[PATCH v4 1/2] phy-sun4i-usb: Add full support for usb0 phy / OTG
Kishon Vijay Abraham I
kishon at ti.com
Wed Jun 10 22:48:18 PDT 2015
+Chanwoo
Hi,
On Sunday 31 May 2015 09:40 PM, Hans de Goede wrote:
> The usb0 phy is connected to an OTG controller, and as such needs some special
> handling:
>
> 1) It allows explicit control over the pullups, enable these on phy_init and
> disable them on phy_exit.
>
> 2) It has bits to signal id and vbus detect to the musb-core, add support for
> for monitoring id and vbus detect gpio-s for use in dual role mode, and set
> these bits to the correct values for operating in host only mode when no
> gpios are specified in the devicetree.
>
> 3) When in dual role mode the musb sunxi glue needs to know if the a host or
> device cable is plugged in, so when in dual role mode register an extcon.
>
> While updating the devicetree binding documentation also add documentation
> for the sofar undocumented usage of regulators for vbus for all 3 phys.
>
> Signed-off-by: Hans de Goede <hdegoede at redhat.com>
> ---
> Changes in v2:
> -Removed the sunxi specific phy functions, instead the id / vbus gpio polling
> has been moved to the phy-sun4i-usb driver and their status is exported
> through extcon for the sunxi-musb glue
> Changes in v3:
> -No changes
> Changes in v4:
> -Do not call regulator_disable in an unbalanced manner when an external vbus
> is present
> ---
> .../devicetree/bindings/phy/sun4i-usb-phy.txt | 18 +-
> drivers/phy/Kconfig | 1 +
> drivers/phy/phy-sun4i-usb.c | 273 ++++++++++++++++++++-
> 3 files changed, 281 insertions(+), 11 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> index 16528b9..557fa99 100644
> --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> @@ -23,6 +23,13 @@ Required properties:
> * "usb1_reset"
> * "usb2_reset" for sun4i, sun6i or sun7i
>
> +Optional properties:
> +- usb0_id_det-gpios : gpio phandle for reading the otg id pin value
> +- usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus
> +- usb0_vbus-supply : regulator phandle for controller usb0 vbus
> +- usb1_vbus-supply : regulator phandle for controller usb1 vbus
> +- usb2_vbus-supply : regulator phandle for controller usb2 vbus
> +
> Example:
> usbphy: phy at 0x01c13400 {
> #phy-cells = <1>;
> @@ -32,6 +39,13 @@ Example:
> reg-names = "phy_ctrl", "pmu1", "pmu2";
> clocks = <&usb_clk 8>;
> clock-names = "usb_phy";
> - resets = <&usb_clk 1>, <&usb_clk 2>;
> - reset-names = "usb1_reset", "usb2_reset";
> + resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
> + reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
> + usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
> + usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
> + usb0_vbus-supply = <®_usb0_vbus>;
> + usb1_vbus-supply = <®_usb1_vbus>;
> + usb2_vbus-supply = <®_usb2_vbus>;
> };
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index a53bd5b..4614fba 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -173,6 +173,7 @@ config PHY_SUN4I_USB
> tristate "Allwinner sunxi SoC USB PHY driver"
> depends on ARCH_SUNXI && HAS_IOMEM && OF
> depends on RESET_CONTROLLER
> + select EXTCON
Avoid using 'select' on visible Kconfig symbols.
Also please split the patch to make the reviewing a bit easier.
Thanks
Kishon
> select GENERIC_PHY
> help
> Enable this to support the transceiver that is part of Allwinner
> diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/phy-sun4i-usb.c
> index 91c5be4..b45d707 100644
> --- a/drivers/phy/phy-sun4i-usb.c
> +++ b/drivers/phy/phy-sun4i-usb.c
> @@ -1,7 +1,7 @@
> /*
> * Allwinner sun4i USB phy driver
> *
> - * Copyright (C) 2014 Hans de Goede <hdegoede at redhat.com>
> + * Copyright (C) 2014-2015 Hans de Goede <hdegoede at redhat.com>
> *
> * Based on code from
> * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
> @@ -23,17 +23,23 @@
>
> #include <linux/clk.h>
> #include <linux/err.h>
> +#include <linux/extcon.h>
> #include <linux/io.h>
> +#include <linux/interrupt.h>
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/mutex.h>
> #include <linux/of.h>
> #include <linux/of_address.h>
> +#include <linux/of_gpio.h>
> #include <linux/phy/phy.h>
> #include <linux/phy/phy-sun4i-usb.h>
> #include <linux/platform_device.h>
> #include <linux/regulator/consumer.h>
> #include <linux/reset.h>
> +#include <linux/workqueue.h>
> +
> +#define DRIVER_NAME "sun4i-usb-phy"
>
> #define REG_ISCR 0x00
> #define REG_PHYCTL 0x04
> @@ -47,6 +53,17 @@
> #define SUNXI_AHB_INCRX_ALIGN_EN BIT(8)
> #define SUNXI_ULPI_BYPASS_EN BIT(0)
>
> +/* ISCR, Interface Status and Control bits */
> +#define ISCR_ID_PULLUP_EN (1 << 17)
> +#define ISCR_DPDM_PULLUP_EN (1 << 16)
> +/* sunxi has the phy id/vbus pins not connected, so we use the force bits */
