[RFC] asm-generic: default BUG_ON(x) to "if(x) BUG()"

[Willy Tarreau]

Hi Arnd,

On Mon, Nov 23, 2015 at 05:25:28PM +0100, Arnd Bergmann wrote:
> When CONFIG_BUG is disabled, BUG_ON() will only evaluate the condition,
> but will not actually stop the current thread. GCC warns about a couple
> of BUG_ON() users where this actually leads to further undefined
> behavior:
> 
> include/linux/ceph/osdmap.h: In function 'ceph_can_shift_osds':
> include/linux/ceph/osdmap.h:54:1: warning: control reaches end of non-void function
> fs/ext4/inode.c: In function 'ext4_map_blocks':
> fs/ext4/inode.c:548:5: warning: 'retval' may be used uninitialized in this function
> drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
> drivers/mfd/db8500-prcmu.c:762:10: warning: 'div_mask' may be used uninitialized in this function
> drivers/mfd/db8500-prcmu.c:769:13: warning: 'mask' may be used uninitialized in this function
> drivers/mfd/db8500-prcmu.c:757:7: warning: 'bits' may be used uninitialized in this function
> drivers/tty/serial/8250/8250_core.c: In function 'univ8250_release_irq':
> drivers/tty/serial/8250/8250_core.c:252:18: warning: 'i' may be used uninitialized in this function
> drivers/tty/serial/8250/8250_core.c:235:19: note: 'i' was declared here
> 
> There is an obvious conflict of interest here: on the one hand, someone
> who disables CONFIG_BUG() will want the kernel to be as small as possible
> and doesn't care about printing error messages to a console that nobody
> looks at. On the other hand, running into a BUG_ON() condition means that
> something has gone wrong, and we probably want to also stop doing things
> that might cause data corruption.
> 
> This patch picks the second choice, and changes the NOP to BUG(), which
> normally stops the execution of the current thread in some form (endless
> loop or a trap). This follows the logic we applied in a4b5d580e078 ("bug:
> Make BUG() always stop the machine").
> 
> For ARM multi_v7_defconfig, the size slightly increases:
> 
> section		CONFIG_BUG=y	CONFIG_BUG=n	CONFIG_BUG=n+patch
> 
>   .text            8320248   |     8180944   |     8207688
>   .rodata          3633720   |     3567144   |     3570648
>   __bug_table        32508   |         ---   |         ---
>   __modver             692   |        1584   |        2176
>   .init.text        558132   |      548300   |      550088
>   .exit.text         12380   |       12256   |       12380
>   .data            1016672   |     1016064   |     1016128
>   Total           14622556   |    14374510   |    14407326
> 
> So instead of saving 1.70% of the total image size, we only save 1.48%
> by turning off CONFIG_BUG, but in return we can ensure that we don't run
> into cases of uninitialized variable or return code uses when something
> bad happens. Aside from that, we significantly reduce the number of
> warnings in randconfig builds, which makes it easier to fix the warnings
> about other problems.

I think you could do better by simply calling panic("BUG!") instead as
BUG() does. It will avoid the printk() call and pushing the file/line
number onto the stack. It will also probably not inflate the rodata this
way.

Regards,
Willy