[PATCH v5 1/1] ARM: mvebu: dts: Add dts file for DLink DNS-327L
Gregory CLEMENT
gregory.clement at free-electrons.com
Wed May 27 03:01:39 PDT 2015
Hi Andrew,
On 26/05/2015 17:50, Andrew Lunn wrote:
> On Tue, May 26, 2015 at 06:51:11PM +0300, Andrew Andrianov wrote:
>> DNS-327L is a 2-bay NAS with the following specs:
>> - 512MiB RAM
>> - 128MiB NAND Flash
>> - 1 GbE interface (Marvell PHY)
>> - 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
>> - 2 internal SATA ports handled by the Armada 370:
>> uses 2 gpios for power control
>> - two front 2-color leds (amber + white) for both discs,
>> controlled by the SoC
>> - One white LED handled by SoC (USB)
>> - 3 buttons. Power handled by weltrend, USB and
>> RESET (on the bottom) are wired via GPIOs
>> - Unidentified i2c device at address 0x13 (via i2cdetect)
>> - UART0 providing serial console
>> - Weltrend MCU serving for RTC, temperature, fan control,
>> and power button handling interfaced via UART1
>> (Handled via userspace dns320l-daemon)
>>
>> Signed-off-by: Andrew Andrianov <andrew at ncrmnt.org>
>> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
>
> Acked-by: Andrew Lunn <andrew at lunn.ch>
applied on mvebu/dt
Thanks,
Gregory
>
> Andrew
>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/armada-370-dlink-dns327l.dts | 357 +++++++++++++++++++++++++
>> 2 files changed, 358 insertions(+)
>> create mode 100644 arch/arm/boot/dts/armada-370-dlink-dns327l.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 86217db..58fa9f6 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -624,6 +624,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
>> zynq-zybo.dtb
>> dtb-$(CONFIG_MACH_ARMADA_370) += \
>> armada-370-db.dtb \
>> + armada-370-dlink-dns327l.dtb \
>> armada-370-mirabox.dtb \
>> armada-370-netgear-rn102.dtb \
>> armada-370-netgear-rn104.dtb \
>> diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
>> new file mode 100644
>> index 0000000..af4dc54
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
>> @@ -0,0 +1,357 @@
>> +/*
>> + * Device Tree file for D-Link DNS-327L
>> + *
>> + * Copyright (C) 2015, Andrew Andrianov <andrew at ncrmnt.org>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/* Remaining unsolved:
>> + * There's still some unknown device on i2c address 0x13
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include "armada-370.dtsi"
>> +
>> +/ {
>> + model = "D-Link DNS-327L";
>> + compatible = "dlink,dns327l",
>> + "marvell,armada370",
>> + "marvell,armada-370-xp";
>> +
>> + chosen {
>> + stdout-path = &uart0;
>> + };
>> +
>> + memory {
>> + device_type = "memory";
>> + reg = <0x00000000 0x20000000>; /* 512 MiB */
>> + };
>> +
>> + soc {
>> + ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
>> + MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
>> +
>> + pcie-controller {
>> + status = "okay";
>> +
>> + pcie at 1,0 {
>> + /* Port 0, Lane 0 */
>> + status = "okay";
>> + };
>> +
>> + pcie at 2,0 {
>> + /* Port 1, Lane 0 */
>> + status = "okay";
>> + };
>> + };
>> +
>> + internal-regs {
>> + sata at a0000 {
>> + nr-ports = <2>;
>> + status = "okay";
>> + };
>> +
>> + usb at 50000 {
>> + status = "okay";
>> + };
>> +
>> + nand at d0000 {
>> + status = "okay";
>> + num-cs = <1>;
>> + marvell,nand-keep-config;
>> + marvell,nand-enable-arbiter;
>> + nand-on-flash-bbt;
>> + nand-ecc-strength = <4>;
>> + nand-ecc-step-size = <512>;
>> +
>> + partition at 0 {
>> + label = "u-boot";
>> + /* 1.0 MiB */
>> + reg = <0x0000000 0x100000>;
>> + read-only;
>> + };
>> +
>> + partition at 100000 {
>> + label = "u-boot-env";
>> + /* 128 KiB */
>> + reg = <0x100000 0x20000>;
>> + read-only;
>> + };
>> +
>> + partition at 120000 {
>> + label = "uImage";
>> + /* 7 MiB */
>> + reg = <0x120000 0x700000>;
>> + };
>> +
>> + partition at 820000 {
>> + label = "ubifs";
>> + /* ~ 84 MiB */
>> + reg = <0x820000 0x54e0000>;
>> + };
>> +
>> + /* Hardcoded into stock bootloader */
>> + partition at 5d00000 {
>> + label = "failsafe-uImage";
>> + /* 5 MiB */
>> + reg = <0x5d00000 0x500000>;
>> + };
>> +
>> + partition at 6200000 {
>> + label = "failsafe-fs";
>> + /* 29 MiB */
>> + reg = <0x6200000 0x1d00000>;
>> + };
>> +
>> + partition at 7f00000 {
>> + label = "bbt";
>> + /* 1 MiB for BBT */
>> + reg = <0x7f00000 0x100000>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> + pinctrl-0 = <
>> + &backup_button_pin
>> + &power_button_pin
>> + &reset_button_pin>;
>> + pinctrl-names = "default";
>> +
>> + power-button {
