[PATCH v5 2/2] ARM: at91/dt: add support for kizboxmini

[Gaël PORTAY]

Thanks

Sent from my Cyanogen phone

On May 11, 2015 11:17 AM, Nicolas Ferre <nicolas.ferre at atmel.com> wrote:
>
> Le 04/05/2015 17:59, Gaël PORTAY a écrit : 
> > Add DT file for Kizbox mini board. 
> > This board is based on Atmel's AT91SAM9G25 SoC. 
> > 
> > Signed-off-by: Gaël PORTAY <g.portay at overkiz.com> 
> > Acked-by: Boris Brezillon <boris.brezillon at free-electrons.com> 
> > Acked-by: Alexandre Belloni <alexandre.belloni at free-electrons.com> 
>
> Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com> 
> Nitpicking below... 
>
> > --- 
> >  arch/arm/boot/dts/Makefile            |   1 + 
> >  arch/arm/boot/dts/at91-kizboxmini.dts | 130 ++++++++++++++++++++++++++++++++++ 
> >  2 files changed, 131 insertions(+) 
> >  create mode 100644 arch/arm/boot/dts/at91-kizboxmini.dts 
> > 
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile 
> > index 21726fd..4bf72c0 100644 
> > --- a/arch/arm/boot/dts/Makefile 
> > +++ b/arch/arm/boot/dts/Makefile 
> > @@ -30,6 +30,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \ 
> >  at91sam9rlek.dtb \ 
> >  at91-ariag25.dtb \ 
> >  at91-cosino_mega2560.dtb \ 
> > + at91-kizboxmini.dtb \ 
> >  at91sam9g15ek.dtb \ 
> >  at91sam9g25ek.dtb \ 
> >  at91sam9g35ek.dtb \ 
> > diff --git a/arch/arm/boot/dts/at91-kizboxmini.dts b/arch/arm/boot/dts/at91-kizboxmini.dts 
> > new file mode 100644 
> > index 0000000..7a899ca 
> > --- /dev/null 
> > +++ b/arch/arm/boot/dts/at91-kizboxmini.dts 
> > @@ -0,0 +1,130 @@ 
> > +/* 
> > + * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board 
> > + * 
> > + * Copyright (C) 2014 Gaël PORTAY <g.portay at overkiz.com> 
> > + * 
> > + * Licensed under GPLv2 or later. 
> > + */ 
> > +/dts-v1/; 
> > +#include "at91sam9g25.dtsi" 
> > +#include "at91sam9x5.dtsi" 
>
> Not needed as already included in at91sam9g25.dtsi: I remove it before 
> applying the patch. 
>
> Bye, 
>
> > +#include <dt-bindings/pwm/pwm.h> 
> > + 
> > +/ { 
> > + model = "Overkiz Kizbox mini"; 
> > + compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9"; 
> > + 
> > + chosen { 
> > + bootargs = "ubi.mtd=ubi"; 
> > + linux,stdout-path = &dbgu; 
> > + }; 
> > + 
> > + memory { 
> > + reg = <0x20000000 0x8000000>; 
> > + }; 
> > + 
> > + clocks { 
> > + slow_xtal { 
> > + clock-frequency = <32768>; 
> > + }; 
> > + 
> > + main_xtal { 
> > + clock-frequency = <12000000>; 
> > + }; 
> > + }; 
> > + 
> > + ahb { 
> > + apb { 
> > + usart0: serial at f801c000 { 
> > + status = "okay"; 
> > + }; 
> > + 
> > + macb0: ethernet at f802c000 { 
> > + phy-mode = "rmii"; 
> > + status = "okay"; 
> > + }; 
> > + 
> > + pwm0: pwm at f8034000 { 
> > + pinctrl-names = "default"; 
> > + pinctrl-0 = <&pinctrl_pwm0_pwm0_1 
> > +      &pinctrl_pwm0_pwm1_1>; 
> > + status = "okay"; 
> > + }; 
> > + 
> > + dbgu: serial at fffff200 { 
> > + status = "okay"; 
> > + }; 
> > + 
> > + watchdog at fffffe40 { 
> > + status = "okay"; 
> > + }; 
> > + }; 
> > + 
> > + usb0: ohci at 00600000 { 
> > + num-ports = <1>; 
> > + status = "okay"; 
> > + }; 
> > + 
> > + usb1: ehci at 00700000 { 
> > + status = "okay"; 
> > + }; 
> > + 
> > + nand0: nand at 40000000 { 
> > + nand-bus-width = <8>; 
> > + nand-ecc-mode = "hw"; 
> > + atmel,has-pmecc; 
> > + atmel,pmecc-cap = <4>; 
> > + atmel,pmecc-sector-size = <512>; 
> > + nand-on-flash-bbt; 
> > + status = "okay"; 
> > + 
> > + bootstrap at 0 { 
> > + label = "bootstrap"; 
> > + reg = <0x0 0x20000>; 
> > + }; 
> > + 
> > + ubi at 20000 { 
> > + label = "ubi"; 
> > + reg = <0x20000 0x7fe0000>; 
> > + }; 
> > + }; 
> > + }; 
> > + 
> > + gpio_keys { 
> > + compatible = "gpio-keys"; 
> > + #address-cells = <1>; 
> > + #size-cells = <0>; 
> > + 
> > + prog { 
> > + label = "PB_PROG"; 
> > + gpios = <&pioC 17 GPIO_ACTIVE_LOW>; 
> > + linux,code = <0x102>; 
> > + gpio-key,wakeup; 
> > + }; 
> > + 
> > + reset { 
> > + label = "PB_RST"; 
> > + gpios = <&pioC 16 GPIO_ACTIVE_LOW>; 
> > + linux,code = <0x100>; 
> > + gpio-key,wakeup; 
> > + }; 
> > + }; 
> > + 
> > + pwm_leds { 
> > + compatible = "pwm-leds"; 
> > + 
> > + green { 
> > + label = "pwm:green:user"; 
> > + pwms = <&pwm0 0 10000000 0>; 
> > + max-brightness = <255>; 
> > + linux,default-trigger = "default-on"; 
> > + }; 
> > + 
> > + red { 
> > + label = "pwm:red:user"; 
> > + pwms = <&pwm0 1 10000000 0>; 
> > + max-brightness = <255>; 
> > + linux,default-trigger = "default-on"; 
> > + }; 
> > + }; 
> > +}; 
> > 
>
>
> -- 
> Nicolas Ferre