[PATCH] arm, imx6, dts: add DT for aristainetos2 board

[Heiko Schocher]

Hello Sascha,

Am 07.05.2015 06:25, schrieb Sascha Hauer:
> On Wed, May 06, 2015 at 10:06:21AM +0200, Heiko Schocher wrote:
>> This patch add support for the imx6dl based aristainetos2 board
>> with following configuration:
>>
>> CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
>> MReset cause: POR
>> MBoard: aristaitenos2
>> DRAM:  1 GiB
>> NAND:  1024 MiB
>> MMC:   FSL_SDHC: 0, FSL_SDHC: 1
>> SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
>> Display: lb07wv8 (800x480)
>>
>> As this board can used with 2 different display types, the
>> differences between them are extracted into 2 DTS files, and
>> the common settings are collected in a common file.
>>
>> Signed-off-by: Heiko Schocher <hs at denx.de>
>> ---
>>
>>   arch/arm/boot/dts/imx6dl-aristainetos2_4.dts | 124 ++++++
>>   arch/arm/boot/dts/imx6dl-aristainetos2_7.dts |  63 +++
>>   arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi | 631 +++++++++++++++++++++++++++
>>   3 files changed, 818 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
>>   create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
>>   create mode 100644 arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
>>
>
> [...]
>
>> +
>> +&i2c1 {
>> +	clock-frequency = <100000>;
>
> I wonder why I see so many I2C nodes with this in this and other board
> dts files. Are all these buses so slow? Why not 400000? Also 100000 is
> the default anyway.

Good question... I remove the clock-frequency, as 100000 is the default.

>> +
>> +	gpio {
>> +		pinctrl_gpio: gpiogrp {
>> +			fsl,pins = <
>> +				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0 /* led enable */
>> +				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b0 /* backlight enable */
>> +				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x1b0b0 /* LCD power enable */
>> +				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0 /* led yellow */
>> +				MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0 /* led red */
>> +				MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b0b0 /* led green */
>> +				MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0 /* led blue */
>> +				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0 /* Profibus IRQ */
>> +				MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b0 /* FPGA IRQ */
>> +				MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x1b0b0 /* spi bus #2 SS driver enable */
>> +				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0 /* RST_LOC# PHY reset input (has pull-down!)*/
>> +				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b0b0 /* USB_OTG_ID = GPIO1_24*/
>> +				MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x1b0b0 /* SD2 level shifter output enable */
>> +				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x1b0b0 /* SD1 card detect input */
>> +				MX6QDL_PAD_DI0_PIN4__GPIO4_IO20		0x1b0b0 /* SD1 write protect input */
>> +				MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0 /* SD2 card detect input */
>> +				MX6QDL_PAD_SD4_DAT2__GPIO2_IO10		0x1b0b0 /* SD2 write protect input */
>
> Shouldn't the SD specific pins in the usdhc nodes below? Also backlight
> enable, LEDs could also be moved to the corresponding device nodes.

Yep, move them.

>> +				MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x1b0b0 /* Touchscreen IRQ */
>> +				MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b0b0 /* PCIe reset */
>> +			>;
>> +		};
>> +	};
>> +
>> +	gpmi-nand {
>> +		pinctrl_gpmi_nand: gpmi-nand {
>> +			fsl,pins = <
>> +				MX6QDL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
>> +				MX6QDL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
>> +				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
>> +				MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
>> +				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
>> +				MX6QDL_PAD_SD4_CMD__NAND_RE_B      0xb0b1
>> +				MX6QDL_PAD_SD4_CLK__NAND_WE_B      0xb0b1
>> +				MX6QDL_PAD_NANDF_D0__NAND_DATA00   0xb0b1
>> +				MX6QDL_PAD_NANDF_D1__NAND_DATA01   0xb0b1
>> +				MX6QDL_PAD_NANDF_D2__NAND_DATA02   0xb0b1
>> +				MX6QDL_PAD_NANDF_D3__NAND_DATA03   0xb0b1
>> +				MX6QDL_PAD_NANDF_D4__NAND_DATA04   0xb0b1
>> +				MX6QDL_PAD_NANDF_D5__NAND_DATA05   0xb0b1
>> +				MX6QDL_PAD_NANDF_D6__NAND_DATA06   0xb0b1
>> +				MX6QDL_PAD_NANDF_D7__NAND_DATA07   0xb0b1
>> +			>;
>> +		};
>> +	};
>> +
>> +	i2c1 {
>> +		pinctrl_i2c1: i2c1grp {
>> +			fsl,pins = <
>> +				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
>> +				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
>> +			>;
>> +		};
>> +	};
>> +
>> +	i2c2 {
>> +		pinctrl_i2c2: i2c2grp {
>> +			fsl,pins = <
>> +				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
>> +				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
>> +			>;
>> +		};
>> +	};
>> +
>> +	i2c3 {
>> +		pinctrl_i2c3: i2c3grp {
>> +			fsl,pins = <
>> +			MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
>> +			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>> +			>;
>
> Please check the indentation here and in some other pinctrl nodes.

Ups, rework this.

Thanks for the review.

bye,
Heiko
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany