[PATCH v5 1/3] drm/layerscape: Add Freescale DCU DRM driver
Wang J.W.
Jianwei.Wang at freescale.com
Wed May 20 19:47:16 PDT 2015
Hi Dave,
Can you help me review this patch please? Thanks.
Jianwei
> -----Original Message-----
> From: Wang Jianwei-B52261
> Sent: Thursday, May 07, 2015 2:29 PM
> To: Wang Jianwei-B52261; airlied at linux.ie; daniel.vetter at intel.com;
> stefan at agner.ch; Wood Scott-B07421; dri-devel at lists.freedesktop.org
> Cc: linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> Jin Zhengxiong-R64188; Wang Huan-B18965; Xiubo Li
> Subject: RE: [PATCH v5 1/3] drm/layerscape: Add Freescale DCU DRM driver
>
> Hi Dave,
>
> Can you help me to review this patch? Thanks.
>
> Jianwei
>
> > -----Original Message-----
> > From: Jianwei Wang [mailto:jianwei.wang at freescale.com]
> > Sent: Friday, April 17, 2015 2:36 PM
> > To: airlied at linux.ie; daniel.vetter at intel.com; stefan at agner.ch; Wood
> > Scott-B07421; dri-devel at lists.freedesktop.org
> > Cc: linux-kernel at vger.kernel.org; linux-arm-kernel at lists.infradead.org;
> > Jin Zhengxiong-R64188; Wang Jianwei-B52261; Wang Huan-B18965; Xiubo Li;
> > Wang Jianwei-B52261
> > Subject: [PATCH v5 1/3] drm/layerscape: Add Freescale DCU DRM driver
> >
> > From: Jianwei Wang <b52261 at freescale.com>
> >
> > This patch add support for Two Dimensional Animation and Compositing
> > Engine (2D-ACE) on the Freescale SoCs.
> >
> > 2D-ACE is a Freescale display controller. 2D-ACE describes the
> > functionality of the module extremely well its name is a value that
> cannot
> > be used as a token in programming languages.
> > Instead the valid token "DCU" is used to tag the register names and
> > function names.
> >
> > The Display Controller Unit (DCU) module is a system master that fetches
> > graphics stored in internal or external memory and displays them on a
> TFT
> > LCD panel. A wide range of panel sizes is supported and the timing of
> the
> > interface signals is highly configurable.
> > Graphics are read directly from memory and then blended in real-time,
> > which allows for dynamic content creation with minimal CPU intervention.
> >
> > The features:
> > (1) Full RGB888 output to TFT LCD panel.
> > (2) For the current LCD panel, WQVGA "480x272" is supported.
> > (3) Blending of each pixel using up to 4 source layers dependent on size
> > of panel.
> > (4) Each graphic layer can be placed with one pixel resolution in either
> > axis.
> > (5) Each graphic layer support RGB565 and RGB888 direct colors without
> > alpha channel and BGRA8888 BGRA4444 ARGB1555 direct colors with an alpha
> > channel and YUV422 format.
> > (6) Each graphic layer support alpha blending with 8-bit resolution.
> >
> > This is a simplified version, only one primary plane, one framebuffer
> > created for fbdev, one crtc, one connector for TFT LCD panel, an encoder.
> >
> > Signed-off-by: Alison Wang <b18965 at freescale.com>
> > Signed-off-by: Xiubo Li <lixiubo at cmss.chinamobile.com>
> > Signed-off-by: Jianwei Wang <jianwei.wang at freescale.com>
> > ---
> >
> > Changed in V5
> >
> > - Update commit message
> > - Add layer registers initialization
> > - Remove unused functions
> > - Rename driver folder
> > - Move pixel clock control functions to fsl_dcu_drm_drv.c
> > - remove redundant enable the clock implicitly using regmap
> > - Add maintainer message
> >
> > Changed in V4:
> >
> > -This version doesn't have functionality changed Just a minor
> adjustment.
> >
> > Changed in V3:
> >
> > - Test driver on Vybrid board and add compatible string
> > - Remove unused functions
> > - set default crtc for encoder
> > - replace legacy functions with atomic help functions
> > - Set the unique name of the DRM device
> > - Implement irq handle function for vblank interrupt
> >
> > Changed in v2:
> > - Add atomic support
> > - Modify bindings file
> > - Rename node for compatibility
> > - Move platform related code out for compatibility
> >
> > .../devicetree/bindings/drm/fsl-dcu/fsl,dcu.txt | 50 +++
> > MAINTAINERS | 8 +
> > drivers/gpu/drm/Kconfig | 2 +
> > drivers/gpu/drm/Makefile | 1 +
> > drivers/gpu/drm/fsl-dcu/Kconfig | 17 +
> > drivers/gpu/drm/fsl-dcu/Makefile | 7 +
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.c | 194 +++++++++++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.h | 30 ++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.c | 172 ++++++++++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.h | 22 ++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c | 373
> > +++++++++++++++++++++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h | 223 ++++++++++++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_fbdev.c | 26 ++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.c | 42 +++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.h | 17 +
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.c | 192 +++++++++++
> > drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.h | 23 ++
> > 17 files changed, 1399 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/drm/fsl-
> > dcu/fsl,dcu.txt
> > create mode 100644 drivers/gpu/drm/fsl-dcu/Kconfig create mode 100644
> > drivers/gpu/drm/fsl-dcu/Makefile create mode 100644
> drivers/gpu/drm/fsl-
> > dcu/fsl_dcu_drm_connector.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.h
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.h
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_fbdev.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.h
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.c
> > create mode 100644 drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.h
> >
> > diff --git a/Documentation/devicetree/bindings/drm/fsl-dcu/fsl,dcu.txt
> > b/Documentation/devicetree/bindings/drm/fsl-dcu/fsl,dcu.txt
> > new file mode 100644
> > index 0000000..bdc7d5b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/drm/fsl-dcu/fsl,dcu.txt
> > @@ -0,0 +1,49 @@
> > +Device Tree bindings for Freescale DCU DRM Driver
> > +
> > +Required properties:
> > +- compatible: Should be one of
> > + * "fsl,ls1021a-dcu".
> > + * "fsl,vf610-dcu".
> > +- reg: Address and length of the register set for dcu.
> > +- clocks: From common clock binding: handle to dcu clock.
> > +- clock-names: From common clock binding: Shall be "dcu".
> > +- display: The phandle to display node.
> > +
> > +Required properties:
> > +- bits-per-pixel: <16> for RGB565,
> > + <24> for RGB888,
> > + <32> for RGB8888.
> > +
> > +Required timing node for dispplay sub-node:
> > +- display-timings: Refer to binding doc display-timing.txt for
> > details.
