[RESEND PATCH v3 2/2] dma: Add Xilinx AXI Central Direct Memory Access Engine driver support
Appana Durga Kedareswara Rao
appana.durga.rao at xilinx.com
Fri Mar 27 04:25:52 PDT 2015
Ping !
> -----Original Message-----
> From: Kedareswara rao Appana [mailto:appana.durga.rao at xilinx.com]
> Sent: Wednesday, March 25, 2015 10:39 AM
> To: Michal Simek; Soren Brinkmann; vinod.koul at intel.com;
> dan.j.williams at intel.com
> Cc: appand at xilinx.com; dmaengine at vger.kernel.org; linux-arm-
> kernel at lists.infradead.org; linux-kernel at vger.kernel.org; Appana Durga
> Kedareswara Rao; Srikanth Thokala
> Subject: [RESEND PATCH v3 2/2] dma: Add Xilinx AXI Central Direct Memory
> Access Engine driver support
>
> This is the driver for the AXI Central Direct Memory Access (AXI
> CDMA) core, which is a soft Xilinx IP core that provides high-bandwidth Direct
> Memory Access (DMA) between a memory-mapped source address and a
> memory-mapped destination address.
>
> This module works on Zynq (ARM Based SoC) and Microblaze platforms.
>
> Signed-off-by: Srikanth Thokala <sthokal at xilinx.com>
> Signed-off-by: Kedareswara rao Appana <appanad at xilinx.com>
> ---
> This patch is rebased on top of dma: xilinx-dma: move header file to common
> location.
>
> Changes in v3:
> - Check for CDMA idle condition before changing the configuration.
> - Modified the xilinx_dma.h header file location to the
> include/linux/dma/xilinx_dma.h
> Changes in v2:
> - Rebased on 3.16-rc7.
>
> drivers/dma/Kconfig | 12 +
> drivers/dma/xilinx/Makefile | 1 +
> drivers/dma/xilinx/xilinx_cdma.c | 1000
> ++++++++++++++++++++++++++++++++++++++
> include/linux/dma/xilinx_dma.h | 15 +-
> 4 files changed, 1027 insertions(+), 1 deletion(-) create mode 100644
> drivers/dma/xilinx/xilinx_cdma.c
>
> diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig index
> a874b6e..1bc17c6 100644
> --- a/drivers/dma/Kconfig
> +++ b/drivers/dma/Kconfig
> @@ -425,6 +425,18 @@ config IMG_MDC_DMA
> help
> Enable support for the IMG multi-threaded DMA controller (MDC).
>
> +config XILINX_CDMA
> + tristate "Xilinx AXI CDMA Engine"
> + depends on (ARCH_ZYNQ || MICROBLAZE)
> + select DMA_ENGINE
> + help
> + Enable support for Xilinx AXI CDMA Soft IP.
> +
> + The AXI CDMA is a soft IP which provides high-bandwidth
> + Direct Memory Access (DMA) between a memory-mapped source
> + address and a memory-mapped destination address using the
> + AXI4 protocol.
> +
> config DMA_ENGINE
> bool
>
> diff --git a/drivers/dma/xilinx/Makefile b/drivers/dma/xilinx/Makefile index
> 3c4e9f2..e1dee77 100644
> --- a/drivers/dma/xilinx/Makefile
> +++ b/drivers/dma/xilinx/Makefile
> @@ -1 +1,2 @@
> obj-$(CONFIG_XILINX_VDMA) += xilinx_vdma.o
> +obj-$(CONFIG_XILINX_CDMA) += xilinx_cdma.o
> diff --git a/drivers/dma/xilinx/xilinx_cdma.c
> b/drivers/dma/xilinx/xilinx_cdma.c
> new file mode 100644
> index 0000000..ff82fab
> --- /dev/null
> +++ b/drivers/dma/xilinx/xilinx_cdma.c
> @@ -0,0 +1,1000 @@
> +/*
> + * DMA driver for Xilinx Central DMA Engine
> + *
> + * Copyright (C) 2010 - 2015 Xilinx, Inc. All rights reserved.
> + *
> + * Based on the Freescale DMA driver.
> + *
> + * Description:
> + * The AXI CDMA, is a soft IP, which provides high-bandwidth Direct
> +Memory
> + * Access (DMA) between a memory-mapped source address and a
> +memory-mapped
> + * destination address.
