[PATCH v2] arm, am335x: add support for the bosch shc board
Dave Gerlach
d-gerlach at ti.com
Tue Nov 17 13:29:33 PST 2015
Hi,
On 11/17/2015 02:24 AM, Heiko Schocher wrote:
> add support for the am335x based shc board.
>
> UART: 0-2 and 4
> DRAM: 512 MiB
> MMC: OMAP SD/MMC: 0 @ 26 MHz
> OMAP SD/MMC: 1 @ 26 MHz
> I2C: at24 eeprom, pcf8563
> USB: USB1 (host)
>
> Signed-off-by: Heiko Schocher <hs at denx.de>
> ---
> The following patches are needed to get all working
> for the shc board:
> - disable clkout on pcf8563
> accepted.
> http://www.spinics.net/lists/devicetree/msg98542.html
>
> - leds: leds-gpio: add shutdown function
> accepted.
> https://lkml.org/lkml/2015/10/13/169
>
> - net: phy: smsc: disable energy detect mode
> accepted
> [PATCH v2 2/2] net: phy: smsc: disable energy detect mode
> https://lkml.org/lkml/2015/10/17/2
> [PATCH v2 1/2] drivers: net: cpsw: add phy-handle parsing
> https://lkml.org/lkml/2015/10/17/4
>
> - ARM: OMAP2+: omap_hwmod: Introduce ti,no-init dt property
> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/328204.html
> @Dave: What is the current state of this patch?
> I have the same problem here on this am335x based board
>
A different approach is being taken for resolving the issue of rtc hwmod
on am43x epos evm [1], which is what I was attempting to solve with the
patch you have linked. We decided to avoid changing omap_hwmod code and
I haven't been pursuing the ti,no-init flag anymore.
Regards,
Dave
[1] http://www.spinics.net/lists/linux-omap/msg121987.html
> - [PATCH v2] regulator: tps65217: remove tps65217.dtsi file
> http://www.kernelhub.org/?msg=868907&p=2
>
> - bootlog and automated tests:
> http://xeidos.ddns.net/buildbot/waterfall
>
> Changes in v2:
> - Use IOPAD pinmux macro as Robert Nelson
> suggested.
>
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/am335x-shc.dts | 577 +++++++++++++++++++++++++++++++++++++++
> 2 files changed, 579 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/am335x-shc.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 30bbc37..65d750f 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -466,7 +466,8 @@ dtb-$(CONFIG_SOC_AM33XX) += \
> am335x-pepper.dtb \
> am335x-lxm.dtb \
> am335x-chiliboard.dtb \
> - am335x-wega-rdk.dtb
> + am335x-wega-rdk.dtb \
> + am335x-shc.dtb
> dtb-$(CONFIG_ARCH_OMAP4) += \
> omap4-duovero-parlor.dtb \
> omap4-panda.dtb \
> diff --git a/arch/arm/boot/dts/am335x-shc.dts b/arch/arm/boot/dts/am335x-shc.dts
> new file mode 100644
> index 0000000..1b5b044
> --- /dev/null
> +++ b/arch/arm/boot/dts/am335x-shc.dts
> @@ -0,0 +1,577 @@
> +/*
> + * support for the bosch am335x based shc c3 board
> + *
> + * Copyright, C) 2015 Heiko Schocher <hs at denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +/dts-v1/;
> +
> +#include "am33xx.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Bosch SHC";
> + compatible = "ti,am335x-shc", "ti,am335x-bone", "ti,am33xx";
> +
> + aliases {
> + mmcblk0 = &mmc1;
> + mmcblk1 = &mmc2;
> + };
> +
> + cpus {
> + cpu at 0 {
> + /*
> + * To consider voltage drop between PMIC and SoC,
> + * tolerance value is reduced to 2% from 4% and
> + * voltage value is increased as a precaution.