> > +
> > +Examples:
> > +dcu: dcu at 2ce0000 {
> > + compatible = "fsl,ls1021a-dcu";
> > + reg = <0x0 0x2ce0000 0x0 0x10000>;
> > + clocks = <&platform_clk 0>;
> > + clock-names = "dcu";
> > + big-endian;
> > + display = <&display>;
> > +
> > + display: display at 0 {
> > + bits-per-pixel = <24>;
> > +
> > + display-timings {
> > + native-mode = <&timing0>;
> > + timing0: nl4827hc19 {
> > + clock-frequency = <10870000>;
> > + hactive = <480>;
> > + vactive = <272>;
> > + hback-porch = <2>;
> > + hfront-porch = <2>;
> > + vback-porch = <1>;
> > + vfront-porch = <1>;
> > + hsync-len = <41>;
> > + vsync-len = <2>;
> > + hsync-active = <1>;
> > + vsync-active = <1>;
> > + };
> > + };
> > + };
> > +};
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 885be14..a6cff2f4 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -3398,6 +3398,14 @@ S: Maintained
> > F: drivers/gpu/drm/imx/
> > F: Documentation/devicetree/bindings/drm/imx/
> >
> > +DRM DRIVERS FOR FREESCALE DCU
> > +M: Jianwei Wang <jianwei.wang at freescale.com>
> > +M: Alison Wang <alison.wang at freescale.com>
> > +L: dri-devel at lists.freedesktop.org
> > +S: Supported
> > +F: drivers/gpu/drm/fsl-dcu/
> > +F: Documentation/devicetree/bindings/drm/fsl-dcu/
> > +
> > DRM DRIVERS FOR NVIDIA TEGRA
> > M: Thierry Reding <thierry.reding at gmail.com>
> > M: Terje Bergström <tbergstrom at nvidia.com>
> > diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig index
> > 151a050..e64cf18 100644
> > --- a/drivers/gpu/drm/Kconfig
> > +++ b/drivers/gpu/drm/Kconfig
> > @@ -199,6 +199,8 @@ source "drivers/gpu/drm/bochs/Kconfig"
> >
> > source "drivers/gpu/drm/msm/Kconfig"
> >
> > +source "drivers/gpu/drm/fsl-dcu/Kconfig"
> > +
> > source "drivers/gpu/drm/tegra/Kconfig"
> >
> > source "drivers/gpu/drm/panel/Kconfig"
> > diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile index
> > 2c239b9..398eccf 100644
> > --- a/drivers/gpu/drm/Makefile
> > +++ b/drivers/gpu/drm/Makefile
> > @@ -56,6 +56,7 @@ obj-$(CONFIG_DRM_UDL) += udl/
> > obj-$(CONFIG_DRM_AST) += ast/
> > obj-$(CONFIG_DRM_ARMADA) += armada/
> > obj-$(CONFIG_DRM_ATMEL_HLCDC) += atmel-hlcdc/
> > +obj-$(CONFIG_DRM_FSL_DCU) += fsl-dcu/
> > obj-$(CONFIG_DRM_RCAR_DU) += rcar-du/
> > obj-$(CONFIG_DRM_SHMOBILE) +=shmobile/
> > obj-$(CONFIG_DRM_OMAP) += omapdrm/
> > diff --git a/drivers/gpu/drm/fsl-dcu/Kconfig b/drivers/gpu/drm/fsl-
> > dcu/Kconfig new file mode 100644 index 0000000..e4f8df0
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/Kconfig
> > @@ -0,0 +1,17 @@
> > +config DRM_FSL_DCU
> > + tristate "DRM Support for Freescale DCU"
> > + depends on DRM && OF && ARM
> > + select DRM_KMS_HELPER
> > + select DRM_KMS_CMA_HELPER
> > + select VIDEOMODE_HELPERS
> > + select BACKLIGHT_CLASS_DEVICE
> > + select BACKLIGHT_LCD_SUPPORT
> > + select REGMAP_MMIO
> > + select DRM_KMS_FB_HELPER
> > + select FB_SYS_FILLRECT
> > + select FB_SYS_COPYAREA
> > + select FB_SYS_IMAGEBLIT
> > + select FB_SYS_FOPS
> > + help
> > + Choose this option if you have an Freescale DCU chipset.
> > + If M is selected the module will be called fsl-dcu-drm.
> > diff --git a/drivers/gpu/drm/fsl-dcu/Makefile b/drivers/gpu/drm/fsl-
> > dcu/Makefile
> > new file mode 100644
> > index 0000000..336b4a6
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/Makefile
> > @@ -0,0 +1,7 @@
> > +fsl-dcu-drm-y := fsl_dcu_drm_drv.o \
> > + fsl_dcu_drm_kms.o \
> > + fsl_dcu_drm_connector.o \
> > + fsl_dcu_drm_plane.o \
> > + fsl_dcu_drm_crtc.o \
> > + fsl_dcu_drm_fbdev.o
> > +obj-$(CONFIG_DRM_FSL_DCU) += fsl-dcu-drm.o
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.c
> > new file mode 100644
> > index 0000000..799682d
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.c
> > @@ -0,0 +1,194 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <linux/backlight.h>
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_atomic_helper.h>
> > +#include <video/of_display_timing.h>
> > +
> > +#include "fsl_dcu_drm_drv.h"
> > +#include "fsl_dcu_drm_connector.h"
> > +
> > +static void fsl_dcu_drm_encoder_dpms(struct drm_encoder *encoder, int
> > +mode) { }
> > +
> > +static void fsl_dcu_drm_encoder_mode_prepare(struct drm_encoder
> > +*encoder) { }
> > +
> > +static void fsl_dcu_drm_encoder_mode_set(struct drm_encoder *encoder,
> > + struct drm_display_mode *mode,
> > + struct drm_display_mode *adjusted_mode) { }
> > +
> > +static void fsl_dcu_drm_encoder_mode_commit(struct drm_encoder
> > +*encoder) { }
> > +
> > +static void fsl_dcu_drm_encoder_disable(struct drm_encoder *encoder) {
> > +}
> > +
> > +static int
> > +fsl_dcu_drm_encoder_atomic_check(struct drm_encoder *encoder,
> > + struct drm_crtc_state *crtc_state,
> > + struct drm_connector_state *conn_state) {
> > + return 0;
> > +}
> > +
> > +static void fsl_dcu_drm_encoder_destroy(struct drm_encoder *encoder) {
> > + drm_encoder_cleanup(encoder);
> > +}
> > +
> > +static const struct drm_encoder_helper_funcs encoder_helper_funcs = {
> > + .dpms = fsl_dcu_drm_encoder_dpms,
> > + .prepare = fsl_dcu_drm_encoder_mode_prepare,
> > + .commit = fsl_dcu_drm_encoder_mode_commit,
> > + .mode_set = fsl_dcu_drm_encoder_mode_set,
> > + .disable = fsl_dcu_drm_encoder_disable,
> > + .atomic_check = fsl_dcu_drm_encoder_atomic_check, };
> > +
> > +static const struct drm_encoder_funcs encoder_funcs = {
> > + .destroy = fsl_dcu_drm_encoder_destroy, };
> > +
> > +int fsl_dcu_drm_encoder_create(struct fsl_dcu_drm_device *fsl_dev,
> > + struct drm_crtc *crtc)
> > +{
> > + struct drm_encoder *encoder = &fsl_dev->encoder;
> > + int ret;
> > +
> > + encoder->possible_crtcs = 1;
> > + ret = drm_encoder_init(fsl_dev->ddev, encoder, &encoder_funcs,
> > + DRM_MODE_ENCODER_LVDS);
> > + if (ret < 0)
> > + return ret;
> > +
> > + drm_encoder_helper_add(encoder, &encoder_helper_funcs);
> > + encoder->crtc = crtc;
> > +
> > + return 0;
> > +}
> > +
> > +#define to_fsl_dcu_connector(connector) \
> > + container_of(connector, struct fsl_dcu_drm_connector, connector)
> > +
> > +static int fsl_dcu_drm_connector_get_modes(struct drm_connector
> > +*connector) {
> > + struct drm_device *dev = connector->dev;
> > + struct device_node *display_np, *np = dev->dev->of_node;
> > + struct drm_display_mode *mode = drm_mode_create(connector->dev);
> > + int num_modes = 0;
> > +
> > + if (np) {
> > + display_np = of_parse_phandle(np, "display", 0);
> > + if (!display_np) {
> > + dev_err(dev->dev, "failed to find display phandle\n");
> > + return num_modes;
