[PATCH v2 16/18] ARM: dts: Introduce STM32F429 MCU
Andreas Färber
afaerber at suse.de
Mon Mar 2 09:42:15 PST 2015
Hi Maxime,
Please don't put the whole world in To, that makes replying to you much
harder. You can put maintainers in CC instead.
Am 20.02.2015 um 19:01 schrieb Maxime Coquelin:
> The STMicrolectornics's STM32F419 MCU has the following main features:
> - Cortex-M4 core running up to @180MHz
> - 2MB internal flash, 256KBytes internal RAM
> - FMC controller to connect SDRAM, NOR and NAND memories
> - SD/MMC/SDIO support
> - Ethernet controller
> - USB OTFG FS & HS controllers
> - I2C, SPI, CAN busses support
> - Several 16 & 32 bits general purpose timers
> - Serial Audio interface
> - LCD controller
>
> Signed-off-by: Maxime Coquelin <mcoquelin.stm32 at gmail.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/stm32f429-disco.dts | 41 ++++
> arch/arm/boot/dts/stm32f429.dtsi | 396 ++++++++++++++++++++++++++++++++++
> 3 files changed, 438 insertions(+)
> create mode 100644 arch/arm/boot/dts/stm32f429-disco.dts
> create mode 100644 arch/arm/boot/dts/stm32f429.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 91bd5bd..d7da0ef 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -442,6 +442,7 @@ dtb-$(CONFIG_ARCH_STI)+= stih407-b2120.dtb \
> stih416-b2000.dtb \
> stih416-b2020.dtb \
> stih416-b2020e.dtb
> +dtb-$(CONFIG_ARCH_STM32)+= stm32f429-disco.dtb
> dtb-$(CONFIG_MACH_SUN4I) += \
> sun4i-a10-a1000.dtb \
> sun4i-a10-ba10-tvbox.dtb \
> diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
> new file mode 100644
> index 0000000..0e79cc1
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32f429-disco.dts
> @@ -0,0 +1,41 @@
Add a suitable license header here? There had been attempts to
dual-license as GPL and MIT/X11.
> +/dts-v1/;
> +#include "stm32f429.dtsi"
> +
> +/ {
> + model = "STMicroelectronics's STM32F429i-DISCO board";
"'s" seems uncommon here and "s's" looks wrong. Just use
"STMicroelectronics STM32F429I-DISCO board"?
> + compatible = "st,stm32f429i-disco", "st,stm32f429";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200 root=/dev/ram rdinit=/linuxrc";
> + linux,stdout-path = &usart1;
I have actually been using USART3, following a guide I found on GitHub.
Which pins do you use for USART1, and is one better than the other?
> + };
> +
> + memory {
> + reg = <0xd0000000 0x800000>;
I have it at 0x90000000!
> + };
> +
> + aliases {
> + ttyS0 = &usart1;
Why ttyS0 here? Shouldn't that be serial0 by convention?
> + };
> +
> + soc {
> + usart1: usart at 40011000 {
> + status = "okay";
> + };
This is a new target, so please use the new-style &usart1 {...};
reference rather than replicating the hierarchy.
> +
> + leds {
These LEDs are definitely not on the SoC, they're on the board. Please
move one level up.
> + compatible = "gpio-leds";
In this file you're being parsimonious with newline, yet in the .dtsi
you unnecessarily add newlines before the trailing status property.
> + red {
> + #gpio-cells = <2>;
This looks weird. Drop it?
> + label = "Front Panel LED";
"Front Panel"? Both LEDs are on the front, and several other
architectures avoid spaces in the label for accessing it from /sys.
> + gpios = <&gpiog 14 0>;
GPIO_ACTIVE_HIGH
> + linux,default-trigger = "heartbeat";
Suggest to leave both off by default.
> + };
> + green {
> + #gpio-cells = <2>;
Ditto.
> + gpios = <&gpiog 13 0>;
Ditto.
> + default-state = "off";
> + };
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
> new file mode 100644
> index 0000000..5b3442a
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32f429.dtsi
> @@ -0,0 +1,396 @@
> +/*
> + * Device tree for STM32F429
License?
