[PATCH v3 4/4] power: Add an axp20x-usb-power driver
Krzysztof Kozlowski
k.kozlowski at samsung.com
Fri Jun 26 22:28:40 PDT 2015
W dniu 26.06.2015 o 19:59, Hans de Goede pisze:
> This adds a driver for the usb power_supply bits of the axp20x PMICs.
>
> I initially started writing my own driver, before coming aware of
> Bruno Prémont's excellent earlier RFC with a driver for this.
>
> My driver was lacking CURRENT_MAX and VOLTAGE_MIN support Bruno's
> drvier has, so I've copied the code for those from his driver.
>
> Note that the AC-power-supply and battery charger bits will need separate
> drivers. Each one needs its own devictree child-node so that other
> devicetree nodes can reference the right power-supply, and thus each one
> will get its own mfd-cell / platform_device and platform-driver.
>
> Cc: Bruno Prémont <bonbons at linux-vserver.org>
> Acked-by: Lee Jones <lee.jones at linaro.org>
> Signed-off-by: Bruno Prémont <bonbons at linux-vserver.org>
> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> ---
> Changes in v2:
> -Split out the dt-bindings documentation into a separate patch
> -Renamed axp20x_read_16bit to axp20x_read_variable_width
> -Use better local variable names inside axp20x_read_variable_width
> Changes in v3:
> -Add Bruno's S-o-b
Hi,
Two minor comments below, the driver itself looks good.
> ---
> drivers/power/Kconfig | 7 ++
> drivers/power/Makefile | 1 +
> drivers/power/axp20x_usb_power.c | 243 +++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 24 ++++
> 4 files changed, 275 insertions(+)
> create mode 100644 drivers/power/axp20x_usb_power.c
>
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index 4091fb0..1fee60c 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -439,6 +439,13 @@ config BATTERY_RT5033
> The fuelgauge calculates and determines the battery state of charge
> according to battery open circuit voltage.
>
> +config AXP20X_POWER
> + tristate "AXP20x power supply driver"
> + depends on MFD_AXP20X
> + help
> + This driver provides support for the power supply features of
> + AXP20x PMIC.
> +
> source "drivers/power/reset/Kconfig"
>
> endif # POWER_SUPPLY
> diff --git a/drivers/power/Makefile b/drivers/power/Makefile
> index b7b0181..ae0f27d 100644
> --- a/drivers/power/Makefile
> +++ b/drivers/power/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_GENERIC_ADC_BATTERY) += generic-adc-battery.o
>
> obj-$(CONFIG_PDA_POWER) += pda_power.o
> obj-$(CONFIG_APM_POWER) += apm_power.o
> +obj-$(CONFIG_AXP20X_POWER) += axp20x_usb_power.o
> obj-$(CONFIG_MAX8925_POWER) += max8925_power.o
> obj-$(CONFIG_WM831X_BACKUP) += wm831x_backup.o
> obj-$(CONFIG_WM831X_POWER) += wm831x_power.o
> diff --git a/drivers/power/axp20x_usb_power.c b/drivers/power/axp20x_usb_power.c
> new file mode 100644
> index 0000000..09f388e
> --- /dev/null
> +++ b/drivers/power/axp20x_usb_power.c
> @@ -0,0 +1,243 @@
> +/*
> + * AXP20x PMIC USB power supply status driver
> + *
> + * Copyright (C) 2015 Hans de Goede <hdegoede at redhat.com>
> + * Copyright (C) 2014 Bruno Prémont <bonbons at linux-vserver.org>
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + */
> +
> +#include <linux/device.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/axp20x.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +#define DRVNAME "axp20x-usb-power-supply"
> +
> +#define AXP20X_PWR_STATUS_VBUS_PRESENT BIT(5)
> +#define AXP20X_PWR_STATUS_VBUS_USED BIT(4)
> +
> +#define AXP20X_USB_STATUS_VBUS_VALID BIT(2)
> +
> +#define AXP20X_VBUS_VHOLD_uV(b) (4000000 + (((b) >> 3) & 7) * 100000)
> +#define AXP20X_VBUS_CLIMIT_MASK 3
> +#define AXP20X_VBUC_CLIMIT_900mA 0
> +#define AXP20X_VBUC_CLIMIT_500mA 1
> +#define AXP20X_VBUC_CLIMIT_100mA 2
> +#define AXP20X_VBUC_CLIMIT_NONE 3
> +
> +#define AXP20X_ADC_EN1_VBUS_CURR BIT(2)
> +#define AXP20X_ADC_EN1_VBUS_VOLT BIT(3)
> +
> +#define AXP20X_VBUS_MON_VBUS_VALID BIT(3)
> +
> +struct axp20x_usb_power {
> + struct regmap *regmap;
> + struct power_supply *supply;
> +};
> +
> +static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
> +{
> + struct axp20x_usb_power *power = devid;
> +
> + power_supply_changed(power->supply);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int axp20x_usb_power_get_property(struct power_supply *psy,
> + enum power_supply_property psp, union power_supply_propval *val)
> +{
> + struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
> + unsigned int input, v;
> + int r;
Here and in probe function - it is strictly personal but I don't like
the 'r' variable. I got used to 'err' or 'ret' which are more
descriptive to me. 'r' may look like 'resource' for example.