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation, either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/dmapool.h>
> +#include <linux/dma/xilinx_dma.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_dma.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <linux/slab.h>
> +
> +#include "../dmaengine.h"
> +
> +/* Register Offsets */
> +#define XILINX_CDMA_CONTROL_OFFSET 0x00
> +#define XILINX_CDMA_STATUS_OFFSET 0x04
> +#define XILINX_CDMA_CDESC_OFFSET 0x08
> +#define XILINX_CDMA_TDESC_OFFSET 0x10
> +#define XILINX_CDMA_SRCADDR_OFFSET 0x18
> +#define XILINX_CDMA_DSTADDR_OFFSET 0x20
> +#define XILINX_CDMA_BTT_OFFSET 0x28
> +
> +/* General register bits definitions */
> +#define XILINX_CDMA_CR_RESET BIT(2)
> +#define XILINX_CDMA_CR_SGMODE BIT(3)
> +
> +#define XILINX_CDMA_SR_IDLE BIT(1)
> +
> +#define XILINX_CDMA_XR_IRQ_IOC_MASK BIT(12)
> +#define XILINX_CDMA_XR_IRQ_DELAY_MASK BIT(13) #define
> +XILINX_CDMA_XR_IRQ_ERROR_MASK BIT(14)
> +#define XILINX_CDMA_XR_IRQ_ALL_MASK GENMASK(14, 12)
> +
> +#define XILINX_CDMA_XR_DELAY_MASK GENMASK(31, 24)
> +#define XILINX_CDMA_XR_COALESCE_MASK GENMASK(23, 16)
> +
> +#define XILINX_CDMA_DELAY_MAX GENMASK(7, 0)
> +#define XILINX_CDMA_DELAY_SHIFT 24
> +
> +#define XILINX_CDMA_COALESCE_MAX GENMASK(7, 0)
> +#define XILINX_CDMA_COALESCE_SHIFT 16
> +
> +/* Delay loop counter to prevent hardware failure */
> +#define XILINX_CDMA_RESET_LOOP 1000000
> +
> +/* Maximum transfer length */
> +#define XILINX_CDMA_MAX_TRANS_LEN GENMASK(22, 0)
> +
> +/**
> + * struct xilinx_cdma_desc_hw - Hardware Descriptor
> + * @next_desc: Next Descriptor Pointer @0x00
> + * @pad1: Reserved @0x04
> + * @src_addr: Source address @0x08
> + * @pad2: Reserved @0x0C
> + * @dest_addr: Destination address @0x10
> + * @pad3: Reserved @0x14
> + * @control: Control field @0x18
> + * @status: Status field @0x1C
> + */
> +struct xilinx_cdma_desc_hw {
> + u32 next_desc;
> + u32 pad1;
> + u32 src_addr;
> + u32 pad2;
> + u32 dest_addr;
> + u32 pad3;
> + u32 control;
> + u32 status;
> +} __aligned(64);
> +
> +/**
> + * struct xilinx_cdma_tx_segment - Descriptor segment
> + * @hw: Hardware descriptor
> + * @node: Node in the descriptor segments list
> + * @phys: Physical address of segment
> + */
> +struct xilinx_cdma_tx_segment {
> + struct xilinx_cdma_desc_hw hw;
> + struct list_head node;
> + dma_addr_t phys;
> +} __aligned(64);
> +
> +/**
> + * struct xilinx_cdma_tx_descriptor - Per Transaction structure
> + * @async_tx: Async transaction descriptor
> + * @segments: TX segments list
> + * @node: Node in the channel descriptors list */ struct
> +xilinx_cdma_tx_descriptor {
> + struct dma_async_tx_descriptor async_tx;
> + struct list_head segments;
> + struct list_head node;
> +};
> +
> +/**
> + * struct xilinx_cdma_chan - Driver specific cdma channel structure
> + * @xdev: Driver specific device structure
> + * @lock: Descriptor operation lock
> + * @done_list: Complete descriptors
> + * @pending_list: Descriptors waiting
> + * @active_desc: Active descriptor
> + * @allocated_desc: Allocated descriptor
> + * @common: DMA common channel
> + * @desc_pool: Descriptors pool
> + * @dev: The dma device
> + * @irq: Channel IRQ
> + * @has_sg: Support scatter transfers
> + * @err: Channel has errors
> + * @tasklet: Cleanup work after irq
> + */
> +struct xilinx_cdma_chan {
> + struct xilinx_cdma_device *xdev;
> + spinlock_t lock;
> + struct list_head done_list;
> + struct list_head pending_list;
> + struct xilinx_cdma_tx_descriptor *active_desc;
> + struct xilinx_cdma_tx_descriptor *allocated_desc;
> + struct dma_chan common;
> + struct dma_pool *desc_pool;
> + struct device *dev;
> + int irq;
> + bool has_sg;
> + int err;
> + struct tasklet_struct tasklet;
> +};
> +
> +/**
> + * struct xilinx_cdma_device - CDMA device structure
> + * @regs: I/O mapped base address
> + * @dev: Device Structure
> + * @common: DMA device structure
> + * @chan: Driver specific cdma channel
> + * @has_sg: Specifies whether Scatter-Gather is present or not */
> +struct xilinx_cdma_device {
> + void __iomem *regs;
> + struct device *dev;
> + struct dma_device common;
> + struct xilinx_cdma_chan *chan;
> + bool has_sg;
> +};
> +
> +/* Macros */
> +#define to_xilinx_chan(chan) \
> + container_of(chan, struct xilinx_cdma_chan, common) #define
> +to_cdma_tx_descriptor(tx) \
> + container_of(tx, struct xilinx_cdma_tx_descriptor, async_tx)
> +
> +/* IO accessors */
> +static inline void cdma_write(struct xilinx_cdma_chan *chan, u32 reg,
> +u32 val) {
> + writel(val, chan->xdev->regs + reg);
> +}
> +
> +static inline u32 cdma_read(struct xilinx_cdma_chan *chan, u32 reg) {
> + return readl(chan->xdev->regs + reg);
> +}
> +
> +static inline void cdma_ctrl_clr(struct xilinx_cdma_chan *chan, u32 reg,
> + u32 clr)
> +{
> + cdma_write(chan, reg, cdma_read(chan, reg) & ~clr); }
> +
> +static inline void cdma_ctrl_set(struct xilinx_cdma_chan *chan, u32 reg,
> + u32 set)
> +{
> + cdma_write(chan, reg, cdma_read(chan, reg) | set); }
> +
> +/*
> +-----------------------------------------------------------------------
> +------
> + * Descriptors and segments alloc and free */
> +
> +/**
> + * xilinx_cdma_alloc_tx_segment - Allocate transaction segment
> + * @chan: Driver specific cdma channel
> + *
> + * Return: The allocated segment on success and NULL on failure.
