[PATCH v3 2/4] dt-bindings: brcmstb-gpio: document properties for wakeup
Gregory Fong
gregory.0xf0 at gmail.com
Wed Jun 17 18:00:41 PDT 2015
Some brcmstb GPIO controllers can be used to wake from suspend, so use
the de facto standard property 'wakeup-source' to mark the nodes of
controllers with that capability.
Also document interrupts-extended, which will be used for wakeup
handling because the interrupt parent for the wake IRQ is different
from the regular IRQ.
While we're at it, a few more fixes: We don't actually use the
"interrupt-names" property, so remove it from the listed optional
properties and from the examples. And since we're modifying the
examples, also follow Brian's suggestions to:
- change #gpio-cells, #interrupt-cells, and brcm,gpio-bank-widths from
hex to dec
- use phandles
Reviewed-by: Brian Norris <computersforpeace at gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0 at gmail.com>
---
v3: Update per Brian's suggestions described in above message.
.../devicetree/bindings/gpio/brcm,brcmstb-gpio.txt | 35 +++++++++++++++++-----
1 file changed, 28 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
index 435f1bc..b405b44 100644
--- a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
@@ -33,6 +33,13 @@ Optional properties:
- interrupt-parent:
phandle of the parent interrupt controller
+- interrupts-extended:
+ Alternate form of specifying interrupts and parents that allows for
+ multiple parents. This takes precedence over 'interrupts' and
+ 'interrupt-parent'. Wakeup-capable GPIO controllers often route their
+ wakeup interrupt lines through a different interrupt controller than the
+ primary interrupt line, making this property necessary.
+
- #interrupt-cells:
Should be <2>. The first cell is the GPIO number, the second should specify
flags. The following subset of flags is supported:
@@ -47,19 +54,33 @@ Optional properties:
- interrupt-controller:
Marks the device node as an interrupt controller
-- interrupt-names:
- The name of the IRQ resource used by this controller
+- wakeup-source:
+ GPIOs for this controller can be used as a wakeup source
Example:
upg_gio: gpio at f040a700 {
- #gpio-cells = <0x2>;
- #interrupt-cells = <0x2>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
gpio-controller;
interrupt-controller;
reg = <0xf040a700 0x80>;
- interrupt-parent = <0xf>;
+ interrupt-parent = <&irq0_intc>;
+ interrupts = <0x6>;
+ brcm,gpio-bank-widths = <32 32 32 24>;
+ };
+
+ upg_gio_aon: gpio at f04172c0 {
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+ gpio-controller;
+ interrupt-controller;
+ reg = <0xf04172c0 0x40>;
+ interrupt-parent = <&irq0_aon_intc>;
interrupts = <0x6>;
- interrupt-names = "upg_gio";
- brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>;
+ interrupts-extended = <&irq0_aon_intc 0x6>,
+ <&aon_pm_l2_intc 0x5>;
+ wakeup-source;
+ brcm,gpio-bank-widths = <18 4>;
};
--
1.9.1
More information about the linux-arm-kernel
mailing list