> > + }
> > + of_get_drm_display_mode(display_np, mode, OF_USE_NATIVE_MODE);
> > + mode->type |= DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
> > + drm_mode_probed_add(connector, mode);
> > + num_modes++;
> > + }
> > +
> > + return num_modes;
> > +}
> > +
> > +static int fsl_dcu_drm_connector_mode_valid(struct drm_connector
> > *connector,
> > + struct drm_display_mode *mode) {
> > + return MODE_OK;
> > +}
> > +
> > +static struct drm_encoder *
> > +fsl_dcu_drm_connector_best_encoder(struct drm_connector *connector) {
> > + struct fsl_dcu_drm_connector *fsl_con =
> > +to_fsl_dcu_connector(connector);
> > +
> > + return fsl_con->encoder;
> > +}
> > +
> > +static void fsl_dcu_drm_connector_destroy(struct drm_connector
> > +*connector) {
> > + drm_connector_unregister(connector);
> > + drm_connector_cleanup(connector);
> > +}
> > +
> > +static enum drm_connector_status
> > +fsl_dcu_drm_connector_detect(struct drm_connector *connector, bool
> > +force) {
> > + return connector_status_connected;
> > +}
> > +
> > +static const struct drm_connector_funcs fsl_dcu_drm_connector_funcs = {
> > + .dpms = drm_atomic_helper_connector_dpms,
> > + .reset = drm_atomic_helper_connector_reset,
> > + .detect = fsl_dcu_drm_connector_detect,
> > + .fill_modes = drm_helper_probe_single_connector_modes,
> > + .destroy = fsl_dcu_drm_connector_destroy,
> > + .atomic_duplicate_state =
> > drm_atomic_helper_connector_duplicate_state,
> > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> > +};
> > +
> > +static const struct drm_connector_helper_funcs connector_helper_funcs =
> {
> > + .get_modes = fsl_dcu_drm_connector_get_modes,
> > + .mode_valid = fsl_dcu_drm_connector_mode_valid,
> > + .best_encoder = fsl_dcu_drm_connector_best_encoder,
> > +};
> > +
> > +int fsl_dcu_drm_connector_create(struct fsl_dcu_drm_device *fsl_dev,
> > + struct drm_encoder *encoder)
> > +{
> > + struct drm_connector *connector = &fsl_dev->connector.connector;
> > + int ret;
> > +
> > + fsl_dev->connector.encoder = encoder;
> > +
> > + connector->display_info.width_mm = 0;
> > + connector->display_info.height_mm = 0;
> > +
> > + ret = drm_connector_init(fsl_dev->ddev, connector,
> > + &fsl_dcu_drm_connector_funcs,
> > + DRM_MODE_CONNECTOR_LVDS);
> > + if (ret < 0)
> > + return ret;
> > +
> > + connector->dpms = DRM_MODE_DPMS_OFF;
> > + drm_connector_helper_add(connector, &connector_helper_funcs);
> > + ret = drm_connector_register(connector);
> > + if (ret < 0)
> > + goto err_cleanup;
> > +
> > + ret = drm_mode_connector_attach_encoder(connector, encoder);
> > + if (ret < 0)
> > + goto err_sysfs;
> > +
> > + connector->encoder = encoder;
> > +
> > + drm_object_property_set_value
> > + (&connector->base, fsl_dev->ddev->mode_config.dpms_property,
> > + DRM_MODE_DPMS_OFF);
> > +
> > + return 0;
> > +
> > +err_sysfs:
> > + drm_connector_unregister(connector);
> > +err_cleanup:
> > + drm_connector_cleanup(connector);
> > + return ret;
> > +}
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.h
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.h
> > new file mode 100644
> > index 0000000..8141a29
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_connector.h
> > @@ -0,0 +1,30 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#ifndef __FSL_DCU_DRM_CONNECTOR_H__
> > +#define __FSL_DCU_DRM_CONNECTOR_H__
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_crtc.h>
> > +#include "fsl_dcu_drm_crtc.h"
> > +
> > +struct fsl_dcu_drm_device;
> > +struct fsl_dcu_drm_connector {
> > + struct drm_connector connector;
> > + struct drm_encoder *encoder;
> > +};
> > +
> > +int fsl_dcu_drm_encoder_create(struct fsl_dcu_drm_device *fsl_dev,
> > + struct drm_crtc *crtc);
> > +int fsl_dcu_drm_connector_create(struct fsl_dcu_drm_device *fsl_dev,
> > + struct drm_encoder *encoder);
> > +
> > +#endif /* __FSL_DCU_DRM_CONNECTOR_H__ */
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.c
> > new file mode 100644
> > index 0000000..4065a7c
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.c
> > @@ -0,0 +1,172 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <linux/regmap.h>
> > +#include <linux/clk.h>
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_atomic.h>
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_crtc.h>
> > +
> > +#include "fsl_dcu_drm_crtc.h"
> > +#include "fsl_dcu_drm_drv.h"
> > +#include "fsl_dcu_drm_plane.h"
> > +
> > +#define to_fsl_dcu_crtc(c) container_of(c, struct fsl_dcu_drm_crtc,
> > crtc)
> > +
> > +static void fsl_dcu_drm_crtc_mode_set_nofb(struct drm_crtc *crtc) {
> > + struct drm_device *dev = crtc->dev;
> > + struct fsl_dcu_drm_device *fsl_dev = dev->dev_private;
> > + struct drm_display_mode *mode = &crtc->state->mode;
> > + uint32_t hbp, hfp, hsw, vbp, vfp, vsw, div, index;
> > +
> > + DBG(": set mode: %d:\"%s\" %d %d %d %d %d %d %d %d %d %d 0x%x 0x%x",
> > + mode->base.id, mode->name,
> > + mode->vrefresh, mode->clock,
> > + mode->hdisplay, mode->hsync_start,
> > + mode->hsync_end, mode->htotal,
> > + mode->vdisplay, mode->vsync_start,
> > + mode->vsync_end, mode->vtotal,
> > + mode->type, mode->flags);
> > +
> > + index = drm_crtc_index(crtc);
> > + div = (uint32_t)clk_get_rate(fsl_dev->clk) / mode->clock / 1000;
> > +
> > + /* Configure timings: */
> > + hbp = mode->htotal - mode->hsync_end;
> > + hfp = mode->hsync_start - mode->hdisplay;
> > + hsw = mode->hsync_end - mode->hsync_start;
> > + vbp = mode->vtotal - mode->vsync_end;
> > + vfp = mode->vsync_start - mode->vdisplay;
> > + vsw = mode->vsync_end - mode->vsync_start;
> > +
> > + regmap_write(fsl_dev->regmap, DCU_HSYN_PARA,
> > + DCU_HSYN_PARA_BP(hbp) |
> > + DCU_HSYN_PARA_PW(hsw) |
> > + DCU_HSYN_PARA_FP(hfp));
> > + regmap_write(fsl_dev->regmap, DCU_VSYN_PARA,
> > + DCU_VSYN_PARA_BP(vbp) |
> > + DCU_VSYN_PARA_PW(vsw) |
> > + DCU_VSYN_PARA_FP(vfp));
> > + regmap_write(fsl_dev->regmap, DCU_DISP_SIZE,
> > + DCU_DISP_SIZE_DELTA_Y(mode->vdisplay) |
> > + DCU_DISP_SIZE_DELTA_X(mode->hdisplay));
> > + regmap_write(fsl_dev->regmap, DCU_DIV_RATIO, div);
> > + regmap_write(fsl_dev->regmap, DCU_UPDATE_MODE,
> > +DCU_UPDATE_MODE_READREG); }
> > +
> > +static bool fsl_dcu_drm_crtc_mode_fixup(struct drm_crtc *crtc,
> > + const struct drm_display_mode *mode,
> > + struct drm_display_mode *adjusted_mode) {
> > + return true;
> > +}
> > +
> > +static void fsl_dcu_drm_crtc_prepare(struct drm_crtc *crtc) { }
> > +
> > +/* Now enable the clocks, plane, pipe, and connectors that we set up.
