[PATCH 1/2] dt-bindings: Add pxa1928 clock binding

[Rob Herring]

On Wed, May 6, 2015 at 2:17 AM, Stephen Boyd <sboyd at codeaurora.org> wrote:
> On 04/30, Rob Herring wrote:
>> diff --git a/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt
>> new file mode 100644
>> index 0000000..809c5a2
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt
>> @@ -0,0 +1,21 @@
>> +* Marvell PXA1928 Clock Controllers
>> +
>> +The PXA1928 clock subsystem generates and supplies clock to various
>> +controllers within the PXA1928 SoC. The PXA1928 contains 3 clock controller
>> +blocks called APMU, MPMU, and APBC roughly corresponding to internal buses.
>> +
>> +Required Properties:
>> +
>> +- compatible: should be one of the following.
>> +  - "marvell,pxa1928-apmu" - APMU controller compatible
>> +  - "marvell,pxa1928-mpmu" - MPMU controller compatible
>> +  - "marvell,pxa1928-apbc" - APBC controller compatible
>> +- reg: physical base address of the clock controller and length of memory mapped
>> +  region.
>> +- #clock-cells: should be 1.
>> +- #reset-cells: should be 1.
>> +
>> +Each clock is assigned an identifier and client nodes use the clock controller
>> +phandle and this identifier to specify the clock which they consume.
>> +
>> +All these identifiers can be found in <dt-bindings/clock/marvell,pxa1928.h>.
>
> No example?

There's nothing really special about this binding to show.

>> diff --git a/include/dt-bindings/clock/marvell,pxa1928.h b/include/dt-bindings/clock/marvell,pxa1928.h
>> new file mode 100644
>> index 0000000..c393ca2
>> --- /dev/null
>> +++ b/include/dt-bindings/clock/marvell,pxa1928.h
>> @@ -0,0 +1,57 @@
>> +#ifndef __DTS_MARVELL_PXA1928_CLOCK_H
>> +#define __DTS_MARVELL_PXA1928_CLOCK_H
>> +
>> +/*
>> + * Clock ID values here correspond to the control register offset/4.
>> + */
>> +
>> +/* apb periphrals */
>
> s/periphrals/peripherals/ ?

Uhh, cut-n-paste from marvell,mmp2.h...
>
>> +#define PXA1928_CLK_RTC                      0
>> +#define PXA1928_CLK_TWSI0            1
>> +#define PXA1928_CLK_TWSI1            2
>> +#define PXA1928_CLK_TWSI2            3
>> +#define PXA1928_CLK_TWSI3            4
>> +#define PXA1928_CLK_OWIRE            5
>> +#define PXA1928_CLK_KPC                      6
>> +#define PXA1928_CLK_TB_ROTARY                7
>> +#define PXA1928_CLK_SW_JTAG          8
>> +#define PXA1928_CLK_TIMER1           9
>
> This is really nitpicky, but I find the jump from decimal to hex odd.
> Is there any reason why we don't just use decimal or hex throughout?
> Perhaps it's related to why there are holes in the number space?

What is 9 in hex? ;) I'll prefix them. It's hard to convert decimal to
register values.

>> +#define PXA1928_CLK_UART0            0xb

Rob