> + */
> +static struct xilinx_cdma_tx_segment *
> +xilinx_cdma_alloc_tx_segment(struct xilinx_cdma_chan *chan) {
> + struct xilinx_cdma_tx_segment *segment;
> + dma_addr_t phys;
> +
> + segment = dma_pool_alloc(chan->desc_pool, GFP_ATOMIC, &phys);
> + if (!segment)
> + return NULL;
> +
> + memset(segment, 0, sizeof(*segment));
> + segment->phys = phys;
> +
> + return segment;
> +}
> +
> +/**
> + * xilinx_cdma_free_tx_segment - Free transaction segment
> + * @chan: Driver specific cdma channel
> + * @segment: cdma transaction segment
> + */
> +static void xilinx_cdma_free_tx_segment(struct xilinx_cdma_chan *chan,
> + struct xilinx_cdma_tx_segment
> *segment) {
> + dma_pool_free(chan->desc_pool, segment, segment->phys); }
> +
> +/**
> + * xilinx_cdma_tx_descriptor - Allocate transaction descriptor
> + * @chan: Driver specific cdma channel
> + *
> + * Return: The allocated descriptor on success and NULL on failure.
> + */
> +static struct xilinx_cdma_tx_descriptor *
> +xilinx_cdma_alloc_tx_descriptor(struct xilinx_cdma_chan *chan) {
> + struct xilinx_cdma_tx_descriptor *desc;
> + unsigned long flags;
> +
> + if (chan->allocated_desc)
> + return chan->allocated_desc;
> +
> + desc = kzalloc(sizeof(*desc), GFP_KERNEL);
> + if (!desc)
> + return NULL;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> + chan->allocated_desc = desc;
> + spin_unlock_irqrestore(&chan->lock, flags);
> +
> + INIT_LIST_HEAD(&desc->segments);
> +
> + return desc;
> +}
> +
> +/**
> + * xilinx_cdma_free_tx_descriptor - Free transaction descriptor
> + * @chan: Driver specific cdma channel
> + * @desc: cdma transaction descriptor
> + */
> +static void
> +xilinx_cdma_free_tx_descriptor(struct xilinx_cdma_chan *chan,
> + struct xilinx_cdma_tx_descriptor *desc) {
> + struct xilinx_cdma_tx_segment *segment, *next;
> +
> + if (!desc)
> + return;
> +
> + list_for_each_entry_safe(segment, next, &desc->segments, node) {
> + list_del(&segment->node);
> + xilinx_cdma_free_tx_segment(chan, segment);
> + }
> +
> + kfree(desc);
> +}
> +
> +/**
> + * xilinx_cdma_alloc_chan_resources - Allocate channel resources
> + * @dchan: DMA channel
> + *
> + * Return: '0' on success and failure value on error */ static int
> +xilinx_cdma_alloc_chan_resources(struct dma_chan *dchan) {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> +
> + /* Has this channel already been allocated? */
> + if (chan->desc_pool)
> + return 0;
> +
> + /*
> + * We need the descriptor to be aligned to 64bytes
> + * for meeting Xilinx DMA specification requirement.
