(priv->dev, "Found swapped sync word\n");
>>>>> +                     endian_swap = true;
>>>>> +                     break;
>>>>> +             }
>>
>> This is bit format from header
>>
>>>>> +     }
>>>>
>>>> How much control do we have over mandating the format of firmware at
>>>> this point?  It'd be swell if we could just mandate a specific
>>>> endianness, and leave this munging to usermode.
>>>
>>> That's a good question. Personally I do only care about one of both,
>>> but that's just because I get to decide for my targets...
>>> Opinions from the Xilinx guys?
>>
>> Don't know full history about this but in past bitstream in BIT format
>> was used. Which is header (partially decoding in u-boot for example)
>> with data.
>> On zynq native format is BIN which is format without header and data is
>> swapped.
>> This code just detects which format is used. If BIT, header is skipped
>> and data is swapped to BIN format.
>>
>> Back to origin question if this is something what can be handled from
>> user space. And answer is - yes it can be handled there.
>> But based on my experience it is very useful to be able to handle BIT
>> because it is built by tools by default.
>> Also with BIN format you are loosing record what this data bitstream
>> targets. Header in BIT gives you at least some ideas.
> 
> People should stop using "cat" to program the FPGA and use a userspace
> tool instead. I've already released such tools under GPL, so anyone can
> pick up on it and extend it as required.

Link?

This is fpga manager based driver where "cat" won't be used.

> 
> The header for the "bit" format is completely ignored (you can't even
> use it to determine if the bitstream is compatible with the current
> device) so there's no point in carrying it around. 

up2you what you want to do with it. If you work with different boards
with different FPGAs it is at least helpful to know if X.bit target this
or that board. Unfortunately I am not aware about any public document
which describe what there is written.

> On the zynq, doing
> the "swap" in userspace was measurably faster than having the driver
> handle it, and that was even without using NEON instructions for byte
> swapping.
> 
> I admit that being able to do "cat static.bit > /dev/xdevcfg" has had
> its uses. But it's not something that belongs in mainline Linux.

It is about comfort but I have really not a problem that driver will
handle just BIN format.

> Probably one of the key reasons that the "bit" format is still popular
> is that getting the Vivado tools to create a proper "bin" that will
> actually work on the Zynq is about as easy as nailing jelly to a tree.
> We've been using a simple Python script to do the bit->bin conversion
> for that reason.

In vivado it is one tcl cmd. But truth is that I don't really get why
BIN is not generated by default.

> Using the "bin" format in the driver keeps it simple and singular.
> Userspace tools can add whatever wrappers and headers they feel
> appropriate to it, these checks don't belong in the driver since they
> will be application specific. For example, some users would want to
> verify that a partial bitstream actually matches the static part that's
> currently in the FPGA.

agree.

Thanks,
Michal