[PATCH v4 2/2] serial/amba-pl011: Refactor and simplify TX FIFO handling
Dave Martin
Dave.Martin at arm.com
Fri Mar 27 07:59:31 PDT 2015
Commit 734745c serial/amba-pl011: Activate TX IRQ passively
adds some unnecessary complexity and overhead in the form of
a softirq mechanism for transmitting in the absence of interrupts.
After some discussion [1], this turns out to be unnecessary.
This patch simplifies the code flow to reduce the reliance on
subtle behaviour and avoid fragility under future maintenance.
To this end, the TX softirq mechanism is removed and instead
pl011_start_tx() will now simply stuff the FIFO until full
(guaranteeing future TX IRQs), or until there are no more chars
to write (in which case we don't care whether an IRQ happens).
[1] Thanks to Jakub Kiciński for his input and similar patch.
Signed-off-by: Dave Martin <Dave.Martin at arm.com>
---
drivers/tty/serial/amba-pl011.c | 119 +++++++++------------------------------
1 file changed, 26 insertions(+), 93 deletions(-)
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 6f5a072..f5bd842 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -58,7 +58,6 @@
#include <linux/pinctrl/consumer.h>
#include <linux/sizes.h>
#include <linux/io.h>
-#include <linux/workqueue.h>
#define UART_NR 14
@@ -157,9 +156,7 @@ struct uart_amba_port {
unsigned int lcrh_tx; /* vendor-specific */
unsigned int lcrh_rx; /* vendor-specific */
unsigned int old_cr; /* state during shutdown */
- struct delayed_work tx_softirq_work;
bool autorts;
- unsigned int tx_irq_seen; /* 0=none, 1=1, 2=2 or more */
char type[12];
#ifdef CONFIG_DMA_ENGINE
/* DMA stuff */
@@ -1172,15 +1169,14 @@ static void pl011_stop_tx(struct uart_port *port)
pl011_dma_tx_stop(uap);
}
-static bool pl011_tx_chars(struct uart_amba_port *uap);
+static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
/* Start TX with programmed I/O only (no DMA) */
static void pl011_start_tx_pio(struct uart_amba_port *uap)
{
uap->im |= UART011_TXIM;
writew(uap->im, uap->port.membase + UART011_IMSC);
- if (!uap->tx_irq_seen)
- pl011_tx_chars(uap);
+ pl011_tx_chars(uap, false);
}
static void pl011_start_tx(struct uart_port *port)
@@ -1247,87 +1243,54 @@ __acquires(&uap->port.lock)
spin_lock(&uap->port.lock);
}
-/*
- * Transmit a character
- * There must be at least one free entry in the TX FIFO to accept the char.
- *
- * Returns true if the FIFO might have space in it afterwards;
- * returns false if the FIFO definitely became full.
- */
-static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c)
+static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
+ bool from_irq)
{
+ if (unlikely(!from_irq) &&
+ readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
+ return false; /* unable to transmit character */
+
writew(c, uap->port.membase + UART01x_DR);
uap->port.icount.tx++;
- if (likely(uap->tx_irq_seen > 1))
- return true;
-
- return !(readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF);
+ return true;
}
-static bool pl011_tx_chars(struct uart_amba_port *uap)
+static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
{
struct circ_buf *xmit = &uap->port.state->xmit;
- int count;
-
- if (unlikely(uap->tx_irq_seen < 2))
- /*
- * Initial FIFO fill level unknown: we must check TXFF
- * after each write, so just try to fill up the FIFO.
- */
- count = uap->fifosize;
- else /* tx_irq_seen >= 2 */
- /*
- * FIFO initially at least half-empty, so we can simply
- * write half the FIFO without polling TXFF.
-
- * Note: the *first* TX IRQ can still race with
- * pl011_start_tx_pio(), which can result in the FIFO
- * being fuller than expected in that case.