> + */
> + chan->desc_pool = dma_pool_create("xilinx_cdma_desc_pool",
> + chan->dev,
> + sizeof(struct xilinx_cdma_tx_segment),
> + __alignof__(struct
> xilinx_cdma_tx_segment), 0);
> + if (!chan->desc_pool) {
> + dev_err(chan->dev,
> + "unable to allocate channel descriptor pool\n");
> + return -ENOMEM;
> + }
> +
> + dma_cookie_init(dchan);
> + return 0;
> +}
> +
> +/**
> + * xilinx_cdma_free_desc_list - Free descriptors list
> + * @chan: Driver specific cdma channel
> + * @list: List to parse and delete the descriptor */ static void
> +xilinx_cdma_free_desc_list(struct xilinx_cdma_chan *chan,
> + struct list_head *list)
> +{
> + struct xilinx_cdma_tx_descriptor *desc, *next;
> +
> + list_for_each_entry_safe(desc, next, list, node) {
> + list_del(&desc->node);
> + xilinx_cdma_free_tx_descriptor(chan, desc);
> + }
> +}
> +
> +/**
> + * xilinx_cdma_free_chan_resources - Free channel resources
> + * @dchan: DMA channel
> + */
> +static void xilinx_cdma_free_chan_resources(struct dma_chan *dchan) {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> + unsigned long flags;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> + xilinx_cdma_free_desc_list(chan, &chan->done_list);
> + xilinx_cdma_free_desc_list(chan, &chan->pending_list);
> + spin_unlock_irqrestore(&chan->lock, flags);
> +
> + dma_pool_destroy(chan->desc_pool);
> + chan->desc_pool = NULL;
> +}
> +
> +/**
> + * xilinx_cdma_chan_desc_cleanup - Clean channel descriptors
> + * @chan: Driver specific cdma channel
> + */
> +static void xilinx_cdma_chan_desc_cleanup(struct xilinx_cdma_chan
> +*chan) {
> + struct xilinx_cdma_tx_descriptor *desc, *next;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> +
> + list_for_each_entry_safe(desc, next, &chan->done_list, node) {
> + dma_async_tx_callback callback;
> + void *callback_param;
> +
> + /* Remove from the list of running transactions */
> + list_del(&desc->node);
> +
> + /* Run the link descriptor callback function */
> + callback = desc->async_tx.callback;
> + callback_param = desc->async_tx.callback_param;
> + if (callback) {
> + spin_unlock_irqrestore(&chan->lock, flags);
> + callback(callback_param);
> + spin_lock_irqsave(&chan->lock, flags);
> + }
> +
> + /* Run any dependencies, then free the descriptor */
> + dma_run_dependencies(&desc->async_tx);
> + xilinx_cdma_free_tx_descriptor(chan, desc);
> + }
> +
> + spin_unlock_irqrestore(&chan->lock, flags); }
> +
> +/**
> + * xilinx_cdma_tx_status - Get CDMA transaction status
> + * @dchan: DMA channel
> + * @cookie: Transaction identifier
> + * @txstate: Transaction state
> + *
> + * Return: DMA transaction status
> + */
> +static enum dma_status xilinx_tx_status(struct dma_chan *dchan,
> + dma_cookie_t cookie,
> + struct dma_tx_state *txstate)
> +{
> + return dma_cookie_status(dchan, cookie, txstate); }
> +
> +/**
> + * xilinx_cdma_is_idle - Check if cdma channel is idle
> + * @chan: Driver specific cdma channel
> + *
> + * Return: 'true' if idle, 'false' if not.
> + */
> +static bool cdma_is_idle(struct xilinx_cdma_chan *chan) {
> + return cdma_read(chan, XILINX_CDMA_STATUS_OFFSET) &
> +XILINX_CDMA_SR_IDLE; }
> +
> +/**
> + * xilinx_cdma_start_transfer - Starts cdma transfer
> + * @chan: Driver specific channel struct pointer */ static void
> +xilinx_cdma_start_transfer(struct xilinx_cdma_chan *chan) {
> + unsigned long flags;
> + struct xilinx_cdma_tx_descriptor *desc;
> + struct xilinx_cdma_tx_segment *head, *tail;
> +
> + if (chan->err)
> + return;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> +
> + if (list_empty(&chan->pending_list))
> + goto out_unlock;
> +
> + /* If hardware is busy, cannot submit */
> + if (!cdma_is_idle(chan)) {
> + dev_dbg(chan->dev, "DMA controller still busy %x\n",
> + cdma_read(chan, XILINX_CDMA_STATUS_OFFSET));
> + goto out_unlock;
> + }
> +
> + desc = list_first_entry(&chan->pending_list,
> + struct xilinx_cdma_tx_descriptor, node);
> +
> + if (chan->has_sg) {
> + head = list_first_entry(&desc->segments,
> + struct xilinx_cdma_tx_segment,
> node);
> + tail = list_entry(desc->segments.prev,
> + struct xilinx_cdma_tx_segment, node);
> +
> + cdma_write(chan, XILINX_CDMA_CDESC_OFFSET, head-
> >phys);
> +
> + /* Update tail ptr register which will start the transfer */
> + cdma_write(chan, XILINX_CDMA_TDESC_OFFSET, tail-
> >phys);
> + } else {
> + /* In simple mode */
> + struct xilinx_cdma_tx_segment *segment;
> + struct xilinx_cdma_desc_hw *hw;
> +
> + segment = list_first_entry(&desc->segments,
> + struct xilinx_cdma_tx_segment,
> + node);
> +
> + hw = &segment->hw;
> +
