[PATCH v3 2/2] arm64: dts: mt8173: Add I2C device node
Daniel Kurtz
djkurtz at chromium.org
Fri Jun 12 05:28:51 PDT 2015
Hi Eddie,
On Fri, Jun 12, 2015 at 5:27 PM, Eddie Huang <eddie.huang at mediatek.com> wrote:
>
> Add MT8173 I2C device nodes, include I2C controllers and pins.
> MT8173 has six I2C controllers, from i2c0 to i2c6, exclude i2c5.
> The 6th I2C controller register base doesn't next to 5th I2C,
> and there is a hardware between 5th and 6th I2C controller. So
> SoC designer name 6th controller as "i2c6", not "i2c5".
This is slightly misleading. There are in fact 7 I2C controllers, but
"i2c5" is dedicated for use by HDMI for ddc & hdcp.
Is there a reason why the HDMI I2C port cannot be controlled by the
generic i2c driver?
Of course the hdmiddc / i2c5 node can always be added in a later
patch, so this is no reason to hold up this patch.
> Signed-off-by: Eddie Huang <eddie.huang at mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 50 ++++++++++++++++++++
> arch/arm64/boot/dts/mediatek/mt8173.dtsi | 72 +++++++++++++++++++++++++++++
> 2 files changed, 122 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> index 43d5401..2e01988 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
> @@ -33,6 +33,56 @@
> chosen { };
> };
>
> +&pio {
I don't think we needed to move these i2c pinmux descriptions from
mt8173.dtsi to the board .dts file.
AFAICT, the "i2cN_pins_a" nodes defined here are the pinctl
configuration that the corresponding enabled i2c nodes would choose.
Thus, they are generic to the MT8173 SoC, not specific to any board.
By themselves, these nodes do not actually select a pin configuration.
It is the nodes that *enable* the individual i2c nodes, and hence
activate those pin settings, which is board specific.
Hence, if your intent is to have the evb enable all i2c nodes, it
would have a set of nodes like this:
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
...
> + i2c0_pins_a: i2c0 at 0 {
Do these nodes need the "@0"?
>
> + pins1 {
> + pinmux = <MT8173_PIN_45_SDA0__FUNC_SDA0>,
> + <MT8173_PIN_46_SCL0__FUNC_SCL0>;
> + bias-disable;
> + };
> + };
> +
> + i2c1_pins_a: i2c1 at 0 {
> + pins1 {
> + pinmux = <MT8173_PIN_125_SDA1__FUNC_SDA1>,
> + <MT8173_PIN_126_SCL1__FUNC_SCL1>;
> + bias-disable;
> + };
> + };
> +
> + i2c2_pins_a: i2c2 at 0 {
> + pins1 {
> + pinmux = <MT8173_PIN_43_SDA2__FUNC_SDA2>,
> + <MT8173_PIN_44_SCL2__FUNC_SCL2>;
> + bias-disable;
> + };
> + };
> +
> + i2c3_pins_a: i2c3 at 0 {
> + pins1 {
> + pinmux = <MT8173_PIN_106_SDA3__FUNC_SDA3>,
> + <MT8173_PIN_107_SCL3__FUNC_SCL3>;
> + bias-disable;
> + };
> + };
> +
> + i2c4_pins_a: i2c4 at 0 {
> + pins1 {
> + pinmux = <MT8173_PIN_133_SDA4__FUNC_SDA4>,
> + <MT8173_PIN_134_SCL4__FUNC_SCL4>;
> + bias-disable;
> + };
> + };
> +
> + i2c6_pins_a: i2c6 at 0 {
> + pins1 {
> + pinmux = <MT8173_PIN_100_MSDC2_DAT0__FUNC_SDA5>,
> + <MT8173_PIN_101_MSDC2_DAT1__FUNC_SCL5>;
These are the SDA/SCL pins for i2c port 6, so they should really be
_SDA6 / _SCL6.
However... I checked, and these settings are labeled "SDA5 & SCL5" in
the datasheet.
I recommend marking them correctly as 6 here and fixing the datasheet :-).
>
> + bias-disable;
> + };
> + };
> +};
> +
> &uart0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> index b52ec43..6d3dbbdd 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> @@ -229,6 +229,78 @@
> clocks = <&uart_clk>;
> status = "disabled";
> };
> +
> + i2c0: i2c at 11007000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11007000 0 0x70>,
> + <0 0x11000100 0 0x80>;
> + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C0>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
The following fields must also be selected by the i2c nodes when they
are enabled:
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
#address-cells = <1>;
#size-cells = <0>;
So, is there any reason not to also include them here in mt8173.dtsi
so we can use them as defaults?
This would simplify the i2c nodes in the board specific .dts files.
The only field that might be board specific would be clock-frequency,
but that is trivial to override on a port-by-port basis in board files
as necessary.
Thanks,
-Dan
>
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 11008000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11008000 0 0x70>,
> + <0 0x11000180 0 0x80>;
> + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C1>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 11009000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11009000 0 0x70>,
> + <0 0x11000200 0 0x80>;
> + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C2>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
> + status = "disabled";
> + };
> +
> + i2c3: i2c3 at 11010000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11010000 0 0x70>,
> + <0 0x11000280 0 0x80>;
> + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C3>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
> + status = "disabled";
> + };
> +
> + i2c4: i2c4 at 11011000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11011000 0 0x70>,
> + <0 0x11000300 0 0x80>;
> + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C4>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
> + status = "disabled";
> + };
> +
> + i2c6: i2c6 at 11013000 {
> + compatible = "mediatek,mt8173-i2c";
> + reg = <0 0x11013000 0 0x70>,
> + <0 0x11000080 0 0x80>;
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>;
> + clock-div = <16>;
> + clocks = <&pericfg CLK_PERI_I2C6>,
> + <&pericfg CLK_PERI_AP_DMA>;
> + clock-names = "main", "dma";
> + status = "disabled";
> + };
> };
>
> };
> --
> 1.8.1.1.dirty
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
More information about the linux-arm-kernel
mailing list