[PATCH v4 0/4] Add support for STM32 DMA

[M'boumba Cedric Madianga]

 Hi Vinod,

Do you have any further comments or suggestions on this serie ?

BR,
Cedric

2015-10-16 15:59 GMT+02:00 M'boumba Cedric Madianga <cedric.madianga at gmail.com>:
> This patchset adds support for the STM32 DMA controller.
> This controller provides 8 channels dedicated to managing memory access
> request from one or more peripherals.
> Each stream can have up to 8 requests in total.
>
> Changes since v3:
>  - Fix regression introduced in v3 during request channel
>  - Fix regression introduced in v3 for cyclic mode dma transfer
>  - update interrupt description in DT
>  - remove half transfer interrupt management as client callback as to be
>    called only for complete transfer
>
> Changes since v2:
>  - remove interrupt configuration management from DT (Mark)
>  - remove FIFO configuration management from DT except threshold as it is very
>    hard to handle it in the driver due to many possible combinations according
>    to burst and bus width (Mark)
>  - update DMA client message in DT documentation file
>  - specify the order to be used to set per-channel DMA interrupts in the DT
>    (Mark)
>  - remove unused enumerations for channel and request ids (Daniel)
>  - keep as soon as possible 80 lines char for more readability (Vinod)
>  - replace unsigned int by u32 (Vinod)
>  - use GFP_NOWAIT instead of GFP_ATOMIC during dma descriptors allocation
>    (Vinod)
>  - return error if burst is not supported in stm32_dma_get_burst() (Vinod)
>  - return error if bus_width is not supported in stm32_dma_get_width() (Vinod)
>  - add FIFO configuration management inside the driver except for threshold
>  - add interrupt configuration management inside the driver (Mark)
>  - rework stm32_dma_chan_irq() to handle error interrupt in one way (Vinod)
>  - rework stm32_dma_set_xfer_param() to be easier to read
>  - update stm32_dma_tx_status() to always return status from dma_cookie_status() (Vinod)
>  - disable clk if we don't manage to stop the DMA channel during channel
>    resources allocation (Daniel)
>  - set driver as built-in as DMA will be required by other built-in driver
>
>  Changes since v1:
>   - remove dmamux boolean as it is not needed
>   - replace dma by DMA in Kconfig (Maxime)
>   - add default return value in stm32_dma_get_width()
>   - add defalut return value in stm32_dma_get_burst()
>   - use lower case for constant hexadecimal values (Maxime)
>
> M'boumba Cedric Madianga (4):
>   dt-bindings: Document the STM32 DMA bindings
>   dmaengine: Add STM32 DMA driver
>   ARM: dts: Add STM32 DMA support for STM32F429 MCU
>   ARM: configs: Add STM32 DMA support in STM32 defconfig
>
>  .../devicetree/bindings/dma/stm32-dma.txt          |   82 ++
>  arch/arm/boot/dts/stm32f429.dtsi                   |   31 +
>  arch/arm/configs/stm32_defconfig                   |    2 +
>  drivers/dma/Kconfig                                |   12 +
>  drivers/dma/Makefile                               |    1 +
>  drivers/dma/stm32-dma.c                            | 1141 ++++++++++++++++++++
>  6 files changed, 1269 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/dma/stm32-dma.txt
>  create mode 100644 drivers/dma/stm32-dma.c
>
> --
> 1.9.1
>