[patch v11 22/23] ARM64 / ACPI: additions of ACPI documentation for arm64
Hanjun Guo
hanjun.guo at linaro.org
Tue Mar 24 07:02:55 PDT 2015
From: Al Stone <al.stone at linaro.org>
One more documentation file are also being added:
A section by section review of the ACPI spec (acpi_object_usage.txt)
to note recommendations and prohibitions on the use of the numerous
ACPI tables and objects. This sets out the current expectations of
the firmware by Linux very explicitly (or as explicitly as I can, for
now).
CC: Suravee Suthikulpanit <Suravee.Suthikulpanit at amd.com>
CC: Yi Li <phoenix.liyi at huawei.com>
CC: Mark Langsdorf <mlangsdo at redhat.com>
CC: Ashwin Chaugule <ashwinc at codeaurora.org>
Acked-by: Robert Richter <rrichter at cavium.com>
Signed-off-by: Al Stone <al.stone at linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo at linaro.org>
---
Documentation/arm64/acpi_object_usage.txt | 593 ++++++++++++++++++++++++++++++
1 file changed, 593 insertions(+)
create mode 100644 Documentation/arm64/acpi_object_usage.txt
diff --git a/Documentation/arm64/acpi_object_usage.txt b/Documentation/arm64/acpi_object_usage.txt
new file mode 100644
index 0000000..96e2273
--- /dev/null
+++ b/Documentation/arm64/acpi_object_usage.txt
@@ -0,0 +1,593 @@
+ACPI Tables
+-----------
+The expectations of individual ACPI tables are discussed in the list that
+follows.
+
+If a section number is used, it refers to a section number in the ACPI
+specification where the object is defined. If "Signature Reserved" is used,
+the table signature (the first four bytes of the table) is the only portion
+of the table recognized by the specification, and the actual table is defined
+outside of the UEFI Forum (see Section 5.2.6 of the specification).
+
+For ACPI on arm64, tables also fall into the following categories:
+
+ -- Required: DSDT, FADT, GTDT, MADT, MCFG, RSDP, SPCR, XSDT
+
+ -- Recommended: BERT, EINJ, ERST, HEST, SSDT
+
+ -- Optional: BGRT, CPEP, CSRT, DRTM, ECDT, FACS, FPDT, MCHI, MPST,
+ MSCT, RASF, SBST, SLIT, SPMI, SRAT, TCPA, TPM2, UEFI
+
+ -- Not supported: BOOT, DBG2, DBGP, DMAR, ETDT, HPET, IBFT, IVRS,
+ LPIT, MSDM, RSDT, SLIC, WAET, WDAT, WDRT, WPBT
+
+
+Table Usage for ARMv8 Linux
+----- ----------------------------------------------------------------
+BERT Section 18.3 (signature == "BERT")
+ == Boot Error Record Table ==
+ Must be supplied if RAS support is provided by the platform. It
+ is recommended this table be supplied.
+
+BOOT Signature Reserved (signature == "BOOT")
+ == simple BOOT flag table ==
+ Microsoft only table, will not be supported.
+
+BGRT Section 5.2.22 (signature == "BGRT")
+ == Boot Graphics Resource Table ==
+ Optional, not currently supported, with no real use-case for an
+ ARM server.
+
+CPEP Section 5.2.18 (signature == "CPEP")
+ == Corrected Platform Error Polling table ==
+ Optional, not currently supported, and not recommended until such
+ time as ARM-compatible hardware is available, and the specification
+ suitably modified.
+
+CSRT Signature Reserved (signature == "CSRT")
+ == Core System Resources Table ==
+ Optional, not currently supported.
+
+DBG2 Signature Reserved (signature == "DBG2")
+ == DeBuG port table 2 ==
+ Microsoft only table, will not be supported.
+
+DBGP Signature Reserved (signature == "DBGP")
+ == DeBuG Port table ==
+ Microsoft only table, will not be supported.
