[PATCH v2] fpga: zynq-fpga: Enable pm_runtime (suspend, resume)
Mike Looijmans
mike.looijmans at topic.nl
Thu Nov 19 23:25:27 PST 2015
On 19-11-15 23:07, Moritz Fischer wrote:
> Replaced constant clock_{enable,disable} calls with pm_runtime
> hooks for suspend and resume to avoid constant clk_enable /
> clk_disable.
>
> Acked-by: Alan Tull <atull at opensource.altera.com>
> Signed-off-by: Moritz Fischer <moritz.fischer at ettus.com>
> ---
> Changes:
>
> v1:
> - Removed superfluous #ifdef CONFIG_PM as suggested by Michal
> - Changed commit message to include suspend / resume
> - Added Alan's Acked-by
>
> drivers/fpga/zynq-fpga.c | 76 +++++++++++++++++++++++++++++++++++++-----------
> 1 file changed, 59 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/fpga/zynq-fpga.c b/drivers/fpga/zynq-fpga.c
> index c2fb412..3f5469d 100644
> --- a/drivers/fpga/zynq-fpga.c
> +++ b/drivers/fpga/zynq-fpga.c
> @@ -28,6 +28,7 @@
> #include <linux/of_address.h>
> #include <linux/of_irq.h>
> #include <linux/pm.h>
> +#include <linux/pm_runtime.h>
> #include <linux/regmap.h>
> #include <linux/string.h>
>
> @@ -184,8 +185,8 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr, u32 flags,
>
> priv = mgr->priv;
>
> - err = clk_enable(priv->clk);
> - if (err)
> + err = pm_runtime_get_sync(priv->dev);
> + if (err < 0)
> return err;
>
> /* don't globally reset PL if we're doing partial reconfig */
> @@ -271,12 +272,12 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr, u32 flags,
> ctrl = zynq_fpga_read(priv, MCTRL_OFFSET);
> zynq_fpga_write(priv, MCTRL_OFFSET, (~MCTRL_PCAP_LPBK_MASK & ctrl));
>
> - clk_disable(priv->clk);
> + pm_runtime_put(priv->dev);
>
> return 0;
>
> out_err:
> - clk_disable(priv->clk);
> + pm_runtime_put(priv->dev);
>
> return err;
> }
> @@ -301,9 +302,8 @@ static int zynq_fpga_ops_write(struct fpga_manager *mgr,
>
> memcpy(kbuf, buf, count);
>
> - /* enable clock */
> - err = clk_enable(priv->clk);
> - if (err)
> + err = pm_runtime_get_sync(priv->dev);
> + if (err < 0)
> goto out_free;
>
> zynq_fpga_write(priv, INT_STS_OFFSET, IXR_ALL_MASK);
> @@ -335,7 +335,7 @@ static int zynq_fpga_ops_write(struct fpga_manager *mgr,
> err = -EFAULT;
> }
>
> - clk_disable(priv->clk);
> + pm_runtime_put(priv->dev);
>
> out_free:
> dma_free_coherent(priv->dev, in_count, kbuf, dma_addr);
> @@ -349,8 +349,8 @@ static int zynq_fpga_ops_write_complete(struct fpga_manager *mgr, u32 flags)
> int err;
> u32 intr_status;
>
> - err = clk_enable(priv->clk);
> - if (err)
> + err = pm_runtime_get_sync(priv->dev);
> + if (err < 0)
> return err;
>
> err = zynq_fpga_poll_timeout(priv, INT_STS_OFFSET, intr_status,
> @@ -358,7 +358,7 @@ static int zynq_fpga_ops_write_complete(struct fpga_manager *mgr, u32 flags)
> INIT_POLL_DELAY,
> INIT_POLL_TIMEOUT);
>
> - clk_disable(priv->clk);
> + pm_runtime_put(priv->dev);
>
> if (err)
> return err;
> @@ -385,12 +385,12 @@ static enum fpga_mgr_states zynq_fpga_ops_state(struct fpga_manager *mgr)
>
> priv = mgr->priv;
>
> - err = clk_enable(priv->clk);
> - if (err)
> + err = pm_runtime_get_sync(priv->dev);
> + if (err < 0)
> return FPGA_MGR_STATE_UNKNOWN;
>
> intr_status = zynq_fpga_read(priv, INT_STS_OFFSET);
> - clk_disable(priv->clk);
> + pm_runtime_put(priv->dev);
>