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_VOLTAGE_MIN:
> + r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
> + if (r)
> + return r;
> +
> + val->intval = AXP20X_VBUS_VHOLD_uV(v);
> + return 0;
> + case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + r = axp20x_read_variable_width(power->regmap,
> + AXP20X_VBUS_V_ADC_H, 12);
> + if (r < 0)
> + return r;
> +
> + val->intval = r * 1700; /* 1 step = 1.7 mV */
> + return 0;
> + case POWER_SUPPLY_PROP_CURRENT_MAX:
> + r = regmap_read(power->regmap, AXP20X_VBUS_IPSOUT_MGMT, &v);
> + if (r)
> + return r;
> +
> + switch (v & AXP20X_VBUS_CLIMIT_MASK) {
> + case AXP20X_VBUC_CLIMIT_100mA:
> + val->intval = 100000;
> + break;
> + case AXP20X_VBUC_CLIMIT_500mA:
> + val->intval = 500000;
> + break;
> + case AXP20X_VBUC_CLIMIT_900mA:
> + val->intval = 900000;
> + break;
> + case AXP20X_VBUC_CLIMIT_NONE:
> + val->intval = -1;
> + break;
> + }
> + return 0;
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + r = axp20x_read_variable_width(power->regmap,
> + AXP20X_VBUS_I_ADC_H, 12);
> + if (r < 0)
> + return r;
> +
> + val->intval = r * 375; /* 1 step = 0.375 mA */
> + return 0;
> + default:
> + break;
> + }
> +
> + /* All the properties below need the input-status reg value */
> + r = regmap_read(power->regmap, AXP20X_PWR_INPUT_STATUS, &input);
> + if (r)
> + return r;
> +
> + switch (psp) {
> + case POWER_SUPPLY_PROP_HEALTH:
> + if (!(input & AXP20X_PWR_STATUS_VBUS_PRESENT)) {
> + val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
> + break;
> + }
> +
> + r = regmap_read(power->regmap, AXP20X_USB_OTG_STATUS, &v);
> + if (r)
> + return r;
> +
> + if (!(v & AXP20X_USB_STATUS_VBUS_VALID)) {
> + val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> + break;
> + }
> +
> + val->intval = POWER_SUPPLY_HEALTH_GOOD;
> + break;
> + case POWER_SUPPLY_PROP_PRESENT:
> + val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_PRESENT);
> + break;
> + case POWER_SUPPLY_PROP_ONLINE:
> + val->intval = !!(input & AXP20X_PWR_STATUS_VBUS_USED);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static enum power_supply_property axp20x_usb_power_properties[] = {
> + POWER_SUPPLY_PROP_HEALTH,
> + POWER_SUPPLY_PROP_PRESENT,
> + POWER_SUPPLY_PROP_ONLINE,
> + POWER_SUPPLY_PROP_VOLTAGE_MIN,
> + POWER_SUPPLY_PROP_VOLTAGE_NOW,
> + POWER_SUPPLY_PROP_CURRENT_MAX,
> + POWER_SUPPLY_PROP_CURRENT_NOW,
> +};
> +
> +static const struct power_supply_desc axp20x_usb_power_desc = {
> + .name = "axp20x-usb",
> + .type = POWER_SUPPLY_TYPE_USB,
> + .properties = axp20x_usb_power_properties,
> + .num_properties = ARRAY_SIZE(axp20x_usb_power_properties),
> + .get_property = axp20x_usb_power_get_property,
> +};
> +
> +static int axp20x_usb_power_probe(struct platform_device *pdev)
> +{
> + struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
> + struct power_supply_config psy_cfg = {};
> + struct axp20x_usb_power *power;
> + static const char * const irq_names[] = { "VBUS_PLUGIN",
> + "VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID" };
> + int i, irq, r;
> +
> + if (!of_device_is_available(pdev->dev.of_node))
> + return -ENODEV;