+
+DSDT Section 5.2.11.1 (signature == "DSDT")
+ == Differentiated System Description Table ==
+ A DSDT is required; see also SSDT.
+
+ ACPI tables contain only one DSDT but can contain one or more SSDTs,
+ which are optional. Each SSDT can only add to the ACPI namespace,
+ but cannot modify or replace anything in the DSDT.
+
+DMAR Signature Reserved (signature == "DMAR")
+ == DMA Remapping table ==
+ x86 only table, will not be supported.
+
+DRTM Signature Reserved (signature == "DRTM")
+ == Dynamic Root of Trust for Measurement table ==
+ Optional, not currently supported.
+
+ECDT Section 5.2.16 (signature == "ECDT")
+ == Embedded Controller Description Table ==
+ Optional, not currently supported, but could be used on ARM if and
+ only if one uses the GPE_BIT field to represent an IRQ number, since
+ there are no GPE blocks defined in hardware reduced mode. This would
+ need to be modified in the ACPI specification.
+
+EINJ Section 18.6 (signature == "EINJ")
+ == Error Injection table ==
+ This table is very useful for testing platform response to error
+ conditions; it allows one to inject an error into the system as
+ if it had actually occurred. However, this table should not be
+ shipped with a production system; it should be dynamically loaded
+ and executed with the ACPICA tools only during testing.
+
+ERST Section 18.5 (signature == "ERST")
+ == Error Record Serialization Table ==
+ On a platform supports RAS, this table must be supplied if it is not
+ UEFI-based; if it is UEFI-based, this table may be supplied. When this
+ table is not present, UEFI run time service will be utilized to save
+ and retrieve hardware error information to and from a persistent store.
+
+ETDT Signature Reserved (signature == "ETDT")
+ == Event Timer Description Table ==
+ Obsolete table, will not be supported.
+
+FACS Section 5.2.10 (signature == "FACS")
+ == Firmware ACPI Control Structure ==
+ It is unlikely that this table will be terribly useful. If it is
+ provided, the Global Lock will NOT be used since it is not part of
+ the hardware reduced profile, and only 64-bit address fields will
+ be considered valid.
+
+FADT Section 5.2.9 (signature == "FACP")
+ == Fixed ACPI Description Table ==
+ Required for arm64.
+
+ The HW_REDUCED_ACPI flag must be set. All of the fields that are
+ to be ignored when HW_REDUCED_ACPI is set are expected to be set to
+ zero.
+
+ If an FACS table is provided, the X_FIRMWARE_CTRL field is to be
+ used, not FIRMWARE_CTRL.
+
+ If PSCI is used (as is recommended), make sure that ARM_BOOT_ARCH is
+ filled in properly -- that the PSCI_COMPLIANT flag is set and that
+ PSCI_USE_HVC is set or unset as needed (see table 5-37).
+
+ For the DSDT that is also required, the X_DSDT field is to be used,
+ not the DSDT field.
+
+FPDT Section 5.2.23 (signature == "FPDT")
+ == Firmware Performance Data Table ==
+ Optional, not currently supported.
+
+GTDT Section 5.2.24 (signature == "GTDT")
+ == Generic Timer Description Table ==
+ Required for arm64.
+
+HEST Section 18.3.2 (signature == "HEST")
+ == Hardware Error Source Table ==
+ Until further error source types are defined, use only types 6 (AER
+ Root Port), 7 (AER Endpoint), 8 (AER Bridge), or 9 (Generic Hardware
+ Error Source). Firmware first error handling is possible if and only
+ if Trusted Firmware is being used on arm64.
+
+ Must be supplied if RAS support is provided by the platform. It
+ is recommended this table be supplied.
+
+HPET Signature Reserved (signature == "HPET")
+ == High Precision Event timer Table ==
+ x86 only table, will not be supported.
+
+IBFT Signature Reserved (signature == "IBFT")
+ == iSCSI Boot Firmware Table ==
+ Microsoft defined table, support TBD.
+
+IVRS Signature Reserved (signature == "IVRS")
+ == I/O Virtualization Reporting Structure ==
+ x86_64 (AMD) only table, will not be supported.
