[PATCH v2] arm, imx6, dts: add DT for aristainetos2 board
Shawn Guo
shawnguo at kernel.org
Mon May 18 04:31:35 PDT 2015
On Mon, May 11, 2015 at 11:02:54AM +0200, Heiko Schocher wrote:
> This patch add support for the imx6dl based aristainetos2 board
What are the differences between aristainetos2 and aristainetos board?
> with following configuration:
>
> CPU: Freescale i.MX6DL rev1.1 at 792 MHz
> MReset cause: POR
> MBoard: aristaitenos2
> DRAM: 1 GiB
> NAND: 1024 MiB
> MMC: FSL_SDHC: 0, FSL_SDHC: 1
> SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
> Display: lb07wv8 (800x480)
>
> As this board can used with 2 different display types, the
> differences between them are extracted into 2 DTS files, and
> the common settings are collected in a common file.
>
> Signed-off-by: Heiko Schocher <hs at denx.de>
> ---
>
> Changes in v2:
> - add comments from Sascha Hauer:
> - remove "clock-frequency" property in i2c nodes
> - correct indentation in some pinctrl nodes
> - move pin settings out of "gpiogrp" where it was possible
> led pins not moved, as they used through sysfs
>
> arch/arm/boot/dts/imx6dl-aristainetos2_4.dts | 124 ++++++
> arch/arm/boot/dts/imx6dl-aristainetos2_7.dts | 63 +++
> arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi | 627 +++++++++++++++++++++++++++
> 3 files changed, 814 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
Add them as DTB target into arch/arm/boot/dts/Makefile.
> create mode 100644 arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
>
> diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
> new file mode 100644
> index 0000000..43916a0
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
> @@ -0,0 +1,124 @@
> +/*
> + * support fot the imx6 based aristainetos2 board
> + *
> + * Copyright (C) 2015 Heiko Schocher <hs at denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
GPL/X11 dual licence is suggested for new DTS files. See
arch/arm/boot/dts/imx6sl-warp.dts for an example.
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-aristainetos2.dtsi"
> +
> +/ {
> + model = "aristainetos2 i.MX6 Dual Lite Board 4";
> + compatible = "fsl,imx6dl";
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 5000000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <7>;
> + status = "okay";
status = "okay" is mostly used in board level dts to enable device that
is by default disabled in <soc>.dtsi. In your case here, it can just be
saved.
> + };
> +
> + memory {
> + reg = <0x10000000 0x40000000>;
> + };
> +
> + soc {
> + display0: display at di0 {
> + compatible = "fsl,imx-parallel-display";
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_1_80Ohm_clk>;
> + fsl,panel = <&lcd_panel>;
What is this? I failed to find it in Documentation/devicetree/bindings/
> + status = "okay";
Can be saved?
> +
> + port {
> + display0_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> + };
> + };
> +};
> +
> +&ecspi1 {
> + lcd_panel: display at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "lg,lg4573";
> + spi-max-frequency = <10000000>;
> + reg = <0>;
> + power-on-delay = <10>;
> + display-timings {
> + 480x800p57 {
> + native-mode;
> + clock-frequency = <27000027>;
> + hactive = <480>;
> + vactive = <800>;
> + hfront-porch = <10>;
> + hback-porch = <59>;
> + hsync-len = <10>;
> + vback-porch = <15>;
> + vfront-porch = <15>;
> + vsync-len = <15>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + atmel: atmel_mxt_ts at 4b {
Node name should be generic.
> + compatible = "atmel,maxtouch";
> + reg = <0x4b>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <9 8>;
> + };
> +};
> +
> +&iomuxc {
> + ipu_disp1 {
LinusW queued patch 5fcdf6a7ed95 ("pinctrl: imx: Allow parsing DT
without function nodes") on pinctrl tree for 4.2 merge window. With
that, we can save one level of the sub-node.
> + pinctrl_ipu1_1_80Ohm_clk: ipudisp1grp {
The '1' suffix after 'ipu1' is meaningless. Please drop it. Also, will
you use other pad configuration for CLK for this board? Otherwise, the
suffix '_80Ohm_clk' can be saved too?