> > +*/ static void fsl_dcu_drm_crtc_mode_commit(struct drm_crtc *crtc) { }
> > +
> > +static int fsl_dcu_drm_crtc_atomic_check(struct drm_crtc *crtc,
> > + struct drm_crtc_state *state)
> > +{
> > + return 0;
> > +}
> > +
> > +static void fsl_dcu_drm_crtc_atomic_begin(struct drm_crtc *crtc) { }
> > +
> > +static void fsl_dcu_drm_crtc_atomic_flush(struct drm_crtc *crtc) { }
> > +
> > +static void fsl_dcu_drm_disable_crtc(struct drm_crtc *crtc) { }
> > +
> > +static void fsl_dcu_drm_crtc_dpms(struct drm_crtc *crtc, int mode) { }
> > +
> > +static const struct drm_crtc_funcs fsl_dcu_drm_crtc_funcs = {
> > + .page_flip = drm_atomic_helper_page_flip,
> > + .set_config = drm_atomic_helper_set_config,
> > + .destroy = drm_crtc_cleanup,
> > + .reset = drm_atomic_helper_crtc_reset,
> > + .atomic_duplicate_state = drm_atomic_helper_crtc_duplicate_state,
> > + .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state,
> > +};
> > +
> > +static const struct drm_crtc_helper_funcs fsl_dcu_drm_crtc_helper_funcs
> =
> > {
> > + .disable = fsl_dcu_drm_disable_crtc,
> > + .mode_fixup = fsl_dcu_drm_crtc_mode_fixup,
> > + .mode_set = drm_helper_crtc_mode_set,
> > + .mode_set_nofb = fsl_dcu_drm_crtc_mode_set_nofb,
> > + .mode_set_base = drm_helper_crtc_mode_set_base,
> > + .prepare = fsl_dcu_drm_crtc_prepare,
> > + .commit = fsl_dcu_drm_crtc_mode_commit,
> > + .atomic_check = fsl_dcu_drm_crtc_atomic_check,
> > + .atomic_begin = fsl_dcu_drm_crtc_atomic_begin,
> > + .atomic_flush = fsl_dcu_drm_crtc_atomic_flush,
> > + .dpms = fsl_dcu_drm_crtc_dpms,
> > +};
> > +
> > +int fsl_dcu_drm_crtc_create(struct fsl_dcu_drm_device *fsl_dev) {
> > + struct drm_plane *primary;
> > + struct drm_crtc *crtc = &fsl_dev->crtc;
> > + int i, ret;
> > +
> > + primary = fsl_dcu_drm_primary_create_plane(fsl_dev->ddev);
> > + ret = drm_crtc_init_with_planes(fsl_dev->ddev, crtc, primary, NULL,
> > + &fsl_dcu_drm_crtc_funcs);
> > + if (ret < 0)
> > + return ret;
> > +
> > + drm_crtc_helper_add(crtc, &fsl_dcu_drm_crtc_helper_funcs);
> > +
> > + for (i = 0; i < DCU_TOTAL_LAYER_NUM; i++) {
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_1(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_2(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_3(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_4(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_5(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_6(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_7(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_8(i), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_9(i), 0);
> > + if (of_device_is_compatible(fsl_dev->np, "fsl,ls1021a-dcu"))
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_10(i), 0);
> > + }
> > + regmap_write(fsl_dev->regmap, DCU_SYN_POL,
> > + DCU_SYN_POL_INV_VS_LOW | DCU_SYN_POL_INV_HS_LOW);
> > + regmap_write(fsl_dev->regmap, DCU_BGND, DCU_BGND_R(0) |
> > + DCU_BGND_G(0) | DCU_BGND_B(0));
> > + regmap_write(fsl_dev->regmap, DCU_DCU_MODE,
> > + DCU_MODE_BLEND_ITER(1) | DCU_MODE_RASTER_EN);
> > + regmap_write(fsl_dev->regmap, DCU_THRESHOLD,
> > + DCU_THRESHOLD_LS_BF_VS(BF_VS_VAL) |
> > + DCU_THRESHOLD_OUT_BUF_HIGH(BUF_MAX_VAL) |
> > + DCU_THRESHOLD_OUT_BUF_LOW(BUF_MIN_VAL));
> > + regmap_update_bits(fsl_dev->regmap, DCU_DCU_MODE,
> > + DCU_MODE_DCU_MODE_MASK,
> > + DCU_MODE_DCU_MODE(DCU_MODE_OFF));
> > + regmap_write(fsl_dev->regmap, DCU_UPDATE_MODE,
> > +DCU_UPDATE_MODE_READREG);
> > +
> > + return 0;
> > +}
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.h
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.h
> > new file mode 100644
> > index 0000000..193785f
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_crtc.h
> > @@ -0,0 +1,22 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#ifndef __FSL_DCU_DRM_CRTC_H__
> > +#define __FSL_DCU_DRM_CRTC_H__
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_crtc.h>
> > +
> > +struct fsl_dcu_drm_device;
> > +
> > +int fsl_dcu_drm_crtc_create(struct fsl_dcu_drm_device *fsl_dev);
> > +
> > +#endif /* __FSL_DCU_DRM_CRTC_H__ */
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
> > new file mode 100644
> > index 0000000..1edf7be
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.c
> > @@ -0,0 +1,373 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/io.h>
> > +#include <linux/mm.h>
> > +#include <linux/module.h>
> > +#include <linux/of_platform.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/mfd/syscon.h>
> > +
> > +#include <drm/drmP.h>
> > +
> > +#include "fsl_dcu_drm_drv.h"
> > +#include "fsl_dcu_drm_crtc.h"
> > +#include "fsl_dcu_drm_kms.h"
> > +
> > +static int fsl_dcu_unload(struct drm_device *dev) {
> > + drm_mode_config_cleanup(dev);
> > + drm_vblank_cleanup(dev);
> > + drm_irq_uninstall(dev);
> > +
> > + dev->dev_private = NULL;
> > +
> > + return 0;
> > +}
> > +
> > +static struct regmap_config fsl_dcu_regmap_config = {
> > + .reg_bits = 32,
> > + .reg_stride = 4,
> > + .val_bits = 32,
> > +};
> > +
> > +static int fsl_dcu_bypass_tcon(struct fsl_dcu_drm_device *fsl_dev,
> > + struct device_node *np)
> > +{
> > + struct device_node *tcon_np;
> > + struct platform_device *pdev;
> > + struct clk *tcon_clk;
> > + struct resource *res;
> > + void __iomem *base;
> > +
> > + tcon_np = of_parse_phandle(np, "tcon-controller", 0);
> > + if (!tcon_np)
> > + return -EINVAL;
> > +
> > + pdev = of_find_device_by_node(tcon_np);
> > + if (!pdev)
> > + return -EINVAL;
> > +
> > + tcon_clk = devm_clk_get(&pdev->dev, "tcon");
> > + if (IS_ERR(tcon_clk))
> > + return PTR_ERR(tcon_clk);
> > + clk_prepare_enable(tcon_clk);
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res)
> > + return -ENODEV;
> > +
> > + base = devm_ioremap_resource(&pdev->dev, res);
> > + if (IS_ERR(base))
> > + return PTR_ERR(base);
> > +
> > + fsl_dev->tcon_regmap = devm_regmap_init_mmio(&pdev->dev,
> > + base, &fsl_dcu_regmap_config);
> > + if (IS_ERR(fsl_dev->tcon_regmap)) {
> > + dev_err(&pdev->dev, "regmap init failed\n");
> > + return PTR_ERR(fsl_dev->tcon_regmap);
> > + }
> > +
> > + regmap_write(fsl_dev->tcon_regmap, TCON_CTRL1, TCON_BYPASS_ENABLE);
> > + return 0;
> > +}
> > +
> > +static void dcu_pixclk_enable(void)
> > +{
> > + struct regmap *scfg_regmap;
> > +
> > + scfg_regmap = syscon_regmap_lookup_by_compatible("fsl,ls1021a-scfg");
> > + if (IS_ERR(scfg_regmap)) {
> > + pr_err("No syscfg phandle specified\n");
> > + return;
> > + }
> > +
> > + regmap_write(scfg_regmap, SCFG_PIXCLKCR, PXCK_ENABLE); }
> > +
> > +static int fsl_dcu_drm_irq_init(struct drm_device *dev) {
