[PATCH v3 4/5] phy: add Broadcom SATA3 PHY driver for Broadcom STB SoCs
Kishon Vijay Abraham I
kishon at ti.com
Wed May 13 22:52:55 PDT 2015
Hi,
On Thursday 14 May 2015 12:19 AM, Brian Norris wrote:
> On Wed, May 13, 2015 at 04:37:05PM +0530, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Wednesday 13 May 2015 04:58 AM, Brian Norris wrote:
>>> Supports up to two ports which can each be powered on/off and configured
>>> independently.
>>>
>>> Signed-off-by: Brian Norris <computersforpeace at gmail.com>
>>
>> couple of minor comments below
>>> ---
>>> v3: no change
>>>
>>> v2:
>>> - stop sharing SATA_TOP_CTRL registers with SATA driver
>>> - kill custom xlate function
>>>
>>> drivers/phy/Kconfig | 9 ++
>>> drivers/phy/Makefile | 1 +
>>> drivers/phy/phy-brcmstb-sata.c | 216 +++++++++++++++++++++++++++++++++++++++++
>>> 3 files changed, 226 insertions(+)
>>> create mode 100644 drivers/phy/phy-brcmstb-sata.c
>>>
>>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>>> index a53bd5b52df9..36788b6f0220 100644
>>> --- a/drivers/phy/Kconfig
>>> +++ b/drivers/phy/Kconfig
>>> @@ -309,4 +309,13 @@ config PHY_QCOM_UFS
>>> help
>>> Support for UFS PHY on QCOM chipsets.
>>>
>>> +config PHY_BRCMSTB_SATA
>>> + tristate "Broadcom STB SATA PHY driver"
>>> + depends on ARCH_BRCMSTB
>>> + depends on OF
>>> + select GENERIC_PHY
>>> + help
>>> + Enable this to support the SATA3 PHY on 28nm Broadcom STB SoCs.
>>> + Likely useful only with CONFIG_SATA_BRCMSTB enabled.
>>> +
>>> endmenu
>>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>>> index f12625178780..c61f3fdd191e 100644
>>> --- a/drivers/phy/Makefile
>>> +++ b/drivers/phy/Makefile
>>> @@ -40,3 +40,4 @@ obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
>>> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
>>> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
>>> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
>>> +obj-$(CONFIG_PHY_BRCMSTB_SATA) += phy-brcmstb-sata.o
>>> diff --git a/drivers/phy/phy-brcmstb-sata.c b/drivers/phy/phy-brcmstb-sata.c
>>> new file mode 100644
>>> index 000000000000..8387c8cbea8c
>>> --- /dev/null
>>> +++ b/drivers/phy/phy-brcmstb-sata.c
>>> @@ -0,0 +1,216 @@
>>> +/*
>>> + * Broadcom SATA3 AHCI Controller PHY Driver
>>> + *
>>> + * Copyright © 2009-2015 Broadcom Corporation
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License as published by
>>> + * the Free Software Foundation; either version 2, or (at your option)
>>> + * any later version.
>>> + *
>>> + * This program is distributed in the hope that it will be useful,
>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>> + * GNU General Public License for more details.
>>> + */
>>> +
>>> +#include <linux/device.h>
>>> +#include <linux/init.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/io.h>
>>> +#include <linux/kernel.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/phy/phy.h>
>>> +#include <linux/platform_device.h>
>>> +
>>> +#define SATA_MDIO_BANK_OFFSET 0x23c
>>> +#define SATA_MDIO_REG_OFFSET(ofs) ((ofs) * 4)
>>> +#define SATA_MDIO_REG_SPACE_SIZE 0x1000
>>> +#define SATA_MDIO_REG_LENGTH 0x1f00
>>> +
>>> +#define MAX_PORTS 2
>>> +
>>> +/* Register offset between PHYs in PCB space */
>>> +#define SATA_MDIO_REG_SPACE_SIZE 0x1000
>>> +
>>> +struct brcm_sata_port {
>>> + int portnum;
>>> + struct phy *phy;
>>> + struct brcm_sata_phy *phy_priv;
>>> + bool ssc_en;
>>> +};
>>> +
>>> +struct brcm_sata_phy {
>>> + struct device *dev;
>>> + void __iomem *phy_base;
>>> +
>>> + struct brcm_sata_port phys[MAX_PORTS];
>>> +};
>>> +
>>> +enum sata_mdio_phy_regs_28nm {
>>
>> Why should these defines be in enum?
>
> Why not? They're logically grouped this way, and IMO, they look nicer.
> You can see drivers/ata/ahci.h for a similar example.
fair enough.
