[PATCH v4 1/7] mmc: dt-bindings: add Mediatek MMC bindings

[Chaotian Jing]

Dear Ulf,

Thanks for your review!
Please see my comment:
On Tue, 2015-05-19 at 11:41 +0200, Ulf Hansson wrote:
> On 19 May 2015 at 08:36, Chaotian Jing <chaotian.jing at mediatek.com> wrote:
> > Document the device-tree binding of Mediatek MMC host
> >
> > Signed-off-by: Chaotian Jing <chaotian.jing at mediatek.com>
> > ---
> >  Documentation/devicetree/bindings/mmc/mtk-sd.txt | 33 ++++++++++++++++++++++++
> >  1 file changed, 33 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/mmc/mtk-sd.txt
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> > new file mode 100644
> > index 0000000..ba6d668
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> > @@ -0,0 +1,33 @@
> > +* MTK MMC controller
> > +
> > +The MTK  MSDC can act as a MMC controller
> > +to support MMC, SD, and SDIO types of memory cards.
> > +
> > +This file documents differences between the core properties in mmc.txt
> > +and the properties used by the msdc driver.
> > +
> > +Required properties:
> > +- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc".
> > +- interrupts: Should contain MSDC interrupt number
> > +- clocks: MSDC source clock, HCLK, HCLK is mandatory when it is not controlled by Infra
> 
> This seems strange. Either it's mandatory since it's under the
> "Required properties" section or it should be moved to the "Optional
> properties" section.
> 
Yes, as you see, the "HCLK" is mandatory for MSDC0 & MSDC3, but MSDC1 &
MSDC2 do not have corresponding HCLK.
By the way, I will make the vqmmc-supply to mandatory, As the pinctrl
select depend on it.
> > +- clock-names: "source", "hclk"
> > +- pinctrl-names: should be "default", "state_uhs"
> > +- pinctrl-0: should contain default/high speed pin ctrl
> > +- pinctrl-1: should contain uhs mode pin ctrl
> > +- vmmc-supply: power to the Core
> > +
> > +Optional properties:
> > +- vqmmc-supply: power to the IO(for SD/SDIO)
> > +
> > +Examples:
> > +mmc0: mmc at 11230000 {
> > +       compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc";
> > +       reg = <0 0x11230000 0 0x108>;
> > +       interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
> > +       vmmc-supply = <&mt6397_vemc_3v3_reg>;
> > +       clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
> > +       clock-names = "source", "hclk";
> > +       pinctrl-names = "default", "state_uhs";
> > +       pinctrl-0 = <&mmc0_pins_default>;
> > +       pinctrl-1 = <&mmc0_pins_uhs>;
> > +};
> > --
> > 1.8.1.1.dirty
> >
> 
> Kind regards
> Uffe