> > + struct platform_device *pdev = dev->platformdev;
> > + struct fsl_dcu_drm_device *fsl_dev = dev->dev_private;
> > + unsigned int int_mask;
> > + int ret;
> > +
> > + ret = drm_irq_install(dev, platform_get_irq(dev->platformdev, 0));
> > + if (ret < 0)
> > + dev_err(&pdev->dev, "failed to install IRQ handler\n");
> > +
> > + dev->irq_enabled = true;
> > + dev->vblank_disable_allowed = true;
> > +
> > + regmap_write(fsl_dev->regmap, DCU_INT_STATUS, 0);
> > + regmap_read(fsl_dev->regmap, DCU_INT_MASK, &int_mask);
> > + regmap_write(fsl_dev->regmap, DCU_INT_MASK, int_mask &
> > + ~DCU_INT_MASK_VBLANK);
> > + regmap_write(fsl_dev->regmap, DCU_UPDATE_MODE,
> > +DCU_UPDATE_MODE_READREG);
> > +
> > + return 0;
> > +}
> > +
> > +static int fsl_dcu_load(struct drm_device *dev, unsigned long flags) {
> > + struct platform_device *pdev = dev->platformdev;
> > + struct fsl_dcu_drm_device *fsl_dev;
> > + struct resource *res;
> > + void __iomem *base;
> > + int ret;
> > +
> > + fsl_dev = devm_kzalloc(&pdev->dev, sizeof(*fsl_dev), GFP_KERNEL);
> > + if (!fsl_dev)
> > + return -ENOMEM;
> > +
> > + fsl_dev->dev = &pdev->dev;
> > + fsl_dev->ddev = dev;
> > + fsl_dev->np = pdev->dev.of_node;
> > + dev->dev_private = fsl_dev;
> > + dev_set_drvdata(dev->dev, fsl_dev);
> > + drm_dev_set_unique(dev, dev_name(dev->dev));
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res) {
> > + dev_err(&pdev->dev, "could not get memory IO resource\n");
> > + return -ENODEV;
> > + }
> > +
> > + base = devm_ioremap_resource(&pdev->dev, res);
> > + if (IS_ERR(base)) {
> > + ret = PTR_ERR(base);
> > + return ret;
> > + }
> > +
> > + fsl_dev->clk = devm_clk_get(&pdev->dev, "dcu");
> > + if (IS_ERR(fsl_dev->clk)) {
> > + ret = PTR_ERR(fsl_dev->clk);
> > + dev_err(&pdev->dev, "could not get clock\n");
> > + return ret;
> > + }
> > + clk_prepare_enable(fsl_dev->clk);
> > + fsl_dev->regmap = devm_regmap_init_mmio(&pdev->dev, base,
> > + &fsl_dcu_regmap_config);
> > + if (IS_ERR(fsl_dev->regmap)) {
> > + dev_err(&pdev->dev, "regmap init failed\n");
> > + return PTR_ERR(fsl_dev->regmap);
> > + }
> > +
> > + /* Put TCON in bypass mode, so the input signals from DCU are passed
> > + * through TCON unchanged */
> > + fsl_dcu_bypass_tcon(fsl_dev, fsl_dev->np);
> > +
> > + if (of_device_is_compatible(fsl_dev->np, "fsl,ls1021a-dcu"))
> > + dcu_pixclk_enable();
> > + ret = fsl_dcu_drm_modeset_init(fsl_dev);
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "failed to initialize mode setting\n");
> > + return ret;
> > + }
> > +
> > + ret = drm_vblank_init(dev, dev->mode_config.num_crtc);
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "failed to initialize vblank\n");
> > + goto done;
> > + }
> > +
> > + ret = fsl_dcu_drm_irq_init(dev);
> > + if (ret < 0)
> > + goto done;
> > +
> > + fsl_dcu_fbdev_init(dev);
> > +
> > + return 0;
> > +done:
> > + if (ret)
> > + fsl_dcu_unload(dev);
> > +
> > + return ret;
> > +}
> > +
> > +static void fsl_dcu_drm_preclose(struct drm_device *dev, struct
> > +drm_file *file) { }
> > +
> > +static irqreturn_t fsl_dcu_drm_irq(int irq, void *arg) {
> > + struct drm_device *dev = arg;
> > + struct fsl_dcu_drm_device *fsl_dev = dev->dev_private;
> > + unsigned int int_status;
> > +
> > + regmap_read(fsl_dev->regmap, DCU_INT_STATUS, &int_status);
> > + if (int_status & DCU_INT_STATUS_VBLANK)
> > + drm_handle_vblank(dev, 0);
> > +
> > + regmap_write(fsl_dev->regmap, DCU_INT_STATUS, 0xffffffff);
> > + regmap_write(fsl_dev->regmap, DCU_UPDATE_MODE,
> > +DCU_UPDATE_MODE_READREG);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int fsl_dcu_drm_enable_vblank(struct drm_device *dev, int crtc)
> > +{
> > + return 0;
> > +}
> > +
> > +static void fsl_dcu_drm_disable_vblank(struct drm_device *dev, int
> > +crtc) { }
> > +
> > +static const struct file_operations fsl_dcu_drm_fops = {
> > + .owner = THIS_MODULE,
> > + .open = drm_open,
> > + .release = drm_release,
> > + .unlocked_ioctl = drm_ioctl,
> > +#ifdef CONFIG_COMPAT
> > + .compat_ioctl = drm_compat_ioctl,
> > +#endif
> > + .poll = drm_poll,
> > + .read = drm_read,
> > + .llseek = no_llseek,
> > + .mmap = drm_gem_cma_mmap,
> > +};
> > +
> > +static struct drm_driver fsl_dcu_drm_driver = {
> > + .driver_features = DRIVER_HAVE_IRQ | DRIVER_GEM | DRIVER_MODESET
> > + | DRIVER_PRIME,
> > + .load = fsl_dcu_load,
> > + .unload = fsl_dcu_unload,
> > + .preclose = fsl_dcu_drm_preclose,
> > + .irq_handler = fsl_dcu_drm_irq,
> > + .get_vblank_counter = drm_vblank_count,
> > + .enable_vblank = fsl_dcu_drm_enable_vblank,
> > + .disable_vblank = fsl_dcu_drm_disable_vblank,
> > + .gem_free_object = drm_gem_cma_free_object,
> > + .gem_vm_ops = &drm_gem_cma_vm_ops,
> > + .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
> > + .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
> > + .gem_prime_import = drm_gem_prime_import,
> > + .gem_prime_export = drm_gem_prime_export,
> > + .gem_prime_get_sg_table = drm_gem_cma_prime_get_sg_table,
> > + .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
> > + .gem_prime_vmap = drm_gem_cma_prime_vmap,
> > + .gem_prime_vunmap = drm_gem_cma_prime_vunmap,
> > + .gem_prime_mmap = drm_gem_cma_prime_mmap,
> > + .dumb_create = drm_gem_cma_dumb_create,
> > + .dumb_map_offset = drm_gem_cma_dumb_map_offset,
> > + .dumb_destroy = drm_gem_dumb_destroy,
> > + .fops = &fsl_dcu_drm_fops,
> > + .name = "fsl-dcu-drm",
> > + .desc = "Freescale DCU DRM",
> > + .date = "20150213",
> > + .major = 1,
> > + .minor = 0,
> > +};
> > +
> > +#ifdef CONFIG_PM_SLEEP
> > +static void dcu_pixclk_disable(void)
> > +{
> > + struct regmap *scfg_regmap;
> > +
> > + scfg_regmap = syscon_regmap_lookup_by_compatible("fsl,ls1021a-scfg");
> > + if (IS_ERR(scfg_regmap)) {
> > + pr_err("No syscfg phandle specified\n");
> > + return;
> > + }
> > +
> > + regmap_write(scfg_regmap, SCFG_PIXCLKCR, PXCK_DISABLE); }
> > +
> > +static int fsl_dcu_drm_pm_suspend(struct device *dev) {
> > + struct fsl_dcu_drm_device *fsl_dev = dev_get_drvdata(dev);
> > +
> > + if (of_device_is_compatible(fsl_dev->np, "fsl,ls1021a-dcu"))
> > + dcu_pixclk_disable();
> > +
> > + drm_kms_helper_poll_disable(fsl_dev->ddev);
> > + regcache_cache_only(fsl_dev->regmap, true);
> > + regcache_mark_dirty(fsl_dev->regmap);
> > + clk_disable_unprepare(fsl_dev->clk);
> > +
> > + if (fsl_dev->tcon_regmap) {
> > + regcache_cache_only(fsl_dev->tcon_regmap, true);
> > + regcache_mark_dirty(fsl_dev->tcon_regmap);
> > + clk_disable_unprepare(fsl_dev->tcon_clk);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int fsl_dcu_drm_pm_resume(struct device *dev) {
