[PATCH] arm64: dts: add APM Merlin Board device tree

[Mark Rutland]

Hi,

On Tue, Mar 10, 2015 at 05:10:54PM +0000, Feng Kan wrote:
> This patch adds the support for APM Merlin board. The Merlin board
> is based on the APM X-Gene Shadowcat SoC. This DTS enables PMU,
> SATA and Serial.
> 
> Signed-off-by: Feng Kan <fkan at apm.com>
> ---
>  arch/arm64/boot/dts/apm/apm-merlin.dts     |  39 ++++++++
>  arch/arm64/boot/dts/apm/apm-shadowcat.dtsi | 154 +++++++++++++++++++++++++++++
>  2 files changed, 193 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/apm/apm-merlin.dts
>  create mode 100644 arch/arm64/boot/dts/apm/apm-shadowcat.dtsi

[...]

> +	memory {
> +		device_type = "memory";
> +		reg = < 0x1 0x00000000 0x0 0x80000000 >;
> +	};

[...]

> +		cpu at 000 {
> +			device_type = "cpu";
> +			compatible = "apm,strega", "arm,armv8";
> +			reg = <0x0 0x000>;
> +			enable-method = "spin-table";

I take it that as with Potenza there won't be PSCI?

> +			cpu-release-addr = <0x1 0x0000fff8>;
> +		};

The range covered by the cpu-release-addr exists in the memory node and
there's no /memreserve/, so this is broken.

Please fix this so the release address and the code the secondaries are
executing to poll it can't be accidentally clobbered.

[...]

> +	gic: interrupt-controller at 78090000 {
> +		compatible = "arm,cortex-a15-gic";
> +		#interrupt-cells = <3>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		interrupt-controller;
> +		interrupts = <1 9 0xf04>;	/* GIC Maintenence IRQ */
> +		ranges = <0 0 0 0x79000000 0x0 0x800000>; /* MSI Range */

Nothing in this patch seems to require this ranges entry. Remove it
until it's necessary.

> +		reg = <0x0 0x78090000 0x0 0x10000>,	/* GIC Dist */
> +		      <0x0 0x780A0000 0x0 0x20000>,	/* GIC CPU */
> +		      <0x0 0x780C0000 0x0 0x10000>,	/* GIC VCPU Control */
> +		      <0x0 0x780E0000 0x0 0x20000>;	/* GIC VCPU */
> +	};
> +
> +	pmu {
> +		compatible = "arm,armv8-pmuv3";
> +		interrupts = <1 12 0xff04>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <1 0 0xff04>,	/* Secure Phys IRQ */
> +			     <1 13 0xff04>,	/* Non-secure Phys IRQ */
> +			     <1 14 0xff04>,	/* Virt IRQ */
> +			     <1 15 0xff04>;	/* Hyp IRQ */
> +		clock-frequency = <50000000>;

CNTFRQ should be programmed (on all CPUs) by the FW/bootloader prior to
entering the kernel.

If it isn't configured, virtualization is broken.

If it is configured, this is unnecessary and can be dropped from the
dts.

[...]

> +		serial0: serial at 10600000 {
> +			device_type = "serial";
> +			compatible = "ns16550";
> +			reg = <0 0x10600000 0x0 0x1000>;
> +			reg-shift = <2>;
> +			clock-frequency = <10000000>;
> +			interrupt-parent = <&gic>;
> +			interrupts = <0x0 0x4c 0x4>;
> +		};

It would be good if /chosen/stdout-path were set up appropriately for
this.

Thanks,
Mark.