[PATCH] PCI: imx6: Fix reset-gpio to work with active low GPIO
Lucas Stach
l.stach at pengutronix.de
Tue Nov 24 05:55:34 PST 2015
Hi Petr,
sorry for the delay in reviewing this.
Am Montag, den 16.11.2015, 16:19 +0100 schrieb Petr Štetiar:
> It's currently not possible to use reset-gpio on board where the GPIO is
> active low as the code incorrectly assumes, that reset-gpio will be
> always active high.
>
I see the need for this change, but I'm not completely happy with the
implementation.
> In my case the broken behavior was observed on Toradex Apalis SoM with
> Ixora base board.
>
> Signed-off-by: Petr Štetiar <ynezz at true.cz>
> ---
> drivers/pci/host/pci-imx6.c | 15 +++++++++++----
> 1 file changed, 11 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
> index fdb9536..cd7ed71 100644
> --- a/drivers/pci/host/pci-imx6.c
> +++ b/drivers/pci/host/pci-imx6.c
> @@ -293,9 +293,11 @@ static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
>
> /* Some boards don't have PCIe reset GPIO. */
> if (gpio_is_valid(imx6_pcie->reset_gpio)) {
> - gpio_set_value(imx6_pcie->reset_gpio, 0);
> + struct gpio_desc *gd = gpio_to_desc(imx6_pcie->reset_gpio);
> +
> + gpiod_set_value(gd, 0);
> msleep(100);
> - gpio_set_value(imx6_pcie->reset_gpio, 1);
> + gpiod_set_value(gd, 1);
> }
> return 0;
>
> @@ -559,6 +561,8 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
> struct pcie_port *pp;
> struct device_node *np = pdev->dev.of_node;
> struct resource *dbi_base;
> + enum of_gpio_flags of_flags;
> + int flags = GPIOF_OUT_INIT_LOW;
> int ret;
>
> imx6_pcie = devm_kzalloc(&pdev->dev, sizeof(*imx6_pcie), GFP_KERNEL);
> @@ -578,10 +582,13 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
> return PTR_ERR(pp->dbi_base);
>
> /* Fetch GPIOs */
> - imx6_pcie->reset_gpio = of_get_named_gpio(np, "reset-gpio", 0);
> + imx6_pcie->reset_gpio = of_get_named_gpio_flags(np, "reset-gpio", 0,
> +
Rather than adding all this complexity to this function, this should
really be switched over to the descriptor based GPIO interface as a
whole. So the above should become a single call to
"devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW)" and the dependent
code changed accordingly.
Regards,
Lucas
> &of_flags);
> if (gpio_is_valid(imx6_pcie->reset_gpio)) {
> + if (of_flags & OF_GPIO_ACTIVE_LOW)
> + flags |= GPIOF_ACTIVE_LOW;
> ret = devm_gpio_request_one(&pdev->dev, imx6_pcie->reset_gpio,
> - GPIOF_OUT_INIT_LOW, "PCIe reset");
> + flags, "PCIe reset");
> if (ret) {
> dev_err(&pdev->dev, "unable to get reset gpio\n");
> return ret;
--
Pengutronix e.K. | Lucas Stach |
Industrial Linux Solutions | http://www.pengutronix.de/ |
More information about the linux-arm-kernel
mailing list