> > + struct fsl_dcu_drm_device *fsl_dev = dev_get_drvdata(dev);
> > +
> > + /* Enable clocks and restore all registers */
> > + if (fsl_dev->tcon_regmap) {
> > + clk_prepare_enable(fsl_dev->tcon_clk);
> > + regcache_cache_only(fsl_dev->tcon_regmap, false);
> > + regcache_sync(fsl_dev->tcon_regmap);
> > + }
> > +
> > + clk_prepare_enable(fsl_dev->clk);
> > + drm_kms_helper_poll_enable(fsl_dev->ddev);
> > + regcache_cache_only(fsl_dev->regmap, false);
> > + regcache_sync(fsl_dev->regmap);
> > +
> > + if (of_device_is_compatible(fsl_dev->np, "fsl,ls1021a-dcu"))
> > + dcu_pixclk_enable();
> > +
> > + return 0;
> > +}
> > +#endif
> > +
> > +static const struct dev_pm_ops fsl_dcu_drm_pm_ops = {
> > + SET_SYSTEM_SLEEP_PM_OPS(fsl_dcu_drm_pm_suspend,
> > fsl_dcu_drm_pm_resume)
> > +};
> > +
> > +static int fsl_dcu_drm_probe(struct platform_device *pdev) {
> > + return drm_platform_init(&fsl_dcu_drm_driver, pdev); }
> > +
> > +static int fsl_dcu_drm_remove(struct platform_device *pdev) {
> > + struct fsl_dcu_drm_device *fsl_dev = platform_get_drvdata(pdev);
> > +
> > + drm_put_dev(fsl_dev->ddev);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id fsl_dcu_of_match[] = {
> > + { .compatible = "fsl,ls1021a-dcu", },
> > + { .compatible = "fsl,vf610-dcu", },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, fsl_dcu_of_match);
> > +
> > +static struct platform_driver fsl_dcu_drm_platform_driver = {
> > + .probe = fsl_dcu_drm_probe,
> > + .remove = fsl_dcu_drm_remove,
> > + .driver = {
> > + .owner = THIS_MODULE,
> > + .name = "fsl,dcu",
> > + .pm = &fsl_dcu_drm_pm_ops,
> > + .of_match_table = fsl_dcu_of_match,
> > + },
> > +};
> > +
> > +module_platform_driver(fsl_dcu_drm_platform_driver);
> > +
> > +MODULE_ALIAS("platform:fsl-dcu-drm");
> > +MODULE_DESCRIPTION("Freescale DCU DRM Driver"); MODULE_LICENSE("GPL");
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
> > new file mode 100644
> > index 0000000..40df1c5
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_drv.h
> > @@ -0,0 +1,223 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#ifndef __FSL_DCU_DRM_DRV_H__
> > +#define __FSL_DCU_DRM_DRV_H__
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/spinlock.h>
> > +#include <stddef.h>
> > +#include <drm/drm.h>
> > +#include <drm/drmP.h>
> > +#include <drm/drm_fb_helper.h>
> > +#include <drm/drm_crtc_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <drm/drm_fb_cma_helper.h>
> > +
> > +#include "fsl_dcu_drm_crtc.h"
> > +#include "fsl_dcu_drm_plane.h"
> > +#include "fsl_dcu_drm_connector.h"
> > +#define DRIVER_NAME "fsl-dcu-drm"
> > +
> > +#define DCU_DCU_MODE 0x0010
> > +#define DCU_MODE_BLEND_ITER(x) ((x) << 20)
> > +#define DCU_MODE_RASTER_EN BIT(14)
> > +#define DCU_MODE_DCU_MODE(x) (x)
> > +#define DCU_MODE_DCU_MODE_MASK 0x03
> > +#define DCU_MODE_OFF 0
> > +#define DCU_MODE_NORMAL 1
> > +#define DCU_MODE_TEST 2
> > +#define DCU_MODE_COLORBAR 3
> > +
> > +#define DCU_BGND 0x0014
> > +#define DCU_BGND_R(x) ((x) << 16)
> > +#define DCU_BGND_G(x) ((x) << 8)
> > +#define DCU_BGND_B(x) (x)
> > +
> > +#define DCU_DISP_SIZE 0x0018
> > +#define DCU_DISP_SIZE_DELTA_Y(x) ((x) << 16)
> > +/*Regisiter value 1/16 of horizontal resolution*/
> > +#define DCU_DISP_SIZE_DELTA_X(x) ((x) >> 4)
> > +
> > +#define DCU_HSYN_PARA 0x001c
> > +#define DCU_HSYN_PARA_BP(x) ((x) << 22)
> > +#define DCU_HSYN_PARA_PW(x) ((x) << 11)
> > +#define DCU_HSYN_PARA_FP(x) (x)
> > +
> > +#define DCU_VSYN_PARA 0x0020
> > +#define DCU_VSYN_PARA_BP(x) ((x) << 22)
> > +#define DCU_VSYN_PARA_PW(x) ((x) << 11)
> > +#define DCU_VSYN_PARA_FP(x) (x)
> > +
> > +#define DCU_SYN_POL 0x0024
> > +#define DCU_SYN_POL_INV_PXCK_FALL (0 << 6)
> > +#define DCU_SYN_POL_NEG_REMAIN (0 << 5)
> > +#define DCU_SYN_POL_INV_VS_LOW BIT(1)
> > +#define DCU_SYN_POL_INV_HS_LOW BIT(0)
> > +
> > +#define DCU_THRESHOLD 0x0028
> > +#define DCU_THRESHOLD_LS_BF_VS(x) ((x) << 16)
> > +#define DCU_THRESHOLD_OUT_BUF_HIGH(x) ((x) << 8)
> > +#define DCU_THRESHOLD_OUT_BUF_LOW(x) (x)
> > +#define BF_VS_VAL 0x03
> > +#define BUF_MAX_VAL 0x78
> > +#define BUF_MIN_VAL 0x0a
> > +
> > +#define DCU_INT_STATUS 0x002C
> > +#define DCU_INT_STATUS_VSYNC BIT(0)
> > +#define DCU_INT_STATUS_UNDRUN BIT(1)
> > +#define DCU_INT_STATUS_LSBFVS BIT(2)
> > +#define DCU_INT_STATUS_VBLANK BIT(3)
> > +#define DCU_INT_STATUS_CRCREADY BIT(4)
> > +#define DCU_INT_STATUS_CRCOVERFLOW BIT(5)
> > +#define DCU_INT_STATUS_P1FIFOLO BIT(6)
> > +#define DCU_INT_STATUS_P1FIFOHI BIT(7)
> > +#define DCU_INT_STATUS_P2FIFOLO BIT(8)
> > +#define DCU_INT_STATUS_P2FIFOHI BIT(9)
> > +#define DCU_INT_STATUS_PROGEND BIT(10)
> > +#define DCU_INT_STATUS_IPMERROR BIT(11)
> > +#define DCU_INT_STATUS_LYRTRANS BIT(12)
> > +#define DCU_INT_STATUS_DMATRANS BIT(14)
> > +#define DCU_INT_STATUS_P3FIFOLO BIT(16)
> > +#define DCU_INT_STATUS_P3FIFOHI BIT(17)
> > +#define DCU_INT_STATUS_P4FIFOLO BIT(18)
> > +#define DCU_INT_STATUS_P4FIFOHI BIT(19)
> > +#define DCU_INT_STATUS_P1EMPTY BIT(26)
> > +#define DCU_INT_STATUS_P2EMPTY BIT(27)
> > +#define DCU_INT_STATUS_P3EMPTY BIT(28)
> > +#define DCU_INT_STATUS_P4EMPTY BIT(29)
> > +
> > +#define DCU_INT_MASK 0x0030
> > +#define DCU_INT_MASK_VSYNC BIT(0)
> > +#define DCU_INT_MASK_UNDRUN BIT(1)
> > +#define DCU_INT_MASK_LSBFVS BIT(2)
> > +#define DCU_INT_MASK_VBLANK BIT(3)
> > +#define DCU_INT_MASK_CRCREADY BIT(4)
> > +#define DCU_INT_MASK_CRCOVERFLOW BIT(5)
> > +#define DCU_INT_MASK_P1FIFOLO BIT(6)
> > +#define DCU_INT_MASK_P1FIFOHI BIT(7)
> > +#define DCU_INT_MASK_P2FIFOLO BIT(8)
> > +#define DCU_INT_MASK_P2FIFOHI BIT(9)
> > +#define DCU_INT_MASK_PROGEND BIT(10)
> > +#define DCU_INT_MASK_IPMERROR BIT(11)
> > +#define DCU_INT_MASK_LYRTRANS BIT(12)
> > +#define DCU_INT_MASK_DMATRANS BIT(14)
> > +#define DCU_INT_MASK_P3FIFOLO BIT(16)
> > +#define DCU_INT_MASK_P3FIFOHI BIT(17)
> > +#define DCU_INT_MASK_P4FIFOLO BIT(18)
> > +#define DCU_INT_MASK_P4FIFOHI BIT(19)
> > +#define DCU_INT_MASK_P1EMPTY BIT(26)
> > +#define DCU_INT_MASK_P2EMPTY BIT(27)
> > +#define DCU_INT_MASK_P3EMPTY BIT(28)
> > +#define DCU_INT_MASK_P4EMPTY BIT(29)
> > +
> > +#define DCU_DIV_RATIO 0x0054
> > +
> > +#define DCU_UPDATE_MODE 0x00cc
> > +#define DCU_UPDATE_MODE_MODE BIT(31)
> > +#define DCU_UPDATE_MODE_READREG BIT(30)
> > +
> > +#define DCU_DCFB_MAX 0x300
> > +
> > +#define DCU_CTRLDESCLN_1(x) (0x200 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_1_HEIGHT(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_1_WIDTH(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_2(x) (0x204 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_2_POSY(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_2_POSX(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_3(x) (0x208 + (x) * 0x40)
