[PATCH v2 3/5] clk: add support for clocks provided by SCP(System Control Processor)
Sudeep Holla
sudeep.holla at arm.com
Thu May 14 08:42:33 PDT 2015
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Power Interface(SCPI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCPI
protocol.
Signed-off-by: Sudeep Holla <sudeep.holla at arm.com>
Cc: Mike Turquette <mturquette at linaro.org>
Cc: Stephen Boyd <sboyd at codeaurora.org>
Cc: Liviu Dudau <Liviu.Dudau at arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
Cc: Jon Medhurst (Tixy) <tixy at linaro.org>
Cc: linux-clk at vger.kernel.org
---
drivers/clk/Kconfig | 10 ++
drivers/clk/Makefile | 1 +
drivers/clk/clk-scpi.c | 293 +++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 304 insertions(+)
create mode 100644 drivers/clk/clk-scpi.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 9897f353bf1a..67e5c6469731 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -59,6 +59,16 @@ config COMMON_CLK_RK808
clocked at 32KHz each. Clkout1 is always on, Clkout2 can off
by control register.
+config COMMON_CLK_SCPI
+ tristate "Clock driver controlled via SCPI interface"
+ depends on ARM_SCPI_PROTOCOL
+ ---help---
+ This driver provides support for clocks that are controlled
+ by firmware that implements the SCPI interface.
+
+ This driver uses SCPI Message Protocol to interact with the
+ firmware providing all the clock controls.
+
config COMMON_CLK_SI5351
tristate "Clock driver for SiLabs 5351A/B/C"
depends on I2C
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 3d00c25382c5..442ab6ebd5b1 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_COMMON_CLK_PALMAS) += clk-palmas.o
obj-$(CONFIG_CLK_QORIQ) += clk-qoriq.o
obj-$(CONFIG_COMMON_CLK_RK808) += clk-rk808.o
obj-$(CONFIG_COMMON_CLK_S2MPS11) += clk-s2mps11.o
+obj-$(CONFIG_COMMON_CLK_SCPI) += clk-scpi.o
obj-$(CONFIG_COMMON_CLK_SI5351) += clk-si5351.o
obj-$(CONFIG_COMMON_CLK_SI570) += clk-si570.o
obj-$(CONFIG_CLK_TWL6040) += clk-twl6040.o
diff --git a/drivers/clk/clk-scpi.c b/drivers/clk/clk-scpi.c
new file mode 100644
index 000000000000..208f68d14214
--- /dev/null
+++ b/drivers/clk/clk-scpi.c
@@ -0,0 +1,293 @@
+/*
+ * System Control and Power Interface (SCPI) Protocol based clock driver
+ *
+ * Copyright (C) 2015 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/scpi_protocol.h>
+
+struct scpi_clk {
+ u32 id;
+ const char *name;
+ struct clk_hw hw;
+ struct scpi_dvfs_info *info;
+ unsigned long rate_min;
+ unsigned long rate_max;
+};
+
+#define to_scpi_clk(clk) container_of(clk, struct scpi_clk, hw)
+
+static struct scpi_ops *scpi_ops;
+
+static unsigned long scpi_clk_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+
+ return scpi_ops->clk_get_val(clk->id);
+}
+
+static long scpi_clk_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+
+ if (WARN_ON(clk->rate_min && rate < clk->rate_min))
+ rate = clk->rate_min;
+ if (WARN_ON(clk->rate_max && rate > clk->rate_max))
+ rate = clk->rate_max;
+
+ return rate;
+}
+
+static int scpi_clk_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+
+ return scpi_ops->clk_set_val(clk->id, rate);
+}
+
+static struct clk_ops scpi_clk_ops = {
+ .recalc_rate = scpi_clk_recalc_rate,
+ .round_rate = scpi_clk_round_rate,
+ .set_rate = scpi_clk_set_rate,
+};
+
+/* find closest match to given frequency in OPP table */
+static int __scpi_dvfs_round_rate(struct scpi_clk *clk, unsigned long rate)
+{
+ int idx;
+ u32 fmin = 0, fmax = ~0, ftmp;
+ struct scpi_opp *opp = clk->info->opps;
+
+ for (idx = 0; idx < clk->info->count; idx++, opp++) {
+ ftmp = opp->freq;
+ if (ftmp >= (u32)rate) {
+ if (ftmp <= fmax)
+ fmax = ftmp;
+ break;
+ } else if (ftmp >= fmin) {
+ fmin = ftmp;
+ }
+ }
+ return fmax != ~0 ? fmax : fmin;
+}
+
+static unsigned long scpi_dvfs_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+ int idx = scpi_ops->dvfs_get_idx(clk->id);
+ struct scpi_opp *opp;
+
+ if (idx < 0)
+ return 0;
+
+ opp = clk->info->opps + idx;
+ return opp->freq;
+}
+
+static long scpi_dvfs_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+
+ return __scpi_dvfs_round_rate(clk, rate);
+}
+
+static int __scpi_find_dvfs_index(struct scpi_clk *clk, unsigned long rate)
+{
+ int idx, max_opp = clk->info->count;