> + cdma_write(chan, XILINX_CDMA_SRCADDR_OFFSET, hw-
> >src_addr);
> + cdma_write(chan, XILINX_CDMA_DSTADDR_OFFSET, hw-
> >dest_addr);
> +
> + /* Start the transfer */
> + cdma_write(chan, XILINX_CDMA_BTT_OFFSET,
> + hw->control &
> XILINX_CDMA_MAX_TRANS_LEN);
> + }
> +
> + list_del(&desc->node);
> + chan->active_desc = desc;
> +
> +out_unlock:
> + spin_unlock_irqrestore(&chan->lock, flags); }
> +
> +/**
> + * xilinx_cdma_issue_pending - Issue pending transactions
> + * @dchan: DMA channel
> + */
> +static void xilinx_cdma_issue_pending(struct dma_chan *dchan) {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> +
> + xilinx_cdma_start_transfer(chan);
> +}
> +
> +/**
> + * xilinx_cdma_complete_descriptor - Mark the active descriptor as
> +complete
> + * @chan : xilinx DMA channel
> + */
> +static void xilinx_cdma_complete_descriptor(struct xilinx_cdma_chan
> +*chan) {
> + struct xilinx_cdma_tx_descriptor *desc;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> +
> + desc = chan->active_desc;
> + if (!desc) {
> + dev_dbg(chan->dev, "no running descriptors\n");
> + goto out_unlock;
> + }
> +
> + dma_cookie_complete(&desc->async_tx);
> + list_add_tail(&desc->node, &chan->done_list);
> +
> + chan->active_desc = NULL;
> +
> +out_unlock:
> + spin_unlock_irqrestore(&chan->lock, flags); }
> +
> +/**
> + * xilinx_cdma_chan_reset - Reset CDMA channel
> + * @chan: Driver specific CDMA channel
> + *
> + * Return: '0' on success and failure value on error */ static int
> +xilinx_cdma_chan_reset(struct xilinx_cdma_chan *chan) {
> + int loop = XILINX_CDMA_RESET_LOOP;
> + u32 tmp;
> +
> + cdma_ctrl_set(chan, XILINX_CDMA_CONTROL_OFFSET,
> + XILINX_CDMA_CR_RESET);
> +
> + tmp = cdma_read(chan, XILINX_CDMA_CONTROL_OFFSET) &
> + XILINX_CDMA_CR_RESET;
> +
> + /* Wait for the hardware to finish reset */
> + do {
> + tmp = cdma_read(chan, XILINX_CDMA_CONTROL_OFFSET) &
> + XILINX_CDMA_CR_RESET;
> + } while (loop-- && tmp);
> +
> + if (!loop) {
> + dev_err(chan->dev, "reset timeout, cr %x, sr %x\n",
> + cdma_read(chan, XILINX_CDMA_CONTROL_OFFSET),
> + cdma_read(chan, XILINX_CDMA_STATUS_OFFSET));
> + return -EBUSY;
> + }
> +
> + /* Enable interrupts */
> + cdma_ctrl_set(chan, XILINX_CDMA_CONTROL_OFFSET,
> + XILINX_CDMA_XR_IRQ_ALL_MASK);
> +
> + /* Enable SG Mode */
> + if (chan->has_sg)
> + cdma_ctrl_set(chan, XILINX_CDMA_CONTROL_OFFSET,
> + XILINX_CDMA_CR_SGMODE);
> + return 0;
> +}
> +
> +/**
> + * xilinx_cdma_irq_handler - CDMA Interrupt handler
> + * @irq: IRQ number
> + * @data: Pointer to the Xilinx CDMA channel structure
> + *
> + * Return: IRQ_HANDLED/IRQ_NONE
> + */
> +static irqreturn_t xilinx_cdma_irq_handler(int irq, void *data) {
> + struct xilinx_cdma_chan *chan = data;
> + u32 status;
> +
> + status = cdma_read(chan, XILINX_CDMA_STATUS_OFFSET);
> + if (!(status & XILINX_CDMA_XR_IRQ_ALL_MASK))
> + return IRQ_NONE;
> +
> + /* Ack the interrupts */
> + cdma_write(chan, XILINX_CDMA_STATUS_OFFSET,
> + XILINX_CDMA_XR_IRQ_ALL_MASK);
> +
> + if (status & XILINX_CDMA_XR_IRQ_ERROR_MASK) {
> + dev_err(chan->dev,
> + "Channel %x has errors %x, cdr %x tdr %x\n",
> + (u32)chan,
> + (u32)cdma_read(chan,
> XILINX_CDMA_STATUS_OFFSET),
> + (u32)cdma_read(chan,
> XILINX_CDMA_CDESC_OFFSET),
> + (u32)cdma_read(chan,
> XILINX_CDMA_TDESC_OFFSET));
> + chan->err = true;
> + }
> +
> + /*
> + * Device takes too long to do the transfer when user requires
> + * responsiveness
> + */
> + if (status & XILINX_CDMA_XR_IRQ_DELAY_MASK)
> + dev_dbg(chan->dev, "Inter-packet latency too long\n");
> +
> + if (status & XILINX_CDMA_XR_IRQ_IOC_MASK) {
> + xilinx_cdma_complete_descriptor(chan);
> + xilinx_cdma_start_transfer(chan);
> + }
> +
> + tasklet_schedule(&chan->tasklet);
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * xilinx_cdma_do_tasklet - Schedule completion tasklet
> + * @data: Pointer to the Xilinx cdma channel structure */ static void
> +xilinx_cdma_do_tasklet(unsigned long data) {
> + struct xilinx_cdma_chan *chan = (struct xilinx_cdma_chan *)data;
> +
> + xilinx_cdma_chan_desc_cleanup(chan);
> +}
> +
> +/**
> + * xilinx_cdma_tx_submit - Submit DMA transaction
> + * @tx: Async transaction descriptor
> + *
> + * Return: cookie value on success and failure value on error */
> +static dma_cookie_t xilinx_cdma_tx_submit(struct
> +dma_async_tx_descriptor *tx) {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(tx->chan);
> + struct xilinx_cdma_tx_descriptor *desc =
> to_cdma_tx_descriptor(tx);
> + dma_cookie_t cookie;
> + unsigned long flags;
> + int err;
> +
> + if (chan->err) {
> + /*
> + * If reset fails, need to hard reset the system.