> > +
> > +#define DCU_CTRLDESCLN_4(x) (0x20c + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_4_EN BIT(31)
> > +#define DCU_CTRLDESCLN_4_TILE_EN BIT(30)
> > +#define DCU_CTRLDESCLN_4_DATA_SEL_CLUT BIT(29)
> > +#define DCU_CTRLDESCLN_4_SAFETY_EN BIT(28)
> > +#define DCU_CTRLDESCLN_4_TRANS(x) ((x) << 20)
> > +#define DCU_CTRLDESCLN_4_BPP(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_4_RLE_EN BIT(15)
> > +#define DCU_CTRLDESCLN_4_LUOFFS(x) ((x) << 4)
> > +#define DCU_CTRLDESCLN_4_BB_ON BIT(2)
> > +#define DCU_CTRLDESCLN_4_AB(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_5(x) (0x210 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_5_CKMAX_R(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_5_CKMAX_G(x) ((x) << 8)
> > +#define DCU_CTRLDESCLN_5_CKMAX_B(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_6(x) (0x214 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_6_CKMIN_R(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_6_CKMIN_G(x) ((x) << 8)
> > +#define DCU_CTRLDESCLN_6_CKMIN_B(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_7(x) (0x218 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_7_TILE_VER(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_7_TILE_HOR(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_8(x) (0x21c + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_8_FG_FCOLOR(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_9(x) (0x220 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_9_BG_BCOLOR(x) (x)
> > +
> > +#define DCU_CTRLDESCLN_10(x) (0x224 + (x) * 0x40)
> > +#define DCU_CTRLDESCLN_10_POST_SKIP(x) ((x) << 16)
> > +#define DCU_CTRLDESCLN_10_PRE_SKIP(x) (x)
> > +
> > +#ifdef CONFIG_SOC_VF610
> > +#define DCU_TOTAL_LAYER_NUM 64
> > +#define DCU_LAYER_NUM_MAX 6
> > +#else
> > +#define DCU_TOTAL_LAYER_NUM 16
> > +#define DCU_LAYER_NUM_MAX 4
> > +#endif
> > +
> > +#define FSL_DCU_RGB565 4
> > +#define FSL_DCU_RGB888 5
> > +#define FSL_DCU_ARGB8888 6
> > +#define FSL_DCU_ARGB1555 11
> > +#define FSL_DCU_ARGB4444 12
> > +#define FSL_DCU_YUV422 14
> > +
> > +#define TCON_CTRL1 0x0000
> > +#define TCON_BYPASS_ENABLE BIT(29)
> > +
> > +#define SCFG_PIXCLKCR 0x28
> > +#define PXCK_ENABLE BIT(31)
> > +#define PXCK_DISABLE 0
> > +
> > +#define DBG(fmt, ...) DRM_DEBUG(fmt"\n", ##__VA_ARGS__)
> > +
> > +struct clk;
> > +struct device;
> > +struct drm_device;
> > +
> > +struct fsl_dcu_drm_device {
> > + struct device *dev;
> > + struct device_node *np;
> > + struct regmap *regmap;
> > + struct regmap *tcon_regmap;
> > + unsigned int irq;
> > + struct clk *clk;
> > + struct clk *tcon_clk;
> > + /*protects hardware register*/
> > + spinlock_t irq_lock;
> > + struct drm_device *ddev;
> > + struct drm_fbdev_cma *fbdev;
> > + struct drm_crtc crtc;
> > + struct drm_encoder encoder;
> > + struct fsl_dcu_drm_connector connector; };
> > +
> > +void fsl_dcu_fbdev_init(struct drm_device *dev);
> > +
> > +#endif /* __FSL_DCU_DRM_DRV_H__ */
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_fbdev.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_fbdev.c
> > new file mode 100644
> > index 0000000..f8ef0e1
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_fbdev.c
> > @@ -0,0 +1,26 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > +it
> > + * under the terms of the GNU General Public License version 2 as
> > +published by
> > + * the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> > +WITHOUT
> > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
> > +or
> > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
> > +License for
> > + * more details.
> > + *
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_fb_cma_helper.h>
> > +
> > +#include "fsl_dcu_drm_drv.h"
> > +
> > +/* initialize fbdev helper */
> > +void fsl_dcu_fbdev_init(struct drm_device *dev) {
> > + struct fsl_dcu_drm_device *fsl_dev = dev_get_drvdata(dev->dev);
> > +
> > + fsl_dev->fbdev = drm_fbdev_cma_init(dev, 24, 1, 1); }
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.c
> > new file mode 100644
> > index 0000000..0de21c6
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.c
> > @@ -0,0 +1,42 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_atomic_helper.h>
> > +
> > +#include "fsl_dcu_drm_crtc.h"
> > +#include "fsl_dcu_drm_connector.h"
> > +#include "fsl_dcu_drm_drv.h"
> > +
> > +static const struct drm_mode_config_funcs fsl_dcu_drm_mode_config_funcs
> =
> > {
> > + .fb_create = drm_fb_cma_create,
> > + .atomic_check = drm_atomic_helper_check,
> > + .atomic_commit = drm_atomic_helper_commit, };
> > +
> > +int fsl_dcu_drm_modeset_init(struct fsl_dcu_drm_device *fsl_dev) {
> > + drm_mode_config_init(fsl_dev->ddev);
> > +
> > + fsl_dev->ddev->mode_config.min_width = 0;
> > + fsl_dev->ddev->mode_config.min_height = 0;
> > + fsl_dev->ddev->mode_config.max_width = 2031;
> > + fsl_dev->ddev->mode_config.max_height = 2047;
> > + fsl_dev->ddev->mode_config.funcs = &fsl_dcu_drm_mode_config_funcs;
> > +
> > + drm_kms_helper_poll_init(fsl_dev->ddev);
> > + fsl_dcu_drm_crtc_create(fsl_dev);
> > + fsl_dcu_drm_encoder_create(fsl_dev, &fsl_dev->crtc);
> > + fsl_dcu_drm_connector_create(fsl_dev, &fsl_dev->encoder);
> > + drm_mode_config_reset(fsl_dev->ddev);
> > +
> > + return 0;
> > +}
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.h
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.h
> > new file mode 100644
> > index 0000000..b9bd299
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_kms.h
> > @@ -0,0 +1,17 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#ifndef __FSL_DCU_DRM_KMS_H__
> > +#define __FSL_DCU_DRM_KMS_H__
> > +
> > +int fsl_dcu_drm_modeset_init(struct fsl_dcu_drm_device *fsl_dev);
> > +
> > +#endif /* __FSL_DCU_DRM_KMS_H__ */
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.c
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.c
> > new file mode 100644
> > index 0000000..6146e80
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.c
> > @@ -0,0 +1,192 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#include <drm/drmP.h>
> > +#include <drm/drm_crtc.h>
> > +#include <drm/drm_crtc_helper.h>
> > +#include <drm/drm_fb_cma_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <linux/regmap.h>
> > +#include <drm/drm_plane_helper.h>
> > +#include <drm/drm_atomic_helper.h>
> > +
> > +#include "fsl_dcu_drm_drv.h"
> > +#include "fsl_dcu_drm_kms.h"