+ struct scpi_opp *opp = clk->info->opps;
+
+ for (idx = 0; idx < max_opp; idx++, opp++)
+ if (opp->freq == rate)
+ return idx;
+ return -EINVAL;
+}
+
+static int scpi_dvfs_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct scpi_clk *clk = to_scpi_clk(hw);
+ int ret = __scpi_find_dvfs_index(clk, rate);
+
+ if (ret < 0)
+ return ret;
+ return scpi_ops->dvfs_set_idx(clk->id, (u8)ret);
+}
+
+static struct clk_ops scpi_dvfs_ops = {
+ .recalc_rate = scpi_dvfs_recalc_rate,
+ .round_rate = scpi_dvfs_round_rate,
+ .set_rate = scpi_dvfs_set_rate,
+};
+
+static const struct of_device_id scpi_clk_match[] = {
+ { .compatible = "arm,scpi-dvfs", .data = &scpi_dvfs_ops, },
+ { .compatible = "arm,scpi-clk", .data = &scpi_clk_ops, },
+ {}
+};
+
+static struct clk *
+scpi_clk_ops_init(struct device *dev, struct device_node *np,
+ struct scpi_clk *sclk)
+{
+ struct clk_init_data init;
+
+ init.name = sclk->name;
+ init.flags = CLK_IS_ROOT;
+ init.num_parents = 0;
+ init.ops = of_match_node(scpi_clk_match, np)->data;
+ sclk->hw.init = &init;
+
+ if (init.ops == &scpi_dvfs_ops) {
+ struct scpi_dvfs_info *info = scpi_ops->dvfs_get_info(sclk->id);
+
+ if (IS_ERR(info))
+ return NULL;
+ sclk->info = info;
+ } else if (init.ops == &scpi_clk_ops) {
+ int ret = scpi_ops->clk_get_range(sclk->id, &sclk->rate_min,
+ &sclk->rate_max);
+ if (ret || !sclk->rate_max)
+ return NULL;
+ } else {
+ return NULL;
+ }
+
+ return devm_clk_register(dev, &sclk->hw);
+}
+
+static int scpi_clk_add(struct device *dev, struct device_node *np)
+{
+ struct clk **clks;
+ int idx, count;
+ struct clk_onecell_data *clk_data;
+
+ count = of_property_count_strings(np, "clock-output-names");
+ if (count < 0) {
+ dev_err(dev, "%s: invalid clock output count\n", np->name);
+ return -EINVAL;
+ }
+
+ clk_data = devm_kmalloc(dev, sizeof(*clk_data), GFP_KERNEL);
+ if (!clk_data) {
+ dev_err(dev, "failed to allocate clock provider data\n");
+ return -ENOMEM;
+ }
+
+ clks = devm_kmalloc(dev, count * sizeof(*clks), GFP_KERNEL);
+ if (!clks) {
+ dev_err(dev, "failed to allocate clock providers\n");
+ return -ENOMEM;
+ }
+
+ for (idx = 0; idx < count; idx++) {
+ struct scpi_clk *sclk;
+ u32 val;
+
+ sclk = devm_kzalloc(dev, sizeof(*sclk), GFP_KERNEL);
+ if (!sclk) {
+ dev_err(dev, "failed to allocate scpi clocks\n");
+ return -ENOMEM;
+ }
+
+ if (of_property_read_string_index(np, "clock-output-names",
+ idx, &sclk->name)) {
+ dev_err(dev, "invalid clock name @ %s\n", np->name);
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32_index(np, "clock-indices",
+ idx, &val)) {
+ dev_err(dev, "invalid clock index @ %s\n", np->name);
+ return -EINVAL;
+ }
+
+ sclk->id = val;
+
+ clks[idx] = scpi_clk_ops_init(dev, np, sclk);
+ if (IS_ERR_OR_NULL(clks[idx]))
+ dev_err(dev, "failed to register clock '%s'\n",
+ sclk->name);
+ else
+ dev_dbg(dev, "Registered clock '%s'\n", sclk->name);
+ }
+
+ clk_data->clks = clks;
+ clk_data->clk_num = idx;
+ of_clk_add_provider(np, of_clk_src_onecell_get, clk_data);
+
+ return 0;
+}
+
+static int scpi_clocks_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *child, *np = dev->of_node;
+
+ for_each_available_child_of_node(np, child)
+ of_clk_del_provider(np);
+ scpi_ops = NULL;
+ return 0;
+}
+
+static int scpi_clocks_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct device *dev = &pdev->dev;
+ struct device_node *child, *np = dev->of_node;
+
+ scpi_ops = get_scpi_ops();
+ if (!scpi_ops)
+ return -ENXIO;
+
+ for_each_available_child_of_node(np, child) {
+ ret = scpi_clk_add(dev, child);
+ if (ret) {
+ scpi_clocks_remove(pdev);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static const struct of_device_id scpi_clocks_ids[] = {
+ { .compatible = "arm,scpi-clocks", },
+ {}
+};
+
+static struct platform_driver scpi_clocks_driver = {
+ .driver = {
+ .name = "scpi_clocks",
+ .of_match_table = scpi_clocks_ids,
+ },
+ .probe = scpi_clocks_probe,
+ .remove = scpi_clocks_remove,
+};
+module_platform_driver(scpi_clocks_driver);
+
+MODULE_AUTHOR("Sudeep Holla <sudeep.holla at arm.com>");
+MODULE_DESCRIPTION("ARM SCPI clock driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
More information about the linux-arm-kernel
mailing list