> + */
> + operating-points = <
> + /* kHz uV */
> + 594000 1225000
> + 294000 1125000
> + >;
> + voltage-tolerance = <2>; /* 2 percentage */
> + cpu0-supply = <&dcdc2_reg>;
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> +
> + back_button {
> + label = "Back Button";
> + gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
> + linux,code = <KEY_BACK>;
> + debounce-interval = <1000>;
> + gpio-key,wakeup;
> + };
> +
> + front_button {
> + label = "Front Button";
> + gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
> + linux,code = <KEY_FRONT>;
> + debounce-interval = <1000>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + leds {
> + pinctrl-names = "default";
> + pinctrl-0 = <&user_leds_s0>;
> +
> + compatible = "gpio-leds";
> +
> + led at 1 {
> + label = "shc:power:red";
> + gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led at 2 {
> + label = "shc:power:bl";
> + gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "timer";
> + default-state = "on";
> + };
> +
> + led at 3 {
> + label = "shc:lan:red";
> + gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led at 4 {
> + label = "shc:lan:bl";
> + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led at 5 {
> + label = "shc:cloud:red";
> + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led at 6 {
> + label = "shc:cloud:bl";
> + gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x80000000 0x20000000>; /* 512 MB */
> + };
> +
> + vmmcsd_fixed: fixedregulator at 0 {
> + compatible = "regulator-fixed";
> + regulator-name = "vmmcsd_fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +};
> +
> +&aes {
> + status = "okay";
> +};
> +
> +&cppi41dma {
> + status = "okay";
> +};
> +
> +&davinci_mdio {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&davinci_mdio_default>;
> + pinctrl-1 = <&davinci_mdio_sleep>;
> + status = "okay";
> +
> + ethernetphy0: ethernet-phy at 0 {
> + reg = <0>;
> + smsc,disable-energy-detect;
> + };
> +};
> +
> +&epwmss1 {
> + status = "okay";
> +
> + ehrpwm1: ehrpwm at 48302200 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ehrpwm1_pins>;
> + status = "okay";
> + };
> +};
> +
> +&gpio1 {
> + hmtc_rst {
> + gpio-hog;
> + gpios = <24 GPIO_ACTIVE_LOW>;
> + output-high;
> + line-name = "homematic_reset";
> + };
> +
> + hmtc_prog {
> + gpio-hog;
> + gpios = <27 GPIO_ACTIVE_LOW>;
> + output-high;
> + line-name = "homematic_program";
> + };
> +};
> +
> +&gpio3 {
> + zgb_rst {
> + gpio-hog;
> + gpios = <18 GPIO_ACTIVE_LOW>;
> + output-low;
> + line-name = "zigbee_reset";
> + };
> +
> + zgb_boot {
> + gpio-hog;
> + gpios = <19 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "zigbee_boot";
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + tps: tps at 24 {
> + reg = <0x24>;
> + };
> +
> + at24 at 50 {
> + compatible = "at24,24c32";
> + pagesize = <32>;
> + reg = <0x50>;
> + };
> +
> + pcf8563 at 51 {
> + compatible = "nxp,pcf8563";
> + reg = <0x51>;
> + };
> +};
> +
> +&mac {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&cpsw_default>;
> + pinctrl-1 = <&cpsw_sleep>;
> + status = "okay";
> + slaves = <1>;
> + cpsw_emac0: slave at 4a100200 {
> + phy_id = <&davinci_mdio>, <0>;
> + phy-mode = "mii";
> + phy-handle = <ðernetphy0>;
> + };
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + bus-width = <0x4>;
> + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> + max-frequency = <26000000>;
> + vmmc-supply = <&vmmcsd_fixed>;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_pins>;
> + bus-width = <8>;
> + max-frequency = <26000000>;
> + sd-uhs-sdr25;
> + vmmc-supply = <&vmmcsd_fixed>;
> + status = "okay";
> +};
> +
> +&mmc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc3_pins>;
> + bus-width = <4>;
> + cap-power-off-card;
> + max-frequency = <26000000>;
> + sd-uhs-sdr25;
> + vmmc-supply = <&vmmcsd_fixed>;
> + status = "okay";
> +};
> +
> +&rtc {
> + ti,no-init;
> +};
> +
> +&sham {
> + status = "okay";
> +};
> +
> +&tps {
> + compatible = "ti,tps65217";
> + ti,pmic-shutdown-controller;
> +
> + regulators {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dcdc1_reg: regulator at 0 {
> + reg = <0>;
> + regulator-name = "vdds_dpr";
> + regulator-compatible = "dcdc1";
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + dcdc2_reg: regulator at 1 {
> + reg = <1>;
> + /*
> + * VDD_MPU voltage limits 0.95V - 1.26V with
> + * +/-4% tolerance
> + */
> + regulator-compatible = "dcdc2";
> + regulator-name = "vdd_mpu";
> + regulator-min-microvolt = <925000>;
> + regulator-max-microvolt = <1375000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <70000>;
> + };
> +
> + dcdc3_reg: regulator at 2 {
> + reg = <2>;
> + /*
> + * VDD_CORE voltage limits 0.95V - 1.1V with
> + * +/-4% tolerance
> + */
> + regulator-name = "vdd_core";
> + regulator-compatible = "dcdc3";
> + regulator-min-microvolt = <925000>;
> + regulator-max-microvolt = <1125000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: regulator at 3 {
> + reg = <3>;
> + regulator-name = "vio,vrtc,vdds";
> + regulator-compatible = "ldo1";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: regulator at 4 {
> + reg = <4>;
