[PATCH 1/2] irqchip: sunxi-nmi: Use driver name instead of DT node name for identification

[Chen-Yu Tsai]

On Fri, Oct 2, 2015 at 4:14 AM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi,
>
> On Thu, Oct 01, 2015 at 11:33:48PM +0800, Chen-Yu Tsai wrote:
>> The device tree node name is typically "interrupt-controller", which is
>> rather useless when used in printk messages and irq chip names for
>> identification purposes. Use the driver name "sunxi-nmi" instead.
>>
>> Signed-off-by: Chen-Yu Tsai <wens at csie.org>
>> ---
>>  drivers/irqchip/irq-sunxi-nmi.c | 11 ++++++-----
>>  1 file changed, 6 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/irqchip/irq-sunxi-nmi.c b/drivers/irqchip/irq-sunxi-nmi.c
>> index c143dd58410c..57e009917d2d 100644
>> --- a/drivers/irqchip/irq-sunxi-nmi.c
>> +++ b/drivers/irqchip/irq-sunxi-nmi.c
>> @@ -21,6 +21,7 @@
>>  #include <linux/irqchip/chained_irq.h>
>>
>>  #define SUNXI_NMI_SRC_TYPE_MASK      0x00000003
>> +#define DRV_NAME "sunxi-nmi"
>>
>>  enum {
>>       SUNXI_SRC_TYPE_LEVEL_LOW = 0,
>> @@ -130,22 +131,22 @@ static int __init sunxi_sc_nmi_irq_init(struct device_node *node,
>>
>>       domain = irq_domain_add_linear(node, 1, &irq_generic_chip_ops, NULL);
>>       if (!domain) {
>> -             pr_err("%s: Could not register interrupt domain.\n", node->name);
>> +             pr_err("%s: Could not register interrupt domain.\n", DRV_NAME);
>>               return -ENOMEM;
>>       }
>>
>> -     ret = irq_alloc_domain_generic_chips(domain, 1, 2, node->name,
>> +     ret = irq_alloc_domain_generic_chips(domain, 1, 2, DRV_NAME,
>>                                            handle_fasteoi_irq, clr, 0,
>>                                            IRQ_GC_INIT_MASK_CACHE);
>>       if (ret) {
>>                pr_err("%s: Could not allocate generic interrupt chip.\n",
>> -                      node->name);
>> +                      DRV_NAME);
>>                goto fail_irqd_remove;
>>       }
>>
>>       irq = irq_of_parse_and_map(node, 0);
>>       if (irq <= 0) {
>> -             pr_err("%s: unable to parse irq\n", node->name);
>> +             pr_err("%s: unable to parse irq\n", DRV_NAME);
>>               ret = -EINVAL;
>>               goto fail_irqd_remove;
>>       }
>> @@ -153,7 +154,7 @@ static int __init sunxi_sc_nmi_irq_init(struct device_node *node,
>>       gc = irq_get_domain_generic_chip(domain, 0);
>>       gc->reg_base = of_iomap(node, 0);
>>       if (!gc->reg_base) {
>> -             pr_err("%s: unable to map resource\n", node->name);
>> +             pr_err("%s: unable to map resource\n", DRV_NAME);
>
> All the pr_err changes can even be replaced by defining pr_fmt.

Cool. Learned something today.

ChenYu