> +
> + power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
> + if (!power)
> + return -ENOMEM;
> +
> + power->regmap = axp20x->regmap;
> +
> + /* Enable vbus valid checking */
> + r = regmap_update_bits(power->regmap, AXP20X_VBUS_MON,
> + AXP20X_VBUS_MON_VBUS_VALID, AXP20X_VBUS_MON_VBUS_VALID);
> + if (r)
> + return r;
> +
> + /* Enable vbus voltage and current measurement */
> + r = regmap_update_bits(power->regmap, AXP20X_ADC_EN1,
> + AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT,
> + AXP20X_ADC_EN1_VBUS_CURR | AXP20X_ADC_EN1_VBUS_VOLT);
> + if (r)
> + return r;
> +
> + psy_cfg.of_node = pdev->dev.of_node;
> + psy_cfg.drv_data = power;
> +
> + power->supply = devm_power_supply_register(&pdev->dev,
> + &axp20x_usb_power_desc, &psy_cfg);
> + if (IS_ERR(power->supply))
> + return PTR_ERR(power->supply);
> +
> + /* Request irqs after registering, as irqs may trigger immediately */
> + for (i = 0; i < ARRAY_SIZE(irq_names); i++) {
> + irq = platform_get_irq_byname(pdev, irq_names[i]);
> + if (irq < 0) {
> + dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
> + irq_names[i], irq);
> + continue;
> + }
> + irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
> + r = devm_request_any_context_irq(&pdev->dev, irq,
> + axp20x_usb_power_irq, 0, DRVNAME, power);
> + if (r < 0)
> + dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
> + irq_names[i], r);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id axp20x_usb_power_match[] = {
> + { .compatible = "x-powers,axp202-usb-power-supply" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
> +
> +static struct platform_driver axp20x_usb_power_driver = {
> + .probe = axp20x_usb_power_probe,
> + .driver = {
> + .name = DRVNAME,
> + .of_match_table = axp20x_usb_power_match,
> + },
> +};
> +
> +module_platform_driver(axp20x_usb_power_driver);
> +
> +MODULE_AUTHOR("Hans de Goede <hdegoede at redhat.com>");
> +MODULE_DESCRIPTION("AXP20x PMIC USB power supply status driver");
> +MODULE_LICENSE("GPL");
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 6d8b39a..8ec996e 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -11,6 +11,8 @@
> #ifndef __LINUX_MFD_AXP20X_H
> #define __LINUX_MFD_AXP20X_H
>
> +#include <linux/regmap.h>
> +
> enum {
> AXP202_ID = 0,
> AXP209_ID,
> @@ -372,4 +374,26 @@ struct axp288_extcon_pdata {
> struct gpio_desc *gpio_mux_cntl;
> };
>
> +/* generic helper function for reading 9-16 bit wide regs */
> +static inline int axp20x_read_variable_width(struct regmap *regmap,
> + unsigned int reg, unsigned int width)
> +{
> + unsigned int reg_val, result;
> + int err;
> +
> + err = regmap_read(regmap, reg, ®_val);
> + if (err)
> + return err;
> +
> + result = reg_val << (width - 8);
> +
> + err = regmap_read(regmap, reg + 1, ®_val);
> + if (err)
> + return err;
> +
> + result |= reg_val;
> +
> + return result;
> +}
> +
> #endif /* __LINUX_MFD_AXP20X_H */
Is this static inline function used outside of
drivers/power/axp20x_usb_power.c? Looks like it isn't, but maybe you
have a plan for it? If not, then it shouldn't be in header file.
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list