> + regulator-name = "vdd_3v3aux";
> + regulator-compatible = "ldo2";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: regulator at 5 {
> + reg = <5>;
> + regulator-name = "vdd_1v8";
> + regulator-compatible = "ldo3";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: regulator at 6 {
> + reg = <6>;
> + regulator-name = "vdd_3v3a";
> + regulator-compatible = "ldo4";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins>;
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_ctrl_mod {
> + status = "okay";
> +};
> +
> +&usb1_phy {
> + status = "okay";
> +};
> +
> +&usb1 {
> + status = "okay";
> + dr_mode = "host";
> +};
> +
> +&am33xx_pinmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&clkout2_pin>;
> +
> + clkout2_pin: pinmux_clkout2_pin {
> + pinctrl-single,pins = <
> + /* xdma_event_intr1.clkout2 */
> + AM33XX_IOPAD(0x9b4, PIN_INPUT | MUX_MODE6)
> + >;
> + };
> +
> + cpsw_default: cpsw_default {
> + pinctrl-single,pins = <
> + /* Slave 1 */
> + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0)
> + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + >;
> + };
> +
> + cpsw_sleep: cpsw_sleep {
> + pinctrl-single,pins = <
> + /* Slave 1 reset value */
> + AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + davinci_mdio_default: davinci_mdio_default {
> + pinctrl-single,pins = <
> + /* mdio_data.mdio_data */
> + AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
> + /* mdio_clk.mdio_clk */
> + AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)
> + >;
> + };
> +
> + davinci_mdio_sleep: davinci_mdio_sleep {
> + pinctrl-single,pins = <
> + /* MDIO reset value */
> + AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + >;
> + };
> +
> + ehrpwm1_pins: pinmux_ehrpwm1 {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE6) /* gpmc_a3.gpio1_19 */
> + >;
> + };
> +
> + emmc_pins: pinmux_emmc_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x880, PIN_INPUT | MUX_MODE2)
> + AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2)
> + AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1)
> + AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1)
> + >;
> + };
> +
> + i2c0_pins: pinmux_i2c0_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x988, PIN_INPUT | MUX_MODE0)
> + AM33XX_IOPAD(0x98c, PIN_INPUT | MUX_MODE0)
> + >;
> + };
> +
> + mmc1_pins: pinmux_mmc1_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE5)
> + >;
> + };
> +
> + mmc3_pins: pinmux_mmc3_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x830, PIN_INPUT | MUX_MODE3)
> + AM33XX_IOPAD(0x834, PIN_INPUT | MUX_MODE3)
> + AM33XX_IOPAD(0x838, PIN_INPUT | MUX_MODE3)
> + AM33XX_IOPAD(0x83c, PIN_INPUT | MUX_MODE3)
> + AM33XX_IOPAD(0x888, PIN_INPUT | MUX_MODE3)
> + AM33XX_IOPAD(0x88c, PIN_INPUT | MUX_MODE3)
> + >;
> + };
> +
> + uart0_pins: pinmux_uart0_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x968, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x96c, PIN_OUTPUT | MUX_MODE0)
> + AM33XX_IOPAD(0x970, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x974, PIN_OUTPUT | MUX_MODE0)
> + >;
> + };
> +
> + uart1_pins: pinmux_uart1 {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x978, PIN_INPUT_PULLDOWN | MUX_MODE0)
> + AM33XX_IOPAD(0x97C, PIN_OUTPUT | MUX_MODE0)
> + AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE0)
> + AM33XX_IOPAD(0x984, PIN_OUTPUT | MUX_MODE0)
> + >;
> + };
> +
> + uart2_pins: pinmux_uart2_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE1)
> + AM33XX_IOPAD(0x954, PIN_OUTPUT | MUX_MODE1)
> + >;
> + };
> +
> + uart4_pins: pinmux_uart4_pins {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6)
> + AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLUP | MUX_MODE6)
> + >;
> + };
> +
> + user_leds_s0: user_leds_s0 {
> + pinctrl-single,pins = <
> + AM33XX_IOPAD(0x820, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x824, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x82c, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x844, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x85c, PIN_OUTPUT_PULLUP | MUX_MODE7)
> + AM33XX_IOPAD(0x860, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x864, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x868, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x86c, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x878, PIN_OUTPUT_PULLUP | MUX_MODE7)
> + AM33XX_IOPAD(0x87c, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x894, PIN_INPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8e0, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8e4, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8e8, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x8ec, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x958, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x95c, PIN_OUTPUT | MUX_MODE7)
> + AM33XX_IOPAD(0x964, PIN_OUTPUT_PULLUP | MUX_MODE7)
> + AM33XX_IOPAD(0x9a0, PIN_OUTPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x9a8, PIN_INPUT_PULLDOWN | MUX_MODE7)
> + AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLUP | MUX_MODE7)
> + >;
> + };
> +};
>
More information about the linux-arm-kernel
mailing list