[PATCH v3 4/5] phy: add Broadcom SATA3 PHY driver for Broadcom STB SoCs
Kishon Vijay Abraham I
kishon at ti.com
Wed May 13 04:07:05 PDT 2015
Hi,
On Wednesday 13 May 2015 04:58 AM, Brian Norris wrote:
> Supports up to two ports which can each be powered on/off and configured
> independently.
>
> Signed-off-by: Brian Norris <computersforpeace at gmail.com>
couple of minor comments below
> ---
> v3: no change
>
> v2:
> - stop sharing SATA_TOP_CTRL registers with SATA driver
> - kill custom xlate function
>
> drivers/phy/Kconfig | 9 ++
> drivers/phy/Makefile | 1 +
> drivers/phy/phy-brcmstb-sata.c | 216 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 226 insertions(+)
> create mode 100644 drivers/phy/phy-brcmstb-sata.c
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a53bd5b52df9..36788b6f0220 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -309,4 +309,13 @@ config PHY_QCOM_UFS
> help
> Support for UFS PHY on QCOM chipsets.
>
> +config PHY_BRCMSTB_SATA
> + tristate "Broadcom STB SATA PHY driver"
> + depends on ARCH_BRCMSTB
> + depends on OF
> + select GENERIC_PHY
> + help
> + Enable this to support the SATA3 PHY on 28nm Broadcom STB SoCs.
> + Likely useful only with CONFIG_SATA_BRCMSTB enabled.
> +
> endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index f12625178780..c61f3fdd191e 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -40,3 +40,4 @@ obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
> obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
> +obj-$(CONFIG_PHY_BRCMSTB_SATA) += phy-brcmstb-sata.o
> diff --git a/drivers/phy/phy-brcmstb-sata.c b/drivers/phy/phy-brcmstb-sata.c
> new file mode 100644
> index 000000000000..8387c8cbea8c
> --- /dev/null
> +++ b/drivers/phy/phy-brcmstb-sata.c
> @@ -0,0 +1,216 @@
> +/*
> + * Broadcom SATA3 AHCI Controller PHY Driver
> + *
> + * Copyright © 2009-2015 Broadcom Corporation
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2, or (at your option)
> + * any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/device.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +
> +#define SATA_MDIO_BANK_OFFSET 0x23c
> +#define SATA_MDIO_REG_OFFSET(ofs) ((ofs) * 4)
> +#define SATA_MDIO_REG_SPACE_SIZE 0x1000
> +#define SATA_MDIO_REG_LENGTH 0x1f00
> +
> +#define MAX_PORTS 2
> +
> +/* Register offset between PHYs in PCB space */
> +#define SATA_MDIO_REG_SPACE_SIZE 0x1000
> +
> +struct brcm_sata_port {
> + int portnum;
> + struct phy *phy;
> + struct brcm_sata_phy *phy_priv;
> + bool ssc_en;
> +};
> +
> +struct brcm_sata_phy {
> + struct device *dev;
> + void __iomem *phy_base;
> +
> + struct brcm_sata_port phys[MAX_PORTS];
> +};
> +
> +enum sata_mdio_phy_regs_28nm {
Why should these defines be in enum?
> + PLL_REG_BANK_0 = 0x50,
> + PLL_REG_BANK_0_PLLCONTROL_0 = 0x81,
> +
> + TXPMD_REG_BANK = 0x1a0,
> + TXPMD_CONTROL1 = 0x81,
> + TXPMD_CONTROL1_TX_SSC_EN_FRC = BIT(0),
> + TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL = BIT(1),
> + TXPMD_TX_FREQ_CTRL_CONTROL1 = 0x82,
> + TXPMD_TX_FREQ_CTRL_CONTROL2 = 0x83,
> + TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK = 0x3ff,
> + TXPMD_TX_FREQ_CTRL_CONTROL3 = 0x84,
> + TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK = 0x3ff,
> +};
> +
> +static inline void __iomem *brcm_sata_phy_base(struct brcm_sata_port *port)
> +{
> + struct brcm_sata_phy *priv = port->phy_priv;
> +
> + return priv->phy_base + (port->portnum * SATA_MDIO_REG_SPACE_SIZE);
> +}
> +
> +static void brcm_sata_mdio_wr(void __iomem *addr, u32 bank, u32 ofs,
> + u32 msk, u32 value)
> +{
> + u32 tmp;
> +
> + writel(bank, addr + SATA_MDIO_BANK_OFFSET);
> + tmp = readl(addr + SATA_MDIO_REG_OFFSET(ofs));
> + tmp = (tmp & msk) | value;
> + writel(tmp, addr + SATA_MDIO_REG_OFFSET(ofs));
> +}
> +
> +/* These defaults were characterized by H/W group */
> +#define FMIN_VAL_DEFAULT 0x3df
> +#define FMAX_VAL_DEFAULT 0x3df
> +#define FMAX_VAL_SSC 0x83
> +
> +static void cfg_ssc_28nm(struct brcm_sata_port *port)
brcm_sata_cfg_ssc_28nm to make it similar to other functions.