>
>>> + PLL_REG_BANK_0 = 0x50,
>>> + PLL_REG_BANK_0_PLLCONTROL_0 = 0x81,
>>> +
>>> + TXPMD_REG_BANK = 0x1a0,
>>> + TXPMD_CONTROL1 = 0x81,
>>> + TXPMD_CONTROL1_TX_SSC_EN_FRC = BIT(0),
>>> + TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL = BIT(1),
>>> + TXPMD_TX_FREQ_CTRL_CONTROL1 = 0x82,
>>> + TXPMD_TX_FREQ_CTRL_CONTROL2 = 0x83,
>>> + TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK = 0x3ff,
>>> + TXPMD_TX_FREQ_CTRL_CONTROL3 = 0x84,
>>> + TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK = 0x3ff,
>>> +};
>>> +
>>> +static inline void __iomem *brcm_sata_phy_base(struct brcm_sata_port *port)
>>> +{
>>> + struct brcm_sata_phy *priv = port->phy_priv;
>>> +
>>> + return priv->phy_base + (port->portnum * SATA_MDIO_REG_SPACE_SIZE);
>>> +}
>>> +
>>> +static void brcm_sata_mdio_wr(void __iomem *addr, u32 bank, u32 ofs,
>>> + u32 msk, u32 value)
>>> +{
>>> + u32 tmp;
>>> +
>>> + writel(bank, addr + SATA_MDIO_BANK_OFFSET);
>>> + tmp = readl(addr + SATA_MDIO_REG_OFFSET(ofs));
>>> + tmp = (tmp & msk) | value;
>>> + writel(tmp, addr + SATA_MDIO_REG_OFFSET(ofs));
>>> +}
>>> +
>>> +/* These defaults were characterized by H/W group */
>>> +#define FMIN_VAL_DEFAULT 0x3df
>>> +#define FMAX_VAL_DEFAULT 0x3df
>>> +#define FMAX_VAL_SSC 0x83
>>> +
>>> +static void cfg_ssc_28nm(struct brcm_sata_port *port)
>>
>> brcm_sata_cfg_ssc_28nm to make it similar to other functions.
>
> OK.
>
>>> +{
>>> + void __iomem *base = brcm_sata_phy_base(port);
>>> + struct brcm_sata_phy *priv = port->phy_priv;
>>> + u32 tmp;
>>> +
>>> + /* override the TX spread spectrum setting */
>>> + tmp = TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL | TXPMD_CONTROL1_TX_SSC_EN_FRC;
>>> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_CONTROL1, ~tmp, tmp);
>>> +
>>> + /* set fixed min freq */
>>> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL2,
>>> + ~TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK,
>>> + FMIN_VAL_DEFAULT);
>>> +
>>> + /* set fixed max freq depending on SSC config */
>>> + if (port->ssc_en) {
>>> + dev_info(priv->dev, "enabling SSC on port %d\n", port->portnum);
>>> + tmp = FMAX_VAL_SSC;
>>> + } else {
>>> + tmp = FMAX_VAL_DEFAULT;
>>> + }
>>> +
>>> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL3,
>>> + ~TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK, tmp);
>>> +}
>>> +
>>> +static int brcm_sata_phy_init(struct phy *phy)
>>> +{
>>> + struct brcm_sata_port *port = phy_get_drvdata(phy);
>>> +
>>> + cfg_ssc_28nm(port);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static struct phy_ops phy_ops_28nm = {
>>> + .init = brcm_sata_phy_init,
>>> + .owner = THIS_MODULE,
>>> +};
>>> +
>>> +static const struct of_device_id brcm_sata_phy_of_match[] = {
>>> + { .compatible = "brcm,bcm7445-sata-phy" },
>>> + {},
>>> +};
>>> +MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
>>> +
>>> +static int brcm_sata_phy_probe(struct platform_device *pdev)
>>> +{
>>> + struct device *dev = &pdev->dev;
>>> + struct device_node *dn = dev->of_node, *child;
>>> + struct brcm_sata_phy *priv;
>>> + struct resource *res;
>>> + struct phy_provider *provider;
>>> + int count = 0;
>>> +
>>> + if (of_get_child_count(dn) == 0)
>>> + return -ENODEV;
>>> +
>>> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
>>> + if (!priv)
>>> + return -ENOMEM;
>>> + dev_set_drvdata(dev, priv);
>>> + priv->dev = dev;
>>> +
>>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy");
>>> + priv->phy_base = devm_ioremap_resource(dev, res);
>>> + if (IS_ERR(priv->phy_base))
>>> + return PTR_ERR(priv->phy_base);
>>> +
>>> + for_each_available_child_of_node(dn, child) {
>>> + unsigned int id;
>>> + struct brcm_sata_port *port;
>>> +
>>> + if (of_property_read_u32(child, "reg", &id)) {
>>> + dev_err(dev, "missing reg property in node %s\n",
>>> + child->name);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + if (id >= MAX_PORTS) {
>>> + dev_err(dev, "invalid reg: %u\n", id);
>>> + return -EINVAL;
>>> + }
>>> + if (priv->phys[id].phy) {
>>> + dev_err(dev, "already registered port %u\n", id);
>>> + return -EINVAL;
>>> + }
>>> +
>>> + port = &priv->phys[id];
>>> + port->portnum = id;
>>> + port->phy_priv = priv;
>>> + port->phy = devm_phy_create(dev, child, &phy_ops_28nm);
>>> + port->ssc_en = of_property_read_bool(child, "brcm,enable-ssc");
>>> + if (IS_ERR(port->phy)) {
>>> + dev_err(dev, "failed to create PHY\n");
>>> + return PTR_ERR(port->phy);
>>> + }
>>> +
>>> + phy_set_drvdata(port->phy, port);
>>> + count++;
>>> + }
>>> +
>>> + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>>> + if (IS_ERR(provider)) {
>>> + dev_err(dev, "could not register PHY provider\n");
>>> + return PTR_ERR(provider);
>>> + }
>>> +
>>> + dev_info(dev, "registered %d port(s)\n", count);
>>
>> lets not make the boot noisy. Change to dev_dbg?
>
> Why? What's the harm? And I thought we discussed this already. "Noisy"
> depends on your point of view; IMO, this is important information. If
> for some reason this driver wasn't loaded or probed, we'd want to know.
> Besides, dev_dbg() requires you to fiddle with both the log level and
> the dynamic debug boot parameters just to get these informational
> messages.
so be it. While sending the next version please also add a MAINTAINERs entry
for this driver.
Cheers
Kishon
More information about the linux-arm-kernel
mailing list