+
+LPIT Signature Reserved (signature == "LPIT")
+ == Low Power Idle Table ==
+ x86 only table as of ACPI 5.1; future versions have been adapted for
+ use with ARM and will be recommended in order to support ACPI power
+ management.
+
+MADT Section 5.2.12 (signature == "APIC")
+ == Multiple APIC Description Table ==
+ Required for arm64. Only the GIC interrupt controller structures
+ should be used (types 0xA - 0xE).
+
+MCFG Signature Reserved (signature == "MCFG")
+ == Memory-mapped ConFiGuration space ==
+ If the platform supports PCI/PCIe, an MCFG table is required.
+
+MCHI Signature Reserved (signature == "MCHI")
+ == Management Controller Host Interface table ==
+ Optional, not currently supported.
+
+MPST Section 5.2.21 (signature == "MPST")
+ == Memory Power State Table ==
+ Optional, not currently supported.
+
+MSDM Signature Reserved (signature == "MSDM")
+ == Microsoft Data Management table ==
+ Microsoft only table, will not be supported.
+
+MSCT Section 5.2.19 (signature == "MSCT")
+ == Maximum System Characteristic Table ==
+ Optional, not currently supported.
+
+RASF Section 5.2.20 (signature == "RASF")
+ == RAS Feature table ==
+ Optional, not currently supported.
+
+RSDP Section 5.2.5 (signature == "RSD PTR")
+ == Root System Description PoinTeR ==
+ Required for arm64.
+
+RSDT Section 5.2.7 (signature == "RSDT")
+ == Root System Description Table ==
+ Since this table can only provide 32-bit addresses, it is deprecated
+ on arm64, and will not be used.
+
+SBST Section 5.2.14 (signature == "SBST")
+ == Smart Battery Subsystem Table ==
+ Optional, not currently supported.
+
+SLIC Signature Reserved (signature == "SLIC")
+ == Software LIcensing table ==
+ Microsoft only table, will not be supported.
+
+SLIT Section 5.2.17 (signature == "SLIT")
+ == System Locality distance Information Table ==
+ Optional in general, but required for NUMA systems.
+
+SPCR Signature Reserved (signature == "SPCR")
+ == Serial Port Console Redirection table ==
+ Required for arm64.
+
+SPMI Signature Reserved (signature == "SPMI")
+ == Server Platform Management Interface table ==
+ Optional, not currently supported.
+
+SRAT Section 5.2.16 (signature == "SRAT")
+ == System Resource Affinity Table ==
+ Optional, but if used, only the GICC Affinity structures are read.
+ To support NUMA, this table is required.
+
+SSDT Section 5.2.11.2 (signature == "SSDT")
+ == Secondary System Description Table ==
+ These tables are a continuation of the DSDT; these are recommended
+ for use with devices that can be added to a running system, but can
+ also serve the purpose of dividing up device descriptions into more
+ manageable pieces.
+
+ An SSDT can only ADD to the ACPI namespace. It cannot modify or
+ replace existing device descriptions already in the namespace.
+
+ These tables are optional, however. ACPI tables should contain only
+ one DSDT but can contain many SSDTs.
+
+TCPA Signature Reserved (signature == "TCPA")
+ == Trusted Computing Platform Alliance table ==
+ Optional, not currently supported, and may need changes to fully
+ interoperate with arm64.
+
+TPM2 Signature Reserved (signature == "TPM2")
+ == Trusted Platform Module 2 table ==
+ Optional, not currently supported, and may need changes to fully
+ interoperate with arm64.
+
+UEFI Signature Reserved (signature == "UEFI")
+ == UEFI ACPI data table ==
+ Optional, not currently supported. No known use case for arm64,
+ at present.
+
+WAET Signature Reserved (signature == "WAET")
+ == Windows ACPI Emulated devices Table ==
+ Microsoft only table, will not be supported.