> > +#include "fsl_dcu_drm_plane.h"
> > +
> > +#define to_fsl_dcu_plane(plane) \
> > + container_of(plane, struct fsl_dcu_drm_plane, plane)
> > +
> > +static int
> > +fsl_dcu_drm_plane_prepare_fb(struct drm_plane *plane,
> > + struct drm_framebuffer *fb,
> > + const struct drm_plane_state *new_state) {
> > + return 0;
> > +}
> > +
> > +static void
> > +fsl_dcu_drm_plane_cleanup_fb(struct drm_plane *plane,
> > + struct drm_framebuffer *fb,
> > + const struct drm_plane_state *new_state) { }
> > +
> > +static int fsl_dcu_drm_plane_atomic_check(struct drm_plane *plane,
> > + struct drm_plane_state *state)
> > +{
> > + return 0;
> > +}
> > +
> > +static void fsl_dcu_drm_plane_atomic_disable(struct drm_plane *plane,
> > + struct drm_plane_state *old_state) { }
> > +
> > +void fsl_dcu_drm_plane_atomic_update(struct drm_plane *plane,
> > + struct drm_plane_state *old_state) {
> > + struct fsl_dcu_drm_device *fsl_dev = plane->dev->dev_private;
> > + struct drm_plane_state *state = plane->state;
> > + struct drm_framebuffer *fb = plane->state->fb;
> > + u32 index, alpha, bpp;
> > + struct drm_gem_cma_object *gem;
> > + struct fsl_dcu_drm_plane *fsl_plane = to_fsl_dcu_plane(plane);
> > +
> > + index = fsl_plane->index;
> > + gem = drm_fb_cma_get_gem_obj(fb, 0);
> > +
> > + switch (fb->pixel_format) {
> > + case DRM_FORMAT_RGB565:
> > + bpp = FSL_DCU_RGB565;
> > + alpha = 0xff;
> > + break;
> > + case DRM_FORMAT_RGB888:
> > + bpp = FSL_DCU_RGB888;
> > + alpha = 0xff;
> > + break;
> > + case DRM_FORMAT_ARGB8888:
> > + bpp = FSL_DCU_ARGB8888;
> > + alpha = 0xff;
> > + break;
> > + case DRM_FORMAT_BGRA4444:
> > + bpp = FSL_DCU_ARGB4444;
> > + alpha = 0xff;
> > + break;
> > + case DRM_FORMAT_ARGB1555:
> > + bpp = FSL_DCU_ARGB1555;
> > + alpha = 0xff;
> > + break;
> > + case DRM_FORMAT_YUV422:
> > + bpp = FSL_DCU_YUV422;
> > + alpha = 0xff;
> > + break;
> > + default:
> > + return;
> > + }
> > +
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_1(index),
> > + DCU_CTRLDESCLN_1_HEIGHT(state->crtc_h) |
> > + DCU_CTRLDESCLN_1_WIDTH(state->crtc_w));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_2(index),
> > + DCU_CTRLDESCLN_2_POSY(state->crtc_y) |
> > + DCU_CTRLDESCLN_2_POSX(state->crtc_x));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_3(index), gem->paddr);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_4(index),
> > + DCU_CTRLDESCLN_4_EN |
> > + DCU_CTRLDESCLN_4_TRANS(alpha) |
> > + DCU_CTRLDESCLN_4_BPP(bpp) |
> > + DCU_CTRLDESCLN_4_AB(0));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_5(index),
> > + DCU_CTRLDESCLN_5_CKMAX_R(0xFF) |
> > + DCU_CTRLDESCLN_5_CKMAX_G(0xFF) |
> > + DCU_CTRLDESCLN_5_CKMAX_B(0xFF));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_6(index),
> > + DCU_CTRLDESCLN_6_CKMIN_R(0) |
> > + DCU_CTRLDESCLN_6_CKMIN_G(0) |
> > + DCU_CTRLDESCLN_6_CKMIN_B(0));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_7(index), 0);
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_8(index),
> > + DCU_CTRLDESCLN_8_FG_FCOLOR(0));
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_9(index),
> > + DCU_CTRLDESCLN_9_BG_BCOLOR(0));
> > + if (of_device_is_compatible(fsl_dev->np, "fsl,ls1021a-dcu"))
> > + regmap_write(fsl_dev->regmap, DCU_CTRLDESCLN_10(index),
> > + DCU_CTRLDESCLN_10_POST_SKIP(0) |
> > + DCU_CTRLDESCLN_10_PRE_SKIP(0));
> > + regmap_update_bits(fsl_dev->regmap, DCU_DCU_MODE,
> > + DCU_MODE_DCU_MODE_MASK,
> > + DCU_MODE_DCU_MODE(DCU_MODE_NORMAL));
> > + regmap_write(fsl_dev->regmap, DCU_UPDATE_MODE,
> > +DCU_UPDATE_MODE_READREG); }
> > +
> > +int fsl_dcu_drm_plane_disable(struct drm_plane *plane) {
> > + return 0;
> > +}
> > +
> > +void fsl_dcu_drm_plane_destroy(struct drm_plane *plane) {
> > + fsl_dcu_drm_plane_disable(plane);
> > + drm_plane_cleanup(plane);
> > +}
> > +
> > +static const uint32_t fsl_dcu_drm_plane_formats[] = {
> > + DRM_FORMAT_RGB565,
> > + DRM_FORMAT_RGB888,
> > + DRM_FORMAT_ARGB8888,
> > + DRM_FORMAT_ARGB4444,
> > + DRM_FORMAT_ARGB1555,
> > + DRM_FORMAT_YUV422,
> > +};
> > +
> > +static const struct drm_plane_funcs fsl_dcu_drm_plane_funcs = {
> > + .update_plane = drm_atomic_helper_update_plane,
> > + .disable_plane = drm_atomic_helper_disable_plane,
> > + .destroy = fsl_dcu_drm_plane_destroy,
> > + .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
> > + .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
> > + .reset = drm_atomic_helper_plane_reset, };
> > +
> > +static const struct drm_plane_helper_funcs
> fsl_dcu_drm_plane_helper_funcs
> > = {
> > + .prepare_fb = fsl_dcu_drm_plane_prepare_fb,
> > + .cleanup_fb = fsl_dcu_drm_plane_cleanup_fb,
> > + .atomic_check = fsl_dcu_drm_plane_atomic_check,
> > + .atomic_update = fsl_dcu_drm_plane_atomic_update,
> > + .atomic_disable = fsl_dcu_drm_plane_atomic_disable, };
> > +
> > +struct drm_plane *fsl_dcu_drm_primary_create_plane(struct drm_device
> > +*dev) {
> > + struct drm_plane *primary;
> > + int ret;
> > +
> > + primary = kzalloc(sizeof(*primary), GFP_KERNEL);
> > + if (!primary) {
> > + DRM_DEBUG_KMS("Failed to allocate primary plane\n");
> > + return NULL;
> > + }
> > +
> > + /* possible_crtc's will be filled in later by crtc_init */
> > + ret = drm_universal_plane_init(dev, primary, 0,
> > + &fsl_dcu_drm_plane_funcs,
> > + fsl_dcu_drm_plane_formats,
> > + ARRAY_SIZE(fsl_dcu_drm_plane_formats),
> > + DRM_PLANE_TYPE_PRIMARY);
> > + if (ret) {
> > + kfree(primary);
> > + primary = NULL;
> > + }
> > + drm_plane_helper_add(primary, &fsl_dcu_drm_plane_helper_funcs);
> > +
> > + return primary;
> > +}
> > diff --git a/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.h
> > b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.h
> > new file mode 100644
> > index 0000000..ccbfa61
> > --- /dev/null
> > +++ b/drivers/gpu/drm/fsl-dcu/fsl_dcu_drm_plane.h
> > @@ -0,0 +1,23 @@
> > +/*
> > + * Copyright 2015 Freescale Semiconductor, Inc.
> > + *
> > + * Freescale DCU drm device driver
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License as published by
> > + * the Free Software Foundation; either version 2 of the License, or
> > + * (at your option) any later version.
> > + */
> > +
> > +#ifndef __FSL_DCU_DRM_PLANE_H__
> > +#define __FSL_DCU_DRM_PLANE_H__
> > +
> > +struct fsl_dcu_drm_device;
> > +struct fsl_dcu_drm_plane {
> > + struct drm_plane plane;
> > + unsigned int index;
> > +};
> > +
> > +struct drm_plane *fsl_dcu_drm_primary_create_plane(struct drm_device
> > +*dev);
> > +
> > +#endif /* __FSL_DCU_DRM_PLANE_H__ */
> > --
> > 2.1.0.27.g96db324
More information about the linux-arm-kernel
mailing list