>> + label = "Power Button";
>> + linux,code = <KEY_POWER>;
>> + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + backup-button {
>> + label = "Backup Button";
>> + linux,code = <KEY_COPY>;
>> + gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + reset-button {
>> + label = "Reset Button";
>> + linux,code = <KEY_RESTART>;
>> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> + pinctrl-0 = <
>> + &sata_l_amber_pin
>> + &sata_r_amber_pin
>> + &backup_led_pin
>> + /* Ensure these are managed by hardware */
>> + &sata_l_white_pin
>> + &sata_r_white_pin>;
>> +
>> + pinctrl-names = "default";
>> +
>> + sata-r-amber-pin {
>> + label = "dns327l:amber:sata-r";
>> + gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
>> + default-state = "keep";
>> + };
>> +
>> + sata-l-amber-pin {
>> + label = "dns327l:amber:sata-l";
>> + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
>> + default-state = "keep";
>> + };
>> +
>> + backup-led-pin {
>> + label = "dns327l:white:usb";
>> + gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
>> + default-state = "keep";
>> + };
>> + };
>> +
>> + regulators {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + usb_power: regulator at 1 {
>> + compatible = "regulator-fixed";
>> + reg = <1>;
>> + pinctrl-0 = <&xhci_pwr_pin>;
>> + pinctrl-names = "default";
>> + regulator-name = "USB3.0 Port Power";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + enable-active-high;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + sata_r_power: regulator at 2 {
>> + compatible = "regulator-fixed";
>> + reg = <2>;
>> + pinctrl-0 = <&sata_r_pwr_pin>;
>> + pinctrl-names = "default";
>> + regulator-name = "SATA-R Power";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + startup-delay-us = <2000000>;
>> + enable-active-high;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + sata_l_power: regulator at 3 {
>> + compatible = "regulator-fixed";
>> + reg = <3>;
>> + pinctrl-0 = <&sata_l_pwr_pin>;
>> + pinctrl-names = "default";
>> + regulator-name = "SATA-L Power";
>> + regulator-min-microvolt = <5000000>;
>> + regulator-max-microvolt = <5000000>;
>> + startup-delay-us = <4000000>;
>> + enable-active-high;
>> + regulator-always-on;
>> + regulator-boot-on;
>> + gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
>> + };
>> + };
>> +};
>> +
>> +&pinctrl {
>> + sata_l_white_pin: sata-l-white-pin {
>> + marvell,pins = "mpp57";
>> + marvell,function = "sata0";
>> + };
>> +
>> + sata_r_white_pin: sata-r-white-pin {
>> + marvell,pins = "mpp55";
>> + marvell,function = "sata1";
>> + };
>> +
>> + sata_r_amber_pin: sata-r-amber-pin {
>> + marvell,pins = "mpp52";
>> + marvell,function = "gpio";
>> + };
>> +
>> + sata_l_amber_pin: sata-l-amber-pin {
>> + marvell,pins = "mpp53";
>> + marvell,function = "gpio";
>> + };
>> +
>> + backup_led_pin: backup-led-pin {
>> + marvell,pins = "mpp61";
>> + marvell,function = "gpo";
>> + };
>> +
>> + xhci_pwr_pin: xhci-pwr-pin {
>> + marvell,pins = "mpp13";
>> + marvell,function = "gpio";
>> + };
>> +
>> + sata_r_pwr_pin: sata-r-pwr-pin {
>> + marvell,pins = "mpp54";
>> + marvell,function = "gpio";
>> + };
>> +
>> + sata_l_pwr_pin: sata-l-pwr-pin {
>> + marvell,pins = "mpp56";
>> + marvell,function = "gpio";
>> + };
>> +
>> + uart1_pins: uart1-pins {
>> + marvell,pins = "mpp60", "mpp61";
>> + marvell,function = "uart1";
>> + };
>> +
>> + power_button_pin: power-button-pin {
>> + marvell,pins = "mpp65";
>> + marvell,function = "gpio";
>> + };
>> +
>> + backup_button_pin: backup-button-pin {
>> + marvell,pins = "mpp63";
>> + marvell,function = "gpio";
>> + };
>> +
>> + reset_button_pin: reset-button-pin {
>> + marvell,pins = "mpp64";
>> + marvell,function = "gpio";
>> + };
>> +};
>> +
>> +/* Serial console */
>> +&uart0 {
>> + status = "okay";
>> +};
>> +
>> +/* Connected to Weltrend MCU */
>> +&uart1 {
>> + pinctrl-0 = <&uart1_pins>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> +};
>> +
>> +&mdio {
>> + phy0: ethernet-phy at 0 { /* Marvell 88E1318 */
>> + reg = <0>;
>> + marvell,reg-init = <0x0 0x16 0x0 0x0002>,
>> + <0x0 0x19 0x0 0x0077>,
>> + <0x0 0x18 0x0 0x5747>;
>> + };
>> +};
>> +
>> +ð1 {
>> + phy = <&phy0>;
>> + phy-mode = "rgmii-id";
>> + status = "okay";
>> +};
>> +
>> +&i2c0 {
>> + compatible = "marvell,mv64xxx-i2c";
>> + clock-frequency = <100000>;
>> + status = "okay";
>> +};
>> --
>> 2.1.4
>>
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
More information about the linux-arm-kernel
mailing list