+
+WDAT Signature Reserved (signature == "WDAT")
+ == Watch Dog Action Table ==
+ Microsoft only table, will not be supported.
+
+WDRT Signature Reserved (signature == "WDRT")
+ == Watch Dog Resource Table ==
+ Microsoft only table, will not be supported.
+
+WPBT Signature Reserved (signature == "WPBT")
+ == Windows Platform Binary Table ==
+ Microsoft only table, will not be supported.
+
+XSDT Section 5.2.8 (signature == "XSDT")
+ == eXtended System Description Table ==
+ Required for arm64.
+
+
+ACPI Objects
+------------
+The expectations on individual ACPI objects are discussed in the list that
+follows:
+
+Name Section Usage for ARMv8 Linux
+---- ------------ -------------------------------------------------
+_ADR 6.1.1 Use as needed.
+
+_BBN 6.5.5 Use as needed; PCI-specific.
+
+_BDN 6.5.3 Optional; not likely to be used on arm64.
+
+_CCA 6.2.17 This method should be defined for all bus masters
+ on arm64. While cache coherency is assumed, making
+ it explicit ensures the kernel will set up DMA as
+ it should.
+
+_CDM 6.2.1 Optional, to be used only for processor devices.
+
+_CID 6.1.2 Use as needed.
+
+_CLS 6.1.3 Use as needed.
+
+_CRS 6.2.2 Required on arm64.
+
+_DCK 6.5.2 Optional; not likely to be used on arm64.
+
+_DDN 6.1.4 This field can be used for a device name. However,
+ it is meant for DOS device names (e.g., COM1), so be
+ careful of its use across OSes.
+
+_DEP 6.5.8 Use as needed.
+
+_DIS 6.2.3 Optional, for power management use.
+
+_DLM 5.7.5 Optional.
+
+_DMA 6.2.4 Optional.
+
+_DSD 6.2.5 To be used with caution. If this object is used, try
+ to use it within the constraints already defined by the
+ Device Properties UUID. Only in rare circumstances
+ should it be necessary to create a new _DSD UUID.
+
+ In either case, submit the _DSD definition along with
+ any driver patches for discussion, especially when
+ device properties are used. A driver will not be
+ considered complete without a corresponding _DSD
+ description. Once approved by kernel maintainers,
+ the UUID or device properties must then be registered
+ with the UEFI Forum; this may cause some iteration as
+ more than one OS will be registering entries.
+
+_DSM Do not use this method. It is not standardized, the
+ return values are not well documented, and it is
+ currently a frequent source of error.
+
+_DSW 7.2.1 Use as needed; power management specific.
+
+_EDL 6.3.1 Optional.
+
+_EJD 6.3.2 Optional.
+
+_EJx 6.3.3 Optional.
+
+_FIX 6.2.7 x86 specific, not used on arm64.
+
+\_GL 5.7.1 This object is not to be used in hardware reduced
+ mode, and therefore should not be used on arm64.
+
+_GLK 6.5.7 This object requires a global lock be defined; there
+ is no global lock on arm64 since it runs in hardware
+ reduced mode. Hence, do not use this object on arm64.
+
+\_GPE 5.3.1 This namespace is for x86 use only. Do not use it
+ on arm64.
+
+_GSB 6.2.7 Optional.
+
+_HID 6.1.5 Use as needed. This is the primary object to use in
+ device probing, though _CID and _CLS may also be used.
+
+_HPP 6.2.8 Optional, PCI specific.
+
+_HPX 6.2.9 Optional, PCI specific.
+
+_HRV 6.1.6 Optional, use as needed to clarify device behavior; in
+ some cases, this may be easier to use than _DSD.
+
+_INI 6.5.1 Not required, but can be useful in setting up devices
+ when UEFI leaves them in a state that may not be what
+ the driver expects before it starts probing.
+
+_IRC 7.2.15 Use as needed; power management specific.
+
+_LCK 6.3.4 Optional.
+
+_MAT 6.2.10 Optional; see also the MADT.
+
+_MLS 6.1.7 Optional, but highly recommended for use in
+ internationalization.
