[PATCH v2 2/5] PCI: st: Add Device Tree bindings for sti pcie

[Liviu Dudau]

Hi Gabriel,

On Mon, Mar 16, 2015 at 02:20:32PM +0000, Gabriel FERNANDEZ wrote:
> sti pcie is built around a Synopsis Designware PCIe IP.
> 
> Signed-off-by: Fabrice Gasnier <fabrice.gasnier at st.com>
> Signed-off-by: Gabriel Fernandez <gabriel.fernandez at linaro.org>
> ---
>  Documentation/devicetree/bindings/pci/st-pcie.txt | 54 +++++++++++++++++++++++
>  1 file changed, 54 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/st-pcie.txt
> 
> diff --git a/Documentation/devicetree/bindings/pci/st-pcie.txt b/Documentation/devicetree/bindings/pci/st-pcie.txt
> new file mode 100644
> index 0000000..94aae2d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/st-pcie.txt
> @@ -0,0 +1,54 @@
> +STMicroelectronics STi PCIe controller
> +
> +This PCIe host controller is based on the Synopsis Designware PCIe IP
> +and thus inherits all the common properties defined in designware-pcie.txt.
> +
> +Required properties:
> + - compatible: "st,stih407-pcie"
> + - reg: base address and length of the pcie controller, mem-window address
> +   and length available to the controller.
> + - interrupts: A list of interrupt outputs of the controller. Must contain an
> +   entry for each entry in the interrupt-names property.
> + - interrupt-names: Should be "msi". STi interrupt that is asserted when an
> +   MSI is received.
> + - st,syscfg : should be a phandle of the syscfg node. Also contains syscfg
> +   offset for IP configuration.
> + - resets, reset-names: the power-down and soft-reset lines of PCIe IP.
> +   Associated names must be "powerdown" and "softreset".
> + - phys, phy-names: the phandle for the PHY device.
> +   Associated name must be "pcie"
> +
> +Optional properties:
> + - reset-gpio: a GPIO spec to define which pin is connected to the bus reset.
> +
> +Example:
> +
> +pcie0: pcie at 9b00000 {
> +	compatible = "st,stih407-pcie", "snps,dw-pcie";
> +	device_type = "pci";
> +	reg = <0x09b00000 0x4000>,	/* dbi cntrl registers */
> +	      <0x2fff0000 0x00010000>,	/* configuration space */
> +	      <0x40000000 0x80000000>;	/* lmi mem window */
> +	reg-names = "dbi", "config", "mem-window";
> +	st,syscfg = <&syscfg_core 0xd8 0xe0>;
> +	#address-cells = <3>;
> +	#size-cells = <2>;
> +	ranges = <0x00000800 0 0x2fff0000 0x2fff0000 0 0x00010000   /* configuration space */

Unless you are trying to support some legacy code please remove the configuration space from the ranges.
There is no resource type associated with config space and the generic parser will give you back an
invalid resource type. The other reason for that is that if you really claim to be ECAM compliant by
adding the config space here you need way more than 64K of space.

Best regards,
Liviu

> +		  0x82000000 0 0x20000000 0x20000000 0 0x0FFF0000>; /* non-prefetchable memory */
> +	num-lanes = <1>;
> +	interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
> +	interrupt-names = "msi";
> +	#interrupt-cells = <1>;
> +	interrupt-map-mask = <0 0 0 7>;
> +	interrupt-map = <0 0 0 1 &intc GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, /* INT A */
> +			<0 0 0 2 &intc GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, /* INT B */
> +			<0 0 0 3 &intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, /* INT C */
> +			<0 0 0 4 &intc GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; /* INT D */
> +
> +	resets = <&powerdown STIH407_PCIE0_POWERDOWN>,
> +		 <&softreset STIH407_PCIE0_SOFTRESET>;
> +	reset-names = "powerdown",
> +		      "softreset";
> +	phys = <&phy_port0 PHY_TYPE_PCIE>;
> +	phy-names = "pcie";
> +};
> -- 
> 1.9.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

-- 
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