> + * Channel is no longer functional
> + */
> + err = xilinx_cdma_chan_reset(chan);
> + if (err < 0)
> + return err;
> + }
> +
> + spin_lock_irqsave(&chan->lock, flags);
> +
> + cookie = dma_cookie_assign(tx);
> +
> + /* Append the transaction to the pending transactions queue. */
> + list_add_tail(&desc->node, &chan->pending_list);
> +
> + /* Free the allocated desc */
> + chan->allocated_desc = NULL;
> +
> + spin_unlock_irqrestore(&chan->lock, flags);
> +
> + return cookie;
> +}
> +
> +/**
> + * xilinx_cdma_prep_memcpy - prepare descriptors for a memcpy
> +transaction
> + * @dchan: DMA channel
> + * @dma_dst: destination address
> + * @dma_src: source address
> + * @len: transfer length
> + * @flags: transfer ack flags
> + *
> + * Return: Async transaction descriptor on success and NULL on failure
> +*/ static struct dma_async_tx_descriptor *
> +xilinx_cdma_prep_memcpy(struct dma_chan *dchan, dma_addr_t
> dma_dst,
> + dma_addr_t dma_src, size_t len, unsigned long flags)
> {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> + struct xilinx_cdma_desc_hw *hw;
> + struct xilinx_cdma_tx_descriptor *desc;
> + struct xilinx_cdma_tx_segment *segment, *prev;
> +
> + if (!len || len > XILINX_CDMA_MAX_TRANS_LEN)
> + return NULL;
> +
> + desc = xilinx_cdma_alloc_tx_descriptor(chan);
> + if (!desc)
> + return NULL;
> +
> + dma_async_tx_descriptor_init(&desc->async_tx, &chan->common);
> + desc->async_tx.tx_submit = xilinx_cdma_tx_submit;
> + async_tx_ack(&desc->async_tx);
> +
> + /* Allocate the link descriptor from DMA pool */
> + segment = xilinx_cdma_alloc_tx_segment(chan);
> + if (!segment)
> + goto error;
> +
> + hw = &segment->hw;
> + hw->control = len;
> + hw->src_addr = dma_src;
> + hw->dest_addr = dma_dst;
> +
> + /* Fill the previous next descriptor with current */
> + prev = list_last_entry(&desc->segments,
> + struct xilinx_cdma_tx_segment, node);
> + prev->hw.next_desc = segment->phys;
> +
> + /* Insert the segment into the descriptor segments list. */
> + list_add_tail(&segment->node, &desc->segments);
> +
> + prev = segment;
> +
> + /* Link the last hardware descriptor with the first. */
> + segment = list_first_entry(&desc->segments,
> + struct xilinx_cdma_tx_segment, node);
> + prev->hw.next_desc = segment->phys;
> +
> + return &desc->async_tx;
> +
> +error:
> + xilinx_cdma_free_tx_descriptor(chan, desc);
> + return NULL;
> +}
> +
> +/**
> + * xilinx_cdma_device_control - Configure DMA channel of the device
> + * @dchan: DMA Channel pointer
> + * @cmd: DMA control command
> + * @arg: Channel configuration
> + *
> + * Return: '0' on success and failure value on error */ static int
> +xilinx_cdma_device_control(struct dma_chan *dchan,
> + enum dma_ctrl_cmd cmd, unsigned long arg)
> {
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> + unsigned long flags;
> +
> + if (cmd != DMA_TERMINATE_ALL)
> + return -ENXIO;
> +
> + spin_lock_irqsave(&chan->lock, flags);
> +
> + /* Remove and free all of the descriptors in the lists */
> + xilinx_cdma_free_desc_list(chan, &chan->pending_list);
> + xilinx_cdma_free_desc_list(chan, &chan->done_list);
> +
> + spin_unlock_irqrestore(&chan->lock, flags);
> +
> + return 0;
> +}
> +
> +/**
> + * xilinx_cdma_channel_set_config - Configure cdma channel
> + * @dchan: DMA channel
> + * @cfg: cdma device configuration pointer
