[PATCH v2 0/8] phy: rockchip-usb: correct pll handling and usb-uart

[Doug Anderson]

Heiko,

On Sun, Nov 8, 2015 at 8:04 AM, Heiko Stuebner <heiko at sntech.de> wrote:
> changes in v2:
> - add Doug's review-tag to patches 1 and 3
> - address comment and add the missing transistional rk_phy->base
>   assignment in patch2
>
>
> Patches 1-7 fix a long-standing issue with the clock-tree of Rockchip SoCs
> namely our ignorance of the usbphy-internal pll that creates the needed
> 480MHz but is also a supply-clock back to the core clock-controller in
> Rockchip SoCs.
>
> Till now that was worked around using a virtual clock in the cru itself,
> but that is of course ignorant of other parts then disabling the phy
> behind the cru's back, thus breaking potential users of these clocks.
>
>
> Patch 8, while not associated with the new pll handling, also builds
> on the groundwork introduced there and adds support for the function
> repurposing one of the phys as passthrough for uart-data. This enables
> attaching a ttl converter to the D+ and D- pins of an usb cable to
> receive uart data this way, when it is not really possible to attach
> a regular serial console to a board.
>
> One point of critique in my first iteration [0] of this was, that
> due to when the reconfiguration happens we may miss parts of the logs
> when earlycon is enabled. So far early_initcall gets used as the
> unflattened devicetree is necessary to set this up. Doing this for
> example in the early_param directly would require parsing the flattened
> devicetree to get needed nodes and properties.
>
> I still maintain that if you're working on anything before smp-bringup
> you should use a real dev-board instead or try to solder uart cables
> on hopefully available test-points :-) .
>
>
> In any case, if patch 8 causes to much headache, it could be dropped
> to not hinder the earlier 7 patches.
>
> [0] http://comments.gmane.org/gmane.linux.ports.arm.rockchip/715
>
> Heiko Stuebner (8):
>   phy: rockchip-usb: fix clock get-put mismatch
>   phy: rockchip-usb: introduce a common data-struct for the device
>   phy: rockchip-usb: move per-phy init into a separate function
>   phy: rockchip-usb: expose the phy-internal PLLs
>   clk: rockchip: fix usbphy-related clocks
>   ARM: dts: rockchip: add clock-cells for usb phy nodes
>   ARM: dts: rockchip: assign usbphy480m_src to the new usbphy pll on
>     veyron
>   phy: rockchip-usb: add handler for usb-uart functionality
>
>  .../devicetree/bindings/phy/rockchip-usb-phy.txt   |   6 +-
>  Documentation/kernel-parameters.txt                |   6 +
>  arch/arm/boot/dts/rk3066a.dtsi                     |   2 +
>  arch/arm/boot/dts/rk3188.dtsi                      |   2 +
>  arch/arm/boot/dts/rk3288-veyron.dtsi               |   2 +-
>  arch/arm/boot/dts/rk3288.dtsi                      |   3 +
>  drivers/clk/rockchip/clk-rk3188.c                  |  11 +-
>  drivers/clk/rockchip/clk-rk3288.c                  |  16 +-
>  drivers/phy/phy-rockchip-usb.c                     | 449 ++++++++++++++++++---
>  9 files changed, 416 insertions(+), 81 deletions(-)

If you happened to be in the mood for cleaning up this PHY and wanted
to fix up one more thing that I noticed...

...you could actually increase the range of registers managed by the
PHYs.  For instance, in rk3288, the "host1" port isn't just managed by
1 register, but by 4 (GRF_UOC2_CON0 - GRF_UOC2_CON3).  I think there
are 5 for the OTG port.

Obviously not required for this series and there's no (current) reason
to do anything with the rest of those registers, but it might be
interesting for the future...

-Doug