> if (intr_status & IXR_PCFG_DONE_MASK)
> return FPGA_MGR_STATE_OPERATING;
> @@ -457,19 +457,26 @@ static int zynq_fpga_probe(struct platform_device *pdev)
> return err;
> }
>
> + pm_runtime_get_noresume(&pdev->dev);
> + pm_runtime_set_active(&pdev->dev);
> + pm_runtime_enable(&pdev->dev);
> +
> /* unlock the device */
> zynq_fpga_write(priv, UNLOCK_OFFSET, UNLOCK_MASK);
>
> - clk_disable(priv->clk);
>
> err = fpga_mgr_register(dev, "Xilinx Zynq FPGA Manager",
> &zynq_fpga_ops, priv);
> if (err) {
> dev_err(dev, "unable to register FPGA manager");
> - clk_unprepare(priv->clk);
> + clk_disable_unprepare(priv->clk);
> + pm_runtime_put_noidle(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
> return err;
> }
>
> + pm_runtime_put(&pdev->dev);
> +
> return 0;
> }
>
> @@ -483,11 +490,45 @@ static int zynq_fpga_remove(struct platform_device *pdev)
>
> fpga_mgr_unregister(&pdev->dev);
>
> - clk_unprepare(priv->clk);
> + pm_runtime_get_sync(&pdev->dev);
> + clk_disable_unprepare(priv->clk);
> + pm_runtime_put_noidle(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
>
> return 0;
> }
>
> +static int __maybe_unused zynq_fpga_runtime_suspend(struct device *dev)
> +{
> + struct zynq_fpga_priv *priv;
> + struct fpga_manager *mgr;
> +
> + mgr = dev_get_drvdata(dev);
> + priv = mgr->priv;
> +
> + clk_disable(priv->clk);
From what I understand, this call is done in a sleepable context, so you can
use clk_disable_unprepare here (and its counterpart in resume). And remove the
prepare at probe time and unprepare at removal.
Not all clocks can implement atomic enable/disable, for example I2C and SPI
controlled clocks only implement the prepare/unprepare routines.
I guess the "clk" here will always be a SOC provided one, so it won't make any
difference for the Zynq, but someone is likely to some day copy/paste this
driver and use it for some externally connected FPGA instead.
> +
> + return 0;
> +}
> +
> +static int __maybe_unused zynq_fpga_runtime_resume(struct device *dev)
> +{
> + struct zynq_fpga_priv *priv;
> + struct fpga_manager *mgr;
> +
> + mgr = dev_get_drvdata(dev);
> + priv = mgr->priv;
> +
> + clk_enable(priv->clk);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops zynq_fpga_pm_ops = {
> + SET_RUNTIME_PM_OPS(zynq_fpga_runtime_suspend,
> + zynq_fpga_runtime_resume, NULL)
> +};
> +
> #ifdef CONFIG_OF
> static const struct of_device_id zynq_fpga_of_match[] = {
> { .compatible = "xlnx,zynq-devcfg-1.0", },
> @@ -503,6 +544,7 @@ static struct platform_driver zynq_fpga_driver = {
> .driver = {
> .name = "zynq_fpga_manager",
> .of_match_table = of_match_ptr(zynq_fpga_of_match),
> + .pm = &zynq_fpga_pm_ops,
> },
> };
>
>
Kind regards,
Mike Looijmans
System Expert
TOPIC Embedded Products
Eindhovenseweg 32-C, NL-5683 KH Best
Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
Telefax: +31 (0) 499 33 69 70
E-mail: mike.looijmans at topicproducts.com
Website: www.topicproducts.com
Please consider the environment before printing this e-mail
Visit us at : Aerospace Electrical Systems Expo Europe which will be held from 17.11.2015 till 19.11.2015, Findorffstrasse 101 Bremen, Germany, Hall 5, stand number C65
http://www.aesexpo.eu
More information about the linux-arm-kernel
mailing list