> +{
> + void __iomem *base = brcm_sata_phy_base(port);
> + struct brcm_sata_phy *priv = port->phy_priv;
> + u32 tmp;
> +
> + /* override the TX spread spectrum setting */
> + tmp = TXPMD_CONTROL1_TX_SSC_EN_FRC_VAL | TXPMD_CONTROL1_TX_SSC_EN_FRC;
> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_CONTROL1, ~tmp, tmp);
> +
> + /* set fixed min freq */
> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL2,
> + ~TXPMD_TX_FREQ_CTRL_CONTROL2_FMIN_MASK,
> + FMIN_VAL_DEFAULT);
> +
> + /* set fixed max freq depending on SSC config */
> + if (port->ssc_en) {
> + dev_info(priv->dev, "enabling SSC on port %d\n", port->portnum);
> + tmp = FMAX_VAL_SSC;
> + } else {
> + tmp = FMAX_VAL_DEFAULT;
> + }
> +
> + brcm_sata_mdio_wr(base, TXPMD_REG_BANK, TXPMD_TX_FREQ_CTRL_CONTROL3,
> + ~TXPMD_TX_FREQ_CTRL_CONTROL3_FMAX_MASK, tmp);
> +}
> +
> +static int brcm_sata_phy_init(struct phy *phy)
> +{
> + struct brcm_sata_port *port = phy_get_drvdata(phy);
> +
> + cfg_ssc_28nm(port);
> +
> + return 0;
> +}
> +
> +static struct phy_ops phy_ops_28nm = {
> + .init = brcm_sata_phy_init,
> + .owner = THIS_MODULE,
> +};
> +
> +static const struct of_device_id brcm_sata_phy_of_match[] = {
> + { .compatible = "brcm,bcm7445-sata-phy" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, brcm_sata_phy_of_match);
> +
> +static int brcm_sata_phy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct device_node *dn = dev->of_node, *child;
> + struct brcm_sata_phy *priv;
> + struct resource *res;
> + struct phy_provider *provider;
> + int count = 0;
> +
> + if (of_get_child_count(dn) == 0)
> + return -ENODEV;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> + dev_set_drvdata(dev, priv);
> + priv->dev = dev;
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy");
> + priv->phy_base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(priv->phy_base))
> + return PTR_ERR(priv->phy_base);
> +
> + for_each_available_child_of_node(dn, child) {
> + unsigned int id;
> + struct brcm_sata_port *port;
> +
> + if (of_property_read_u32(child, "reg", &id)) {
> + dev_err(dev, "missing reg property in node %s\n",
> + child->name);
> + return -EINVAL;
> + }
> +
> + if (id >= MAX_PORTS) {
> + dev_err(dev, "invalid reg: %u\n", id);
> + return -EINVAL;
> + }
> + if (priv->phys[id].phy) {
> + dev_err(dev, "already registered port %u\n", id);
> + return -EINVAL;
> + }
> +
> + port = &priv->phys[id];
> + port->portnum = id;
> + port->phy_priv = priv;
> + port->phy = devm_phy_create(dev, child, &phy_ops_28nm);
> + port->ssc_en = of_property_read_bool(child, "brcm,enable-ssc");
> + if (IS_ERR(port->phy)) {
> + dev_err(dev, "failed to create PHY\n");
> + return PTR_ERR(port->phy);
> + }
> +
> + phy_set_drvdata(port->phy, port);
> + count++;
> + }
> +
> + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> + if (IS_ERR(provider)) {
> + dev_err(dev, "could not register PHY provider\n");
> + return PTR_ERR(provider);
> + }
> +
> + dev_info(dev, "registered %d port(s)\n", count);
lets not make the boot noisy. Change to dev_dbg?
Thanks
Kishon
More information about the linux-arm-kernel
mailing list