[PATCH v5] dma: Add Xilinx AXI Direct Memory Access Engine driver support

[Appana Durga Kedareswara Rao]

Hi Josh,

        Thanks for reviewing the patch

> -----Original Message-----
> From: Josh Cartwright [mailto:joshc at ni.com]
> Sent: Tuesday, March 03, 2015 12:12 AM
> To: Appana Durga Kedareswara Rao
> Cc: dan.j.williams at intel.com; vinod.koul at intel.com; Michal Simek; Soren
> Brinkmann; Srikanth Vemula; linux-kernel at vger.kernel.org; Srikanth
> Thokala; Anirudha Sarangi; dmaengine at vger.kernel.org; Appana Durga
> Kedareswara Rao; linux-arm-kernel at lists.infradead.org
> Subject: Re: [PATCH v5] dma: Add Xilinx AXI Direct Memory Access Engine
> driver support
>
> Hello!
>
> I looked through your driver and have some comments.
>
> On Mon, Mar 02, 2015 at 11:25:11PM +0530, Kedareswara rao Appana wrote:
> > This is the driver for the AXI Direct Memory Access (AXI DMA) core,
> > which is a soft Xilinx IP core that provides high- bandwidth direct
> > memory access between memory and AXI4-Stream type target
> peripherals.
> >
> > Signed-off-by: Srikanth Thokala <sthokal at xilinx.com>
> > Signed-off-by: Kedareswara rao Appana <appanad at xilinx.com>
> [..]
> > +++ b/drivers/dma/Kconfig
> > @@ -425,6 +425,19 @@ config IMG_MDC_DMA
> >     help
> >       Enable support for the IMG multi-threaded DMA controller (MDC).
> >
> > +config XILINX_DMA
> > +   tristate "Xilinx AXI DMA Engine"
> > +   depends on (ARCH_ZYNQ || MICROBLAZE)
>
> Why do you need this dependency?  I'm assuming this IP has usefulness
> outside of microblaze and Zynq.
>
> > +   select DMA_ENGINE
> > +   help
> > +     Enable support for Xilinx AXI DMA Soft IP.
> > +
> > +   This engine provides high-bandwidth direct memory access
> > +   between memory and AXI4-Stream type target peripherals.
> > +   It has two stream interfaces/channels, Memory Mapped to
> > +   Stream (MM2S) and Stream to Memory Mapped (S2MM) for the
> > +   data transfers.
>
> Odd indention here.  At least indent this paragraph like the sentence above.

Ok Will do.

>
> [..]
> > +++ b/drivers/dma/xilinx/xilinx_dma.c
> [..]
> > +/**
> > + * xilinx_dma_halt - Halt DMA channel
> > + * @chan: Driver specific DMA channel  */ static void
> > +xilinx_dma_halt(struct xilinx_dma_chan *chan) {
> > +   int loop = XILINX_DMA_LOOP_COUNT;
> > +
> > +   dma_ctrl_clr(chan, XILINX_DMA_REG_CONTROL,
> > +                XILINX_DMA_CR_RUNSTOP_MASK);
> > +
> > +   /* Wait for the hardware to halt */
> > +   do {
> > +           if (dma_ctrl_read(chan, XILINX_DMA_REG_STATUS) &
> > +                   XILINX_DMA_SR_HALTED_MASK)
> > +                   break;
> > +   } while (loop--);
> > +
> > +   if (!loop) {
>
> Looks like a very subtle off-by-one error here.  (And elsewhere you use this
> pattern).
>

Ok Will do this change in the next version of the patch.

Regards,
Kedar.

>   Josh


This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.