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x31
> + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xE1
> + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
> + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xE1
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xE1
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xE1
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xE1
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xE1
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xE1
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xE1
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xE1
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xE1
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xE1
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xE1
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xE1
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xE1
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xE1
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xe1
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xE1
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xE1
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xE1
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xE1
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xE1
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xE1
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xE1
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xE1
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xE1
> + >;
> + };
> + };
> +};
> +
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&display0_in>;
> +};
> diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
> new file mode 100644
> index 0000000..e1eaf5a
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
> @@ -0,0 +1,63 @@
> +/*
> + * support fot the imx6 based aristainetos2 board
> + *
> + * Copyright (C) 2015 Heiko Schocher <hs at denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
> +/dts-v1/;
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-aristainetos2.dtsi"
> +
> +/ {
> + model = "aristainetos2 i.MX6 Dual Lite Board 7";
> + compatible = "fsl,imx6dl";
> +
> + backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm1 0 3000>;
> + brightness-levels = <0 4 8 16 32 64 128 255>;
> + default-brightness-level = <6>;
> + };
> +
> + memory {
> + reg = <0x10000000 0x40000000>;
> + };
> +};
> +
> +&i2c3 {
> + atmel: atmel_mxt_ts at 4d {
> + compatible = "atmel,maxtouch";
> + reg = <0x4d>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <9 8>;
> + };
It seems the touch device is identical between
imx6dl-aristainetos2_4.dts and imx6dl-aristainetos2_7.dts. Why don't
you put it into imx6qdl-aristainetos2.dtsi?
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds-channel at 0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "okay";
> +
> + display-timings {
> + native-mode = <&timing0>;
> + timing0: 800x480p60 {
> + clock-frequency = <33246000>;
> + hactive = <800>;
> + vactive = <480>;
> + hfront-porch = <88>;
> + hback-porch = <88>;
> + hsync-len = <80>;
> + vback-porch = <10>;
> + vfront-porch = <10>;
> + vsync-len = <25>;
> + };
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
> new file mode 100644
> index 0000000..561dbea
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
> @@ -0,0 +1,627 @@
> +/*
> + * support fot the imx6 based aristainetos2 board
> + *
> + * Copyright (C) 2015 Heiko Schocher <hs at denx.de>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + regulators {
> + compatible = "simple-bus";
> +
> + reg_2p5v: 2p5v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P5V";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: 3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usbh1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 0 0>;
You included dt-bindings/gpio/gpio.h but did not use the macros?
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_aristainetos2_usbh1_vbus>;
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + reg_usbotg_vbus: usb-otg-vbus {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio4 15 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_aristainetos2_usbotg_vbus>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + status = "okay";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + status = "okay";
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <3>;
> + cs-gpios = <&gpio4 9 0 &gpio4 10 0 &gpio4 11 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + dma-names;
The dma-names should be a property with string value.
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + fsl,spi-num-chipselects = <2>;
> + cs-gpios = <&gpio2 26 0 &gpio2 27 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + dma-names;
> + status = "okay";
> +};
> +
> +&ecspi4 {
> + fsl,spi-num-chipselects = <2>;
> + cs-gpios = <&gpio3 29 0 &gpio5 2 0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi4>;
> + dma-names;
> + status = "okay";
> +
> + flash: m25p80 at 1 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "micron,n25q128a11";
> + spi-max-frequency = <20000000>;
> + reg = <1>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic at 58 {
> + compatible = "dialog,da9063";
> + reg = <0x58>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <04 0x8>;
> +
> + regulators {
> + bcore1 {
> + regulator-name = "bcore1";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + bcore2 {
> + regulator-name = "bcore2";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + bpro {
> + regulator-name = "bpro";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + bperi {
> + regulator-name = "bperi";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + bmem {
> + regulator-name = "bmem";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo2 {
> + regulator-name = "ldo2";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldo3 {
> + regulator-name = "ldo3";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo4 {
> + regulator-name = "ldo4";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo5 {
> + regulator-name = "ldo5";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo6 {
> + regulator-name = "ldo6";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo7 {
> + regulator-name = "ldo7";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo8 {
> + regulator-name = "ldo8";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo9 {
> + regulator-name = "ldo9";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo10 {
> + regulator-name = "ldo10";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo11 {
> + regulator-name = "ldo11";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + bio {
> + regulator-name = "bio";
> + regulator-always-on = <1>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> + };
> + };
Have a new line between nodes.
> + tmp103: tmp103 at 71 {
> + compatible = "ti,tmp103";
> + reg = <0x71>;
> + };
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + expander: tca6416 at 20 {
> + compatible = "ti,tca6416";
> + reg = <0x20>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + };
> +
> + rtc at 68 {
> + compatible = "dallas,m41t00";
> + reg = <0x68>;
> + };
> +};
> +
> +&i2c4 {
> + clocks = <&clks 116>;
Use macro for clock ID.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> + eeprom at 50{
> + compatible = "atmel,24c64";
> + reg = <0x50>;
> + };
Have new line between nodes.