+
+_OFF 7.1.2 It is recommended to define this method for any device
+ that can be turned on or off.
+
+_ON 7.1.3 It is recommended to define this method for any device
+ that can be turned on or off.
+
+\_OS 5.7.3 This method will return "Linux" by default (this is
+ the value of the macro ACPI_OS_NAME on Linux). The
+ command line parameter acpi_os=<string> can be used
+ to set it to some other value.
+
+_OSC 6.2.11 This method can be a global method in ACPI (i.e.,
+ \_SB._OSC), or it may be associated with a specific
+ device (e.g., \_SB.DEV0._OSC), or both. When used
+ as a global method, only capabilities published in
+ the ACPI specification are allowed. When used as
+ a device-specific method, the process described for
+ using _DSD MUST be used to create an _OSC definition;
+ out-of-process use of _OSC is not allowed. That is,
+ submit the device-specific _OSC usage description as
+ part of the kernel driver submission, get it approved
+ by the kernel community, then register it with the
+ UEFI Forum.
+
+\_OSI 5.7.2 Deprecated on ARM64. Any invocation of this method
+ will print a warning on the console and return false.
+ That is, as far as ACPI firmware is concerned, _OSI
+ cannot be used to determine what sort of system is
+ being used or what functionality is provided. The
+ _OSC method is to be used instead.
+
+_OST 6.3.5 Optional.
+
+_PDC 8.4.1 Deprecated, do not use on arm64.
+
+\_PIC 5.8.1 The method should not be used. On arm64, the only
+ interrupt model available is GIC.
+
+_PLD 6.1.8 Optional.
+
+\_PR 5.3.1 This namespace is for x86 use only on legacy systems.
+ Do not use it on arm64.
+
+_PRS 6.2.12 Optional.
+
+_PRT 6.2.13 Required as part of the definition of all PCI root
+ devices.
+
+_PRW 7.2.13 Use as needed; power management specific.
+
+_PRx 7.2.8-11 Use as needed; power management specific. If _PR0 is
+ defined, _PR3 must also be defined.
+
+_PSC 7.2.6 Use as needed; power management specific.
+
+_PSE 7.2.7 Use as needed; power management specific.
+
+_PSW 7.2.14 Use as needed; power management specific.
+
+_PSx 7.2.2-5 Use as needed; power management specific. If _PS0 is
+ defined, _PS3 must also be defined. If clocks or
+ regulators need adjusting to be consistent with power
+ usage, change them in these methods.
+
+\_PTS 7.3.1 Use as needed; power management specific.
+
+_PXM 6.2.14 Optional.
+
+_REG 6.5.4 Use as needed.
+
+\_REV 5.7.4 Always returns the latest version of ACPI supported.
+
+_RMV 6.3.6 Optional.
+
+\_SB 5.3.1 Required on arm64; all devices must be defined in this
+ namespace.
+
+_SEG 6.5.6 Use as needed; PCI-specific.
+
+\_SI 5.3.1, Optional.
+ 9.1
+
+_SLI 6.2.15 Optional; recommended when SLIT table is in use.
+
+_STA 6.3.7, It is recommended to define this method for any device
+ 7.1.4 that can be turned on or off.
+
+_SRS 6.2.16 Optional; see also _PRS.
+
+_STR 6.1.10 Recommended for conveying device names to end users;
+ this is preferred over using _DDN.
+
+_SUB 6.1.9 Use as needed; _HID or _CID are preferred.
+
+_SUN 6.1.11 Optional.
+
+\_Sx 7.3.2 Use as needed; power management specific.
+
+_SxD 7.2.16-19 Use as needed; power management specific.
+
+_SxW 7.2.20-24 Use as needed; power management specific.
+
+_SWS 7.3.3 Use as needed; power management specific; this may
+ require specification changes for use on arm64.
+
+\_TTS 7.3.4 Use as needed; power management specific.
+
+\_TZ 5.3.1 Optional.
