[RFC] ARM: exynos: MCPM: [is this a] fix for secondary boot on 5422?
Bartlomiej Zolnierkiewicz
b.zolnierkie at samsung.com
Mon Jun 15 03:07:23 PDT 2015
Hi,
+ Cc Przemyslaw Marczak (he is working on fixing u-boot fox XU3)
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
On Sunday, June 14, 2015 05:56:20 PM Krzysztof Kozłowski wrote:
> 2014-11-25 15:21 GMT+09:00 Kevin Hilman <khilman at kernel.org>:
> > From: Kevin Hilman <khilman at linaro.org>
> >
> > Using the current exynos_defconfig on the exynos5422-odroid-xu3, only
> > 6 of 8 CPUs come online with MCPM boot. CPU0 is an A7, CPUs 1-4 are
> > A15s and CPU5-7 are the other A7s, but with the current code, CPUs 5
> > and 7 do not boot:
> >
> > [...]
> > Exynos MCPM support installed
> > CPU1: update cpu_capacity 1535
> > CPU1: thread -1, cpu 0, socket 0, mpidr 80000000
> > CPU2: update cpu_capacity 1535
> > CPU2: thread -1, cpu 1, socket 0, mpidr 80000001
> > CPU3: update cpu_capacity 1535
> > CPU3: thread -1, cpu 2, socket 0, mpidr 80000002
> > CPU4: update cpu_capacity 1535
> > CPU4: thread -1, cpu 3, socket 0, mpidr 80000003
> > CPU5: failed to come online
> > CPU6: update cpu_capacity 448
> > CPU6: thread -1, cpu 2, socket 1, mpidr 80000102
> > CPU7: failed to come online
> > Brought up 6 CPUs
> > CPU: WARNING: CPU(s) started in wrong/inconsistent modes
> > (primary CPU mode 0x13)
> > CPU: This may indicate a broken bootloader or firmware.
> >
> > Thanks to a tip from Abhilash, this patch gets all 8 CPUs booting
> > again, but the warning about CPUs started in inconsistent modes
> > remains. Also, not being terribly familiar with Exynos internals,
> > it's not at all obvious to me why this register write (done for *all*
> > secondaries) makes things work works for the 2 secondary CPUs that
> > didn't come online. It's also not obvious whether this is the right
> > general fix, since it doesn't seem to be needed on other 542x or 5800
> > platforms.
> >
> > I suspect the "right" fix is in the bootloader someplace, but not
> > knowing this hardware well, I'm not sure if the fix is in u-boot
> > proper, or somewhere in the binary blobs (bl1/bl2/tz) that start
> > before u-boot. The u-boot I'm using is from the hardkernel u-boot
> > repo[1], and I'd welcome any suggestions to try. I'm able to rebuild
> > my own u-boot from there, but only have binaries for bl1/bl2/tz.
> >
> > [1] branch "odroidxu3-v2012.07" of: https://github.com/hardkernel/u-boot.git
> >
> >
> > Cc: Mauro Ribeiro <mauro.ribeiro at hardkernel.com>
> > Cc: Abhilash Kesavan <a.kesavan at samsung.com>,
> > Cc: Andrew Bresticker <abrestic at chromium.org>
> > Cc: Doug Anderson <dianders at chromium.org>
> > Cc: Nicolas Pitre <nicolas.pitre at linaro.org>
> > Signed-off-by: Kevin Hilman <khilman at linaro.org>
> > ---
> > arch/arm/mach-exynos/mcpm-exynos.c | 2 ++
> > arch/arm/mach-exynos/regs-pmu.h | 1 +
> > 2 files changed, 3 insertions(+)
>
> Hi,
>
> +Cc Marek, Bartlomiej, Kukjin Kim,
>
>
> I would like to bring back this topic. Unfortunately I don't have
> access to source code of BL1 (or any other firmware blob) so my
> knowledge here comes mostly from experimenting and from looking at
> sources of vendor kernel for Gear 2 (Exynos3250) and SM-G900H (Galaxy
> S5, Exynos5422).
>
> It seems that some booting firmware (I would suspect BL1 because this
> ships Samsung to Hardkernel) uses SPARE2 as synchronization mechanism.
> For example vendor kernel, when booting little core, it waits till
> SPARE2==1 and then executes software reset for this core.
>
> Observations shown that BL1 for Odroid, when booting secondary little core:
> 1. Expects that SPARE2 register will be initialized to 1.
> 2. If it is, then it sets it to 0, proceeds further and little core boots.
> 3. If it is not, then it sets it to 1 and waits. Maybe this is a
> notification to userspace - reset me please!
>
> Unfortunately executing software reset in that time (at point 3)
> stopped kernel from booting. No logs/dmesg and I was unable to turn on
> early printk.
>
> The answer why two of little cores boot is quite simple now. At
> beginning the SPARE2==0 so first little core will set it to 1 and wait
> till software reset. Kernel timeouts on this CPU bring up so it starts
> the sequence for next little core. Now the SPARE2==1 so the core boots
> fine and SPARE2 is set to 0. The last little core starts from
> SPARE2==0, sets it to 1 and waits for software reset.
>
> Since no one knows how this exactly works and we are stuck with BL1
> provided as is, then IMHO the patch makes sense.
>
> Kevin, can you refresh the patch?
> It would be nice to:
> 1. set SPARE2 only for Odroid (of_machine_is_compatible()),
> 2. extend the explanation.
>
>
> Best regards,
> Krzysztof
More information about the linux-arm-kernel
mailing list