> + */
> +#include "armv7-m.dtsi"
> +#include <dt-bindings/pinctrl/pinctrl-stm32.h>
> +#include <dt-bindings/reset/st,stm32f429.h>
> +
> +/ {
> +
> + aliases {
> + gpio0 = &gpioa;
> + gpio1 = &gpiob;
> + gpio2 = &gpioc;
> + gpio3 = &gpiod;
> + gpio4 = &gpioe;
> + gpio5 = &gpiof;
> + gpio6 = &gpiog;
> + gpio7 = &gpioh;
> + gpio8 = &gpioi;
> + gpio9 = &gpioj;
> + gpio10 = &gpiok;
> + };
> +
> + clocks {
> + clk_sysclk: clk-sysclk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <180000000>;
> + };
> +
> + clk_hclk: clk-hclk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <180000000>;
> + };
> +
> + clk_pclk1: clk-pclk1 {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <45000000>;
> + };
> +
> + clk_pclk2: clk-pclk2 {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <90000000>;
> + };
> +
> + clk_pmtr1: clk-pmtr1 {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <90000000>;
> + };
> +
> + clk_pmtr2: clk-pmtr2 {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <180000000>;
> + };
> +
> + clk_systick: clk-systick {
> + compatible = "fixed-factor-clock";
> + clocks = <&clk_hclk>;
> + #clock-cells = <0>;
> + clock-div = <8>;
> + clock-mult = <1>;
> + };
Most of these should be replaceable with my clk driver.
> + };
> +
> + systick: timer at e000e010 {
> + clocks = <&clk_systick>;
> +
> + status = "okay";
> + };
&systick {...};
> +
> + soc {
> + reset: reset at 40023810 {
> + #reset-cells = <1>;
> + compatible = "st,stm32-reset";
> + reg = <0x40023810 0x18>;
> + };
Still, this feels wrong, given that it's an RCC IP block...
> +
> + pin-controller {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "st,stm32-pinctrl";
> + ranges = <0 0x40020000 0x3000>;
> +
> + gpioa: gpio at 40020000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x0 0x400>;
> + resets = <&reset GPIOA_RESET>;
> + st,bank-name = "GPIOA";
> + };
> +
> + gpiob: gpio at 40020400 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x400 0x400>;
> + resets = <&reset GPIOB_RESET>;
> + st,bank-name = "GPIOB";
> + };
> +
> + gpioc: gpio at 40020800 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x800 0x400>;
> + resets = <&reset GPIOC_RESET>;
> + st,bank-name = "GPIOC";
> + };
> +
> + gpiod: gpio at 40020c00 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0xc00 0x400>;
> + resets = <&reset GPIOD_RESET>;
> + st,bank-name = "GPIOD";
> + };
> +
> + gpioe: gpio at 40021000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x1000 0x400>;
> + resets = <&reset GPIOE_RESET>;
> + st,bank-name = "GPIOE";
> + };
> +
> + gpiof: gpio at 40021400 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x1400 0x400>;
> + resets = <&reset GPIOF_RESET>;
> + st,bank-name = "GPIOF";
> + };
> +
> + gpiog: gpio at 40021800 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x1800 0x400>;
> + resets = <&reset GPIOG_RESET>;
> + st,bank-name = "GPIOG";
> + };
> +
> + gpioh: gpio at 40021c00 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x1c00 0x400>;
> + resets = <&reset GPIOH_RESET>;
> + st,bank-name = "GPIOH";
> + };
> +
> + gpioi: gpio at 40022000 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x2000 0x400>;
> + resets = <&reset GPIOI_RESET>;
> + st,bank-name = "GPIOI";
> + };
> +
> + gpioj: gpio at 40022400 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x2400 0x400>;
> + resets = <&reset GPIOJ_RESET>;
> + st,bank-name = "GPIOJ";
> + };
> +
> + gpiok: gpio at 40022800 {
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x2800 0x400>;
> + resets = <&reset GPIOK_RESET>;
> + st,bank-name = "GPIOK";
> + };
> +
> + usart1 {
> + pinctrl_usart1: usart1-0 {
> + st,pins {
> + tx = <&gpioa 9 ALT7 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioa 10 ALT7 NO_PULL>;
> + };
> + };
> + };
> +
> + usart2 {
> + pinctrl_usart2: usart2-0 {
> + st,pins {
> + tx = <&gpioa 2 ALT7 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioa 3 ALT7 NO_PULL>;
> + };
> + };
> + };
> +
> + usart3 {
> + pinctrl_usart3: usart3-0 {
> + st,pins {
> + tx = <&gpiob 10 ALT7 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpiob 11 ALT7 NO_PULL>;
> + };
> + };
> + };
> +
> + usart4 {
> + pinctrl_usart4: usart4-0 {
> + st,pins {
> + tx = <&gpioa 0 ALT8 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioa 1 ALT8 NO_PULL>;
> + };
> + };
> + };
> +
> + usart5 {
> + pinctrl_usart5: usart5-0 {
> + st,pins {
> + tx = <&gpioc 12 ALT8 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpiod 2 ALT8 NO_PULL>;
> + };
> + };
> + };
> +
> + usart6 {
> + pinctrl_usart6: usart6-0 {
> + st,pins {
> + tx = <&gpioc 6 ALT8 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioc 7 ALT8 NO_PULL>;
> + };
> + };
> + };
> +
> + usart7 {
> + pinctrl_usart7: usart7-0 {
> + st,pins {
> + tx = <&gpioe 8 ALT8 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioe 7 ALT8 NO_PULL>;
> + };
> + };
> + };
> +
> + usart8 {
> + pinctrl_usart8: usart8-0 {
> + st,pins {
> + tx = <&gpioe 1 ALT8 NO_PULL PUSH_PULL LOW_SPEED>;
> + rx = <&gpioe 0 ALT8 NO_PULL>;
> + };
> + };
> + };
Can't the outer level be avoided here to save space and indentation?
