[PATCH v2 2/3] ARM: dts: enable clock support for Broadcom NSP

[Ray Jui]

On 11/19/2015 3:05 PM, Jon Mason wrote:
> Replace current device tree dummy clocks with real clock support for
> Broadcom Northstar Plus SoC
>
> Signed-off-by: Jon Mason <jonmason at broadcom.com>
> ---
>   arch/arm/boot/dts/bcm-nsp.dtsi | 77 +++++++++++++++++++++++++++++++++++-------
>   1 file changed, 64 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
> index b74438c..361c2a6 100644
> --- a/arch/arm/boot/dts/bcm-nsp.dtsi
> +++ b/arch/arm/boot/dts/bcm-nsp.dtsi
> @@ -32,6 +32,7 @@
>
>   #include <dt-bindings/interrupt-controller/arm-gic.h>
>   #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/clock/bcm-nsp.h>
>
>   #include "skeleton.dtsi"
>
> @@ -42,7 +43,7 @@
>
>   	mpcore {
>   		compatible = "simple-bus";
> -		ranges = <0x00000000 0x19020000 0x00003000>;
> +		ranges = <0x00000000 0x19000000 0x00023000>;
>   		#address-cells = <1>;
>   		#size-cells = <1>;
>
> @@ -58,16 +59,23 @@
>   			};
>   		};
>
> +		a9pll: arm_clk at 0000 {
> +			#clock-cells = <0>;
> +			compatible = "brcm,nsp-armpll";
> +			clocks = <&osc>;
> +			reg = <0x0000 0x1000>;
> +		};
> +
>   		timer at 0200 {

timer at 20200. Or is this addressed in another patch? I completely lose 
track of these....

>   			compatible = "arm,cortex-a9-global-timer";
> -			reg = <0x0200 0x100>;
> +			reg = <0x20200 0x100>;
>   			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
>   			clocks = <&periph_clk>;
>   		};
>
>   		twd-timer at 0600 {

twd-timer at 20600

>   			compatible = "arm,cortex-a9-twd-timer";
> -			reg = <0x0600 0x20>;
> +			reg = <0x20600 0x20>;
>   			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
>   						  IRQ_TYPE_LEVEL_HIGH)>;
>   			clocks = <&periph_clk>;
> @@ -75,7 +83,7 @@
>
>   		twd-watchdog at 0620 {

same here

>   			compatible = "arm,cortex-a9-twd-wdt";
> -			reg = <0x0620 0x20>;
> +			reg = <0x20620 0x20>;
>   			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
>   						  IRQ_TYPE_LEVEL_HIGH)>;
>   			clocks = <&periph_clk>;
> @@ -86,13 +94,13 @@
>   			#interrupt-cells = <3>;
>   			#address-cells = <0>;
>   			interrupt-controller;
> -			reg = <0x1000 0x1000>,
> -			      <0x0100 0x100>;
> +			reg = <0x21000 0x1000>,
> +			      <0x20100 0x100>;
>   		};
>
>   		L2: l2-cache {
>   			compatible = "arm,pl310-cache";
> -			reg = <0x2000 0x1000>;
> +			reg = <0x22000 0x1000>;
>   			cache-unified;
>   			cache-level = <2>;
>   		};
> @@ -103,10 +111,34 @@
>   		#size-cells = <1>;
>   		ranges;
>
> -		periph_clk: periph_clk {
> +		osc: oscillator {
> +			#clock-cells = <0>;
>   			compatible = "fixed-clock";
> +			clock-frequency = <25000000>;
> +		};
> +
> +		iprocmed: iprocmed {
> +			#clock-cells = <0>;
> +			compatible = "fixed-factor-clock";
> +			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> +			clock-div = <2>;
> +			clock-mult = <1>;
> +		};
> +
> +		iprocslow: iprocslow {
> +			#clock-cells = <0>;
> +			compatible = "fixed-factor-clock";
> +			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
> +			clock-div = <4>;
> +			clock-mult = <1>;
> +		};
> +
> +		periph_clk: periph_clk {
>   			#clock-cells = <0>;
> -			clock-frequency = <500000000>;
> +			compatible = "fixed-factor-clock";
> +			clocks = <&a9pll>;
> +			clock-div = <2>;
> +			clock-mult = <1>;
>   		};
>   	};
>
> @@ -118,17 +150,17 @@
>
>   		uart0: serial at 0300 {
>   			compatible = "ns16550a";
> -			reg = <0x0300 0x100>;
> +			reg = <0x000300 0x100>;
>   			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> -			clock-frequency = <62499840>;
> +			clocks = <&osc>;
>   			status = "disabled";
>   		};
>
>   		uart1: serial at 0400 {
>   			compatible = "ns16550a";
> -			reg = <0x0400 0x100>;
> +			reg = <0x000400 0x100>;
>   			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> -			clock-frequency = <62499840>;
> +			clocks = <&osc>;
>   			status = "disabled";
>   		};
>
> @@ -226,5 +258,24 @@
>   			interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
>   			clock-frequency = <100000>;
>   		};
> +
> +		lcpll0: lcpll0 at 3f100 {
> +			#clock-cells = <1>;
> +			compatible = "brcm,nsp-lcpll0";
> +			reg = <0x3f100 0x14>;
> +			clocks = <&osc>;
> +			clock-output-names = "lcpll0", "pcie_phy", "sdio",
> +					     "ddr_phy";
> +		};
> +
> +		genpll: genpll at 3f140 {
> +			#clock-cells = <1>;
> +			compatible = "brcm,nsp-genpll";
> +			reg = <0x3f140 0x24>;
> +			clocks = <&osc>;
> +			clock-output-names = "genpll", "phy", "ethernetclk",
> +					     "usbclk", "iprocfast", "sata1",
> +					     "sata2";
> +		};
>   	};
>   };
>