- */
- count = uap->fifosize >> 1;
-
- /*
- * If the FIFO is full we're guaranteed a TX IRQ at some later point,
- * and can't transmit immediately in any case:
- */
- if (unlikely(uap->tx_irq_seen < 2 &&
- readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF))
- return false;
+ int count = uap->fifosize >> 1;
if (uap->port.x_char) {
- pl011_tx_char(uap, uap->port.x_char);
+ if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
+ return;
uap->port.x_char = 0;
--count;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
pl011_stop_tx(&uap->port);
- goto done;
+ return;
}
/* If we are using DMA mode, try to send some characters. */
if (pl011_dma_tx_irq(uap))
- goto done;
+ return;
- while (count-- > 0 && pl011_tx_char(uap, xmit->buf[xmit->tail])) {
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- if (uart_circ_empty(xmit))
+ do {
+ if (likely(from_irq) && count-- == 0)
break;
- }
+
+ if (!pl011_tx_char(uap, xmit->buf[xmit->tail], from_irq))
+ break;
+
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ } while (!uart_circ_empty(xmit));
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uap->port);
- if (uart_circ_empty(xmit)) {
+ if (uart_circ_empty(xmit))
pl011_stop_tx(&uap->port);
- goto done;
- }
-
- if (unlikely(!uap->tx_irq_seen))
- schedule_delayed_work(&uap->tx_softirq_work, uap->port.timeout);
-
-done:
- return false;
}
static void pl011_modem_status(struct uart_amba_port *uap)
@@ -1354,28 +1317,6 @@ static void pl011_modem_status(struct uart_amba_port *uap)
wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
}
-static void pl011_tx_softirq(struct work_struct *work)
-{
- struct delayed_work *dwork = to_delayed_work(work);
- struct uart_amba_port *uap =
- container_of(dwork, struct uart_amba_port, tx_softirq_work);
-
- spin_lock(&uap->port.lock);
- while (pl011_tx_chars(uap)) ;
- spin_unlock(&uap->port.lock);
-}
-
-static void pl011_tx_irq_seen(struct uart_amba_port *uap)
-{
- if (likely(uap->tx_irq_seen > 1))
- return;
-
- uap->tx_irq_seen++;
- if (uap->tx_irq_seen < 2)
- /* first TX IRQ */
- cancel_delayed_work(&uap->tx_softirq_work);
-}
-
static irqreturn_t pl011_int(int irq, void *dev_id)
{
struct uart_amba_port *uap = dev_id;
@@ -1414,10 +1355,8 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
if (status & (UART011_DSRMIS|UART011_DCDMIS|
UART011_CTSMIS|UART011_RIMIS))
pl011_modem_status(uap);
- if (status & UART011_TXIS) {
- pl011_tx_irq_seen(uap);
- pl011_tx_chars(uap);
- }
+ if (status & UART011_TXIS)
+ pl011_tx_chars(uap, true);
if (pass_counter-- == 0)
break;
@@ -1639,9 +1578,6 @@ static int pl011_startup(struct uart_port *port)
writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
- /* Assume that TX IRQ doesn't work until we see one: */
- uap->tx_irq_seen = 0;
-
spin_lock_irq(&uap->port.lock);
/* restore RTS and DTR */
@@ -1697,8 +1633,6 @@ static void pl011_shutdown(struct uart_port *port)
container_of(port, struct uart_amba_port, port);
unsigned int cr;
- cancel_delayed_work_sync(&uap->tx_softirq_work);
-
/*
* disable all interrupts
*/
@@ -2245,7 +2179,6 @@ static int pl011_probe(struct amba_device *dev, const struct amba_id *id)
uap->port.ops = &amba_pl011_pops;
uap->port.flags = UPF_BOOT_AUTOCONF;
uap->port.line = i;
- INIT_DELAYED_WORK(&uap->tx_softirq_work, pl011_tx_softirq);
/* Ensure interrupts from this UART are masked and cleared */
writew(0, uap->port.membase + UART011_IMSC);
--
1.7.10.4
More information about the linux-arm-kernel
mailing list