+
+_UID 6.1.12 Recommended for distinguishing devices of the same
+ class; define it if at all possible.
+
+\_WAK 7.3.5 Use as needed; power management specific.
+
+
+ACPI Event Model
+----------------
+Do not use GPE block devices; these are not supported in the hardware reduced
+profile used by arm64. Since there are no GPE blocks defined for use on ARM
+platforms, GPIO-signaled interrupts should be used for creating system events.
+
+
+ACPI Processor Control
+----------------------
+Section 8 of the ACPI specification is currently undergoing change that
+should be completed in the 6.0 version of the specification. Processor
+performance control will be handled differently for arm64 at that point
+in time. Processor aggregator devices (section 8.5) will not be used,
+for example, but another similar mechanism instead.
+
+While UEFI constrains what we can say until the release of 6.0, it is
+recommended that CPPC (8.4.5) be used as the primary model. This will
+still be useful into the future. C-states and P-states will still be
+provided, but most of the current design work appears to favor CPPC.
+
+Further, it is essential that the ARMv8 SoC provide a fully functional
+implementation of PSCI; this will be the only mechanism supported by ACPI
+to control CPU power state (including secondary CPU booting).
+
+More details will be provided on the release of the ACPI 6.0 specification.
+
+
+ACPI System Address Map Interfaces
+----------------------------------
+In Section 15 of the ACPI specification, several methods are mentioned as
+possible mechanisms for conveying memory resource information to the kernel.
+For arm64, we will only support UEFI for booting with ACPI, hence the UEFI
+GetMemoryMap() boot service is the only mechanism that will be used.
+
+
+ACPI Platform Error Interfaces (APEI)
+-------------------------------------
+The APEI tables supported are described above.
+
+APEI requires the equivalent of an SCI and an NMI on ARMv8. The SCI is used
+to notify the OSPM of errors that have occurred but can be corrected and the
+system can continue correct operation, even if possibly degraded. The NMI is
+used to indicate fatal errors that cannot be corrected, and require immediate
+attention.
+
+Since there is no direct equivalent of the x86 SCI or NMI, arm64 handles
+these slightly differently. The SCI is handled as a normal GPIO-signaled
+interrupt; given that these are corrected (or correctable) errors being
+reported, this is sufficient. The NMI is emulated as the highest priority
+GPIO-signaled interrupt possible. This implies some caution must be used
+since there could be interrupts at higher privilege levels or even interrupts
+at the same priority as the emulated NMI. In Linux, this should not be the
+case but one should be aware it could happen.
+
+
+ACPI Objects Not Supported on ARM64
+-----------------------------------
+While this may change in the future, there are several classes of objects
+that can be defined, but are not currently of general interest to ARM servers.
+
+These are not supported:
+
+ -- Section 9.2: ambient light sensor devices
+
+ -- Section 9.3: battery devices
+
+ -- Section 9.4: lids (e.g., laptop lids)
+
+ -- Section 9.8.2: IDE controllers
+
+ -- Section 9.9: floppy controllers
+
+ -- Section 9.10: GPE block devices
+
+ -- Section 9.15: PC/AT RTC/CMOS devices
+
+ -- Section 9.16: user presence detection devices
+
+ -- Section 9.17: I/O APIC devices; all GICs must be enumerable via MADT
+
+ -- Section 9.18: time and alarm devices (see 9.15)
+
+
+ACPI Objects Not Yet Implemented
+--------------------------------
+While these objects have x86 equivalents, and they do make some sense in ARM
+servers, there is either no hardware available at present, or in some cases
+there may not yet be a non-ARM implementation. Hence, they are currently not
+implemented though that may change in the future.
+
+Not yet implemented are:
+
+ -- Section 10: power source and power meter devices
+
+ -- Section 11: thermal management
+
+ -- Section 12: embedded controllers interface
+
+ -- Section 13: SMBus interfaces
+
+ -- Section 17: NUMA support (prototypes have been submitted for
+ review)
--
1.9.1
More information about the linux-arm-kernel
mailing list