> + *
> + * Return: '0' on success and failure value on error */ int
> +xilinx_cdma_channel_set_config(struct dma_chan *dchan,
> + struct xilinx_cdma_config *cfg)
> +{
> + struct xilinx_cdma_chan *chan = to_xilinx_chan(dchan);
> + u32 reg = cdma_read(chan, XILINX_CDMA_CONTROL_OFFSET);
> +
> + if (!cdma_is_idle(chan))
> + return -EBUSY;
> +
> + if (cfg->reset)
> + return xilinx_cdma_chan_reset(chan);
> +
> + if (cfg->coalesc <= XILINX_CDMA_COALESCE_MAX) {
> + reg &= ~XILINX_CDMA_XR_COALESCE_MASK;
> + reg |= cfg->coalesc << XILINX_CDMA_COALESCE_SHIFT;
> + }
> +
> + if (cfg->delay <= XILINX_CDMA_DELAY_MAX) {
> + reg &= ~XILINX_CDMA_XR_DELAY_MASK;
> + reg |= cfg->delay << XILINX_CDMA_DELAY_SHIFT;
> + }
> +
> + cdma_write(chan, XILINX_CDMA_CONTROL_OFFSET, reg);
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(xilinx_cdma_channel_set_config);
> +
> +/*
> +-----------------------------------------------------------------------
> +------
> + * Probe and remove
> + */
> +
> +/**
> + * xilinx_cdma_free_channel - Channel remove function
> + * @chan: Driver specific cdma channel
> + */
> +static void xilinx_cdma_free_channel(struct xilinx_cdma_chan *chan) {
> + /* Disable Interrupts */
> + cdma_ctrl_clr(chan, XILINX_CDMA_CONTROL_OFFSET,
> + XILINX_CDMA_XR_IRQ_ALL_MASK);
> +
> + if (chan->irq > 0)
> + free_irq(chan->irq, chan);
> +
> + tasklet_kill(&chan->tasklet);
> +
> + list_del(&chan->common.device_node);
> +}
> +
> +/**
> + * xilinx_cdma_chan_probe - Per Channel Probing
> + * It get channel features from the device tree entry and
> + * initialize special channel handling routines
> + *
> + * @xdev: Driver specific device structure
> + * @node: Device node
> + *
> + * Return: '0' on success and failure value on error */ static int
> +xilinx_cdma_chan_probe(struct xilinx_cdma_device *xdev,
> + struct device_node *node)
> +{
> + struct xilinx_cdma_chan *chan;
> + bool has_dre;
> + u32 value, width;
> + int err;
> +
> + /* Alloc channel */
> + chan = devm_kzalloc(xdev->dev, sizeof(*chan), GFP_KERNEL);
> + if (!chan)
> + return -ENOMEM;
> +
> + chan->dev = xdev->dev;
> + chan->has_sg = xdev->has_sg;
> + chan->xdev = xdev;
> +
> + spin_lock_init(&chan->lock);
> + INIT_LIST_HEAD(&chan->pending_list);
> + INIT_LIST_HEAD(&chan->done_list);
> +
> + /* Retrieve the channel properties from the device tree */
> + has_dre = of_property_read_bool(node, "xlnx,include-dre");
> +
> + err = of_property_read_u32(node, "xlnx,datawidth", &value);
> + if (err) {
> + dev_err(xdev->dev, "unable to read datawidth property");
> + return err;
> + }
> + width = value >> 3; /* convert bits to bytes */
> +
> + /* If data width is greater than 8 bytes, DRE is not in hw */
> + if (width > 8)
> + has_dre = false;
> +
> + if (!has_dre)
> + xdev->common.copy_align = fls(width - 1);
> +
> + /* Request the interrupt */
> + chan->irq = irq_of_parse_and_map(node, 0);
> + err = request_irq(chan->irq, xilinx_cdma_irq_handler, IRQF_SHARED,
> + "xilinx-cdma-controller", chan);
> + if (err) {
> + dev_err(xdev->dev, "unable to request IRQ %d\n", chan-
> >irq);
> + return err;
> + }
> +
> + /* Initialize the tasklet */
> + tasklet_init(&chan->tasklet, xilinx_cdma_do_tasklet,
> + (unsigned long)chan);
> +
> + /*
> + * Initialize the DMA channel and add it to the DMA engine channels
> + * list.
