[PATCH 12/14] ARM: berlin: move BG2Q clock node
Sebastian Hesselbarth
sebastian.hesselbarth at gmail.com
Fri May 15 17:23:41 PDT 2015
From: Antoine Tenart <antoine.tenart at free-electrons.com>
With the introduction of the Berlin simple-mfd controller driver, all
drivers previously sharing the chip and system controller nodes now
have their own sub-node.
Signed-off-by: Antoine Tenart <antoine.tenart at free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
---
Cc: Stephen Boyd <sboyd at codeaurora.org>
---
arch/arm/boot/dts/berlin2q.dtsi | 50 ++++++++++++++++++++++-------------------
1 file changed, 27 insertions(+), 23 deletions(-)
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 8715d11c8f76..4a21ba386230 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -74,7 +74,7 @@
sdhci0: sdhci at ab0000 {
compatible = "mrvl,pxav3-mmc";
reg = <0xab0000 0x200>;
- clocks = <&chip CLKID_SDIO1XIN>;
+ clocks = <&chip_clk CLKID_SDIO1XIN>;
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
@@ -82,7 +82,7 @@
sdhci1: sdhci at ab0800 {
compatible = "mrvl,pxav3-mmc";
reg = <0xab0800 0x200>;
- clocks = <&chip CLKID_SDIO1XIN>;
+ clocks = <&chip_clk CLKID_SDIO1XIN>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
@@ -91,7 +91,7 @@
compatible = "mrvl,pxav3-mmc";
reg = <0xab1000 0x200>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip CLKID_NFC_ECC>, <&chip CLKID_NFC>;
+ clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_NFC>;
clock-names = "io", "core";
status = "disabled";
};
@@ -112,7 +112,7 @@
local-timer at ad0600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0xad0600 0x20>;
- clocks = <&chip CLKID_TWD>;
+ clocks = <&chip_clk CLKID_TWD>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
@@ -135,7 +135,7 @@
compatible = "chipidea,usb2";
reg = <0xa30000 0x10000>;
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip CLKID_USB2>;
+ clocks = <&chip_clk CLKID_USB2>;
phys = <&usb_phy2>;
phy-names = "usb-phy";
status = "disabled";
@@ -160,7 +160,7 @@
eth0: ethernet at b90000 {
compatible = "marvell,pxa168-eth";
reg = <0xb90000 0x10000>;
- clocks = <&chip CLKID_GETH0>;
+ clocks = <&chip_clk CLKID_GETH0>;
interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
/* set by bootloader */
local-mac-address = [00 00 00 00 00 00];
@@ -267,7 +267,7 @@
reg = <0x1400 0x100>;
interrupt-parent = <&aic>;
interrupts = <4>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
pinctrl-0 = <&twsi0_pmux>;
pinctrl-names = "default";
status = "disabled";
@@ -280,7 +280,7 @@
reg = <0x1800 0x100>;
interrupt-parent = <&aic>;
interrupts = <5>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
pinctrl-0 = <&twsi1_pmux>;
pinctrl-names = "default";
status = "disabled";
@@ -289,7 +289,7 @@
timer0: timer at 2c00 {
compatible = "snps,dw-apb-timer";
reg = <0x2c00 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
interrupts = <8>;
};
@@ -297,14 +297,14 @@
timer1: timer at 2c14 {
compatible = "snps,dw-apb-timer";
reg = <0x2c14 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
};
timer2: timer at 2c28 {
compatible = "snps,dw-apb-timer";
reg = <0x2c28 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -312,7 +312,7 @@
timer3: timer at 2c3c {
compatible = "snps,dw-apb-timer";
reg = <0x2c3c 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -320,7 +320,7 @@
timer4: timer at 2c50 {
compatible = "snps,dw-apb-timer";
reg = <0x2c50 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -328,7 +328,7 @@
timer5: timer at 2c64 {
compatible = "snps,dw-apb-timer";
reg = <0x2c64 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -336,7 +336,7 @@
timer6: timer at 2c78 {
compatible = "snps,dw-apb-timer";
reg = <0x2c78 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -344,7 +344,7 @@
timer7: timer at 2c8c {
compatible = "snps,dw-apb-timer";
reg = <0x2c8c 0x14>;
- clocks = <&chip CLKID_CFG>;
+ clocks = <&chip_clk CLKID_CFG>;
clock-names = "timer";
status = "disabled";
};
@@ -361,10 +361,14 @@
chip: chip-control at ea0000 {
compatible = "marvell,berlin2q-chip-ctrl", "simple-mfd", "syscon";
- #clock-cells = <1>;
reg = <0xea0000 0x400>, <0xdd0170 0x10>;
- clocks = <&refclk>;
- clock-names = "refclk";
+
+ chip_clk: clock {
+ compatible = "marvell,berlin2q-clk";
+ #clock-cells = <1>;
+ clocks = <&refclk>;
+ clock-names = "refclk";
+ };
soc_pinctrl: pin-controller {
compatible = "marvell,berlin2q-soc-pinctrl";
@@ -389,7 +393,7 @@
compatible = "marvell,berlin2q-ahci", "generic-ahci";
reg = <0xe90000 0x1000>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip CLKID_SATA>;
+ clocks = <&chip_clk CLKID_SATA>;
#address-cells = <1>;
#size-cells = <0>;
@@ -409,7 +413,7 @@
sata_phy: phy at e900a0 {
compatible = "marvell,berlin2q-sata-phy";
reg = <0xe900a0 0x200>;
- clocks = <&chip CLKID_SATA>;
+ clocks = <&chip_clk CLKID_SATA>;
#address-cells = <1>;
#size-cells = <0>;
#phy-cells = <1>;
@@ -428,7 +432,7 @@
compatible = "chipidea,usb2";
reg = <0xed0000 0x10000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip CLKID_USB0>;
+ clocks = <&chip_clk CLKID_USB0>;
phys = <&usb_phy0>;
phy-names = "usb-phy";
status = "disabled";
@@ -438,7 +442,7 @@
compatible = "chipidea,usb2";
reg = <0xee0000 0x10000>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip CLKID_USB1>;
+ clocks = <&chip_clk CLKID_USB1>;
phys = <&usb_phy1>;
phy-names = "usb-phy";
status = "disabled";
--
2.1.0
More information about the linux-arm-kernel
mailing list