> + };
> +
> + timer2: timer at 40000000 {
> + compatible = "st,stm32-timer";
> + reg = <0x40000000 0x400>;
> + interrupts = <28>;
> + resets = <&reset TIM2_RESET>;
> + clocks = <&clk_pmtr1>;
> +
> + status = "disabled";
> + };
> +
> + timer3: timer at 40000400 {
> + compatible = "st,stm32-timer";
> + reg = <0x40000400 0x400>;
> + interrupts = <29>;
> + resets = <&reset TIM3_RESET>;
> + clocks = <&clk_pmtr1>;
> +
> + status = "disabled";
> + };
> +
> + timer4: timer at 40000800 {
> + compatible = "st,stm32-timer";
> + reg = <0x40000800 0x400>;
> + interrupts = <30>;
> + resets = <&reset TIM4_RESET>;
> + clocks = <&clk_pmtr1>;
> +
> + status = "disabled";
> + };
> +
> + timer5: timer at 40000c00 {
> + compatible = "st,stm32-timer";
> + reg = <0x40000c00 0x400>;
> + interrupts = <50>;
> + resets = <&reset TIM5_RESET>;
> + clocks = <&clk_pmtr1>;
> + };
> +
> + timer6: timer at 40001000 {
> + compatible = "st,stm32-timer";
> + reg = <0x40001000 0x400>;
> + interrupts = <54>;
> + resets = <&reset TIM6_RESET>;
> + clocks = <&clk_pmtr1>;
> +
> + status = "disabled";
> + };
> +
> + timer7: timer at 40001400 {
> + compatible = "st,stm32-timer";
> + reg = <0x40001400 0x400>;
> + interrupts = <55>;
> + resets = <&reset TIM7_RESET>;
> + clocks = <&clk_pmtr1>;
> +
> + status = "disabled";
> + };
> +
> + usart1: usart at 40011000 {
> + compatible = "st,stm32-usart";
> + reg = <0x40011000 0x400>;
> + interrupts = <37>;
> + clocks = <&clk_pclk2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart2: usart at 40004400 {
> + compatible = "st,stm32-usart";
> + reg = <0x40004400 0x400>;
> + interrupts = <38>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
Copy&paste, also below. Is this really .dtsi material?
> +
> + status = "disabled";
> + };
> +
> + usart3: usart at 40004800 {
> + compatible = "st,stm32-usart";
> + reg = <0x40004800 0x400>;
> + interrupts = <39>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart4: usart at 40004c00 {
> + compatible = "st,stm32-usart";
> + reg = <0x40004c00 0x400>;
> + interrupts = <52>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart5: usart at 40005000 {
> + compatible = "st,stm32-usart";
> + reg = <0x40005000 0x400>;
> + interrupts = <53>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart6: usart at 40011400 {
> + compatible = "st,stm32-usart";
> + reg = <0x40011400 0x400>;
> + interrupts = <71>;
> + clocks = <&clk_pclk2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart7: usart at 40007800 {
Please order all nodes by unit address, not by label.
> + compatible = "st,stm32-usart";
> + reg = <0x40007800 0x400>;
> + interrupts = <82>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
> +
> + usart8: usart at 40007c00 {
> + compatible = "st,stm32-usart";
> + reg = <0x40007c00 0x400>;
> + interrupts = <83>;
> + clocks = <&clk_pclk1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1>;
> +
> + status = "disabled";
> + };
I remember two of them not being USART but UART? Similarly, two of them
support flow control (or two don't?), for which we would either need a
property or two different compatible strings.
> + };
> +};
Regards,
Andreas
--
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Jennifer Guild, Dilip Upmanyu,
Graham Norton; HRB 21284 (AG Nürnberg)
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150302/1315830b/attachment-0001.sig>
More information about the linux-arm-kernel
mailing list