> + eeprom at 57{
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + };
> +};
> +
> +&iomuxc {
I suggest you put iomuxc node at the bottom of the file to improve the
readability of the file.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight &pinctrl_gpio>;
These pins should be configured by client device node, not the hog
group.
> +
> + audmux {
> + pinctrl_audmux: audmux {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x80000000
> + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x80000000
> + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x80000000
> + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000
Provide a proper pad configuration value rather than 0x8000000.
> + >;
> + };
> + };
> +
> + backlight {
> + pinctrl_backlight: backlightgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0 /* backlight enable */
> + >;
> + };
> + };
> +
> + ecspi1 {
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x100b1 /* SS0# */
> + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1 /* SS1# */
> + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1 /* SS2# */
> + >;
> + };
> + };
> +
> + ecspi2 {
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x100b1 /* SS0# */
> + MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x100b1 /* SS1# */
> + >;
> + };
> + };
> +
> + ecspi4 {
> + pinctrl_ecspi4: ecspi4grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
> + MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
> + MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
> + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
> + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
> + MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x1b0b0 /* WP pin */
> + >;
> + };
> + };
> +
> + enet {
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + >;
> + };
> + };
> +
> + flexcan1 {
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
> + MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
> + >;
> + };
> + };
> +
> + flexcan2 {
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x80000000
> + MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x80000000
Ditto
> + >;
> + };
> + };
> +
> + gpio {
> + pinctrl_gpio: gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* led enable */
> + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* LCD power enable */
> + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0 /* led yellow */
> + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0 /* led red */
> + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b0 /* led green */
> + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0 /* led blue */
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* Profibus IRQ */
> + MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0 /* FPGA IRQ */
> + MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x1b0b0 /* spi bus #2 SS driver enable */
> + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 /* RST_LOC# PHY reset input (has pull-down!)*/
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b0b0 /* USB_OTG_ID = GPIO1_24*/
> + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* Touchscreen IRQ */
> + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b0 /* PCIe reset */
> + >;
> + };
> + };
> +
> + gpmi-nand {
> + pinctrl_gpmi_nand: gpmi-nand {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + >;
> + };
> + };
> +
> + i2c1 {
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> + >;
> + };
> + };
> +
> + i2c2 {
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> + };
> +
> + i2c3 {
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
> + };
> + };
> +
> + i2c4 {
> + pinctrl_i2c4: i2c4grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1
> + >;
> + };
> + };
> +
> + uart1 {
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x1b0b1
> + >;
> + };
> + };
> +
> + uart2 {
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
> + >;
> + };
> + };
> +
> + uart3 {
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
> + >;
> + };
> + };
> +
> + uart4 {
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> + };
> +
> + usbotg {
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> + >;
> + };
New line between nodes.
> + pinctrl_aristainetos2_usbh1_vbus: aristainetos-usbh1-vbus {
> + fsl,pins = <MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x130b0>;
> + };
> + pinctrl_aristainetos2_usbotg_vbus: aristainetos-usbotg-vbus {
> + fsl,pins = <MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x130b0>;
> + };
> + };
> +
> + usdhc1 {
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
> + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0 /* SD1 card detect input */
> + MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* SD1 write protect input */
> + >;
> + };
> + };
> +
> + usdhc2 {
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x71
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x71
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x71
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x71
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x71
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x71
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 /* SD2 level shifter output enable */
> + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* SD2 card detect input */
> + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SD2 write protect input */
> + >;
> + };
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio7 18 0>;
All the gpio properties need to be check for using the macros defined in
gpio.h.
Shawn
> + txd0-skew-ps = <0>;
> + txd1-skew-ps = <0>;
> + txd2-skew-ps = <0>;
> + txd3-skew-ps = <0>;
> + status = "okay";
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + status = "okay";
> +};
> +
> +&pcie {
> + reset-gpio = <&gpio2 16 0>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + fsl,uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usbh1_vbus>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usbotg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + disable-over-current;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + cd-gpios = <&gpio1 27 0>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + cd-gpios = <&gpio4 5 0>;
> + wp-gpios = <&gpio2 10 0>;
> + no-1-8-v;
> + status = "okay";
> +};
> --
> 2.1.0
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
More information about the linux-arm-kernel
mailing list