> + */
> + chan->common.device = &xdev->common;
> +
> + list_add_tail(&chan->common.device_node, &xdev-
> >common.channels);
> + xdev->chan = chan;
> +
> + /* Initialize the channel */
> + err = xilinx_cdma_chan_reset(chan);
> + if (err) {
> + dev_err(xdev->dev, "Reset channel failed\n");
> + return err;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * of_dma_xilinx_xlate - Translation function
> + * @dma_spec: Pointer to DMA specifier as found in the device tree
> + * @ofdma: Pointer to DMA controller data
> + *
> + * Return: DMA channel pointer on success and NULL on error */ static
> +struct dma_chan *of_dma_xilinx_xlate(struct of_phandle_args
> *dma_spec,
> + struct of_dma *ofdma)
> +{
> + struct xilinx_cdma_device *xdev = ofdma->of_dma_data;
> +
> + return dma_get_slave_channel(&xdev->chan->common);
> +}
> +
> +/**
> + * xilinx_cdma_probe - Driver probe function
> + * @pdev: Pointer to the platform_device structure
> + *
> + * Return: '0' on success and failure value on error */ static int
> +xilinx_cdma_probe(struct platform_device *pdev) {
> + struct xilinx_cdma_device *xdev;
> + struct device_node *child, *node;
> + struct resource *res;
> + int ret;
> +
> + xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL);
> + if (!xdev)
> + return -ENOMEM;
> +
> + xdev->dev = &(pdev->dev);
> + INIT_LIST_HEAD(&xdev->common.channels);
> +
> + node = pdev->dev.of_node;
> +
> + /* Map the registers */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + xdev->regs = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(xdev->regs))
> + return PTR_ERR(xdev->regs);
> +
> + /* Check if SG is enabled */
> + xdev->has_sg = of_property_read_bool(node, "xlnx,include-sg");
> +
> + dma_cap_set(DMA_MEMCPY, xdev->common.cap_mask);
> + xdev->common.device_prep_dma_memcpy =
> xilinx_cdma_prep_memcpy;
> +
> + xdev->common.device_control = xilinx_cdma_device_control;
> + xdev->common.device_issue_pending =
> xilinx_cdma_issue_pending;
> + xdev->common.device_alloc_chan_resources =
> + xilinx_cdma_alloc_chan_resources;
> + xdev->common.device_free_chan_resources =
> + xilinx_cdma_free_chan_resources;
> + xdev->common.device_tx_status = xilinx_tx_status;
> + xdev->common.dev = &pdev->dev;
> +
> + platform_set_drvdata(pdev, xdev);
> +
> + child = of_get_next_child(node, NULL);
> + if (!child) {
> + dev_err(&pdev->dev, "No channel found\n");
> + return PTR_ERR(child);
> + }
> +
> + ret = xilinx_cdma_chan_probe(xdev, child);
> + if (ret) {
> + dev_err(&pdev->dev, "Probing channel failed\n");
> + goto free_chan_resources;
> + }
> +
> + dma_async_device_register(&xdev->common);
> +
> + ret = of_dma_controller_register(node, of_dma_xilinx_xlate, xdev);
> + if (ret) {
> + dev_err(&pdev->dev, "Unable to register DMA to DT\n");
> + dma_async_device_unregister(&xdev->common);
> + goto free_chan_resources;
> + }
> +
> + dev_info(&pdev->dev, "Xilinx AXI CDMA Engine driver Probed!!\n");
> +
> + return 0;
> +
> +free_chan_resources:
> + xilinx_cdma_free_channel(xdev->chan);
> +
> + return ret;
> +}
> +
> +/**
> + * xilinx_cdma_remove - Driver remove function
> + * @pdev: Pointer to the platform_device structure
> + *
> + * Return: Always '0'
> + */
> +static int xilinx_cdma_remove(struct platform_device *pdev) {
> + struct xilinx_cdma_device *xdev = platform_get_drvdata(pdev);
> +
> + of_dma_controller_free(pdev->dev.of_node);
> + dma_async_device_unregister(&xdev->common);
> +
> + xilinx_cdma_free_channel(xdev->chan);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id xilinx_cdma_of_match[] = {
> + { .compatible = "xlnx,axi-cdma-1.00.a", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, xilinx_cdma_of_match);
> +
> +static struct platform_driver xilinx_cdma_driver = {
> + .driver = {
> + .name = "xilinx-cdma",
> + .owner = THIS_MODULE,
> + .of_match_table = xilinx_cdma_of_match,
> + },
> + .probe = xilinx_cdma_probe,
> + .remove = xilinx_cdma_remove,
> +};
> +
> +module_platform_driver(xilinx_cdma_driver);
> +
> +MODULE_AUTHOR("Xilinx, Inc.");
> +MODULE_DESCRIPTION("Xilinx CDMA driver"); MODULE_LICENSE("GPL
> v2");
> diff --git a/include/linux/dma/xilinx_dma.h
> b/include/linux/dma/xilinx_dma.h index 34b98f2..fb74ff7 100644
> --- a/include/linux/dma/xilinx_dma.h
> +++ b/include/linux/dma/xilinx_dma.h
> @@ -41,7 +41,20 @@ struct xilinx_vdma_config {
> int ext_fsync;
> };
>
> +/**
> + * struct xilinx_cdma_config - CDMA Configuration structure
> + * @coalesc: Interrupt coalescing threshold
> + * @delay: Delay counter
> + * @reset: Reset Channel
> + */
> +struct xilinx_cdma_config {
> + int coalesc;
> + int delay;
> + int reset;
> +};
> +
> int xilinx_vdma_channel_set_config(struct dma_chan *dchan,
> struct xilinx_vdma_config *cfg);
> -
> +int xilinx_cdma_channel_set_config(struct dma_chan *dchan,
> + struct xilinx_cdma_config *cfg);
> #endif
> --
> 2.1.2
This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.
More information about the linux-arm-kernel
mailing list