> +#define ISCR_FORCE_ID_MASK (3 << 14)
> +#define ISCR_FORCE_ID_LOW (2 << 14)
> +#define ISCR_FORCE_ID_HIGH (3 << 14)
> +#define ISCR_FORCE_VBUS_MASK (3 << 12)
> +#define ISCR_FORCE_VBUS_LOW (2 << 12)
> +#define ISCR_FORCE_VBUS_HIGH (3 << 12)
> +
> /* Common Control Bits for Both PHYs */
> #define PHY_PLL_BW 0x03
> #define PHY_RES45_CAL_EN 0x0c
> @@ -63,6 +80,13 @@
>
> #define MAX_PHYS 3
>
> +/*
> + * Note do not raise the debounce time, we must report Vusb high within 100ms
> + * otherwise we get Vbus errors
> + */
> +#define DEBOUNCE_TIME msecs_to_jiffies(50)
> +#define POLL_TIME msecs_to_jiffies(250)
> +
> struct sun4i_usb_phy_data {
> void __iomem *base;
> struct mutex mutex;
> @@ -74,13 +98,58 @@ struct sun4i_usb_phy_data {
> struct regulator *vbus;
> struct reset_control *reset;
> struct clk *clk;
> + bool regulator_on;
> int index;
> } phys[MAX_PHYS];
> + /* phy0 / otg related variables */
> + struct extcon_dev extcon;
> + const char *extcon_cable_names[3];
> + bool phy0_init;
> + bool phy0_poll;
> + struct gpio_desc *id_det_gpio;
> + struct gpio_desc *vbus_det_gpio;
> + int id_det_irq;
> + int vbus_det_irq;
> + int id_det;
> + int vbus_det;
> + struct delayed_work detect;
> };
>
> #define to_sun4i_usb_phy_data(phy) \
> container_of((phy), struct sun4i_usb_phy_data, phys[(phy)->index])
>
> +static void sun4i_usb_phy0_update_iscr(struct phy *_phy, u32 clr, u32 set)
> +{
> + struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
> + struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
> + u32 iscr;
> +
> + iscr = readl(data->base + REG_ISCR);
> + iscr &= ~clr;
> + iscr |= set;
> + writel(iscr, data->base + REG_ISCR);
> +}
> +
> +static void sun4i_usb_phy0_set_id_detect(struct phy *phy, u32 val)
> +{
> + if (val)
> + val = ISCR_FORCE_ID_HIGH;
> + else
> + val = ISCR_FORCE_ID_LOW;
> +
> + sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_ID_MASK, val);
> +}
> +
> +static void sun4i_usb_phy0_set_vbus_detect(struct phy *phy, u32 val)
> +{
> + if (val)
> + val = ISCR_FORCE_VBUS_HIGH;
> + else
> + val = ISCR_FORCE_VBUS_LOW;
> +
> + sun4i_usb_phy0_update_iscr(phy, ISCR_FORCE_VBUS_MASK, val);
> +}
> +
> static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data,
> int len)
> {
> @@ -171,12 +240,39 @@ static int sun4i_usb_phy_init(struct phy *_phy)
>
> sun4i_usb_phy_passby(phy, 1);
>
> + if (phy->index == 0) {
> + data->phy0_init = true;
> +
> + /* Enable pull-ups */
> + sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_DPDM_PULLUP_EN);
> + sun4i_usb_phy0_update_iscr(_phy, 0, ISCR_ID_PULLUP_EN);
> +
> + if (data->id_det_gpio) {
> + /* OTG mode, force ISCR and cable state updates */
> + data->id_det = -1;
> + data->vbus_det = -1;
> + queue_delayed_work(system_wq, &data->detect, 0);
> + } else {
> + /* Host only mode */
> + sun4i_usb_phy0_set_id_detect(_phy, 0);
> + sun4i_usb_phy0_set_vbus_detect(_phy, 1);
> + }
> + }
> +
> return 0;
> }
>
> static int sun4i_usb_phy_exit(struct phy *_phy)
> {
> struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
> + struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
> +
> + if (phy->index == 0) {
> + /* Disable pull-ups */
> + sun4i_usb_phy0_update_iscr(_phy, ISCR_DPDM_PULLUP_EN, 0);
> + sun4i_usb_phy0_update_iscr(_phy, ISCR_ID_PULLUP_EN, 0);
> + data->phy0_init = false;
> + }
>
> sun4i_usb_phy_passby(phy, 0);
> reset_control_assert(phy->reset);
> @@ -188,20 +284,46 @@ static int sun4i_usb_phy_exit(struct phy *_phy)
> static int sun4i_usb_phy_power_on(struct phy *_phy)
> {
> struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
> - int ret = 0;
> + struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
> + int ret;
> +
> + if (!phy->vbus || phy->regulator_on)
> + return 0;
> +
> + /* For phy0 only turn on Vbus if we don't have an ext. Vbus */
> + if (phy->index == 0 && data->vbus_det)
> + return 0;
>
> - if (phy->vbus)
> - ret = regulator_enable(phy->vbus);
> + ret = regulator_enable(phy->vbus);
> + if (ret)
> + return ret;
>
> - return ret;
> + phy->regulator_on = true;
> +
> + /* We must report Vbus high within OTG_TIME_A_WAIT_VRISE msec. */
> + if (phy->index == 0 && data->phy0_poll)
> + mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME);
> +
> + return 0;
> }
>
> static int sun4i_usb_phy_power_off(struct phy *_phy)
> {
> struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
> + struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
> +
> + if (!phy->vbus || !phy->regulator_on)
> + return 0;
>
> - if (phy->vbus)
> - regulator_disable(phy->vbus);
> + regulator_disable(phy->vbus);
> + phy->regulator_on = false;
> +
> + /*
> + * phy0 vbus typically slowly discharges, sometimes this causes the
> + * Vbus gpio to not trigger an edge irq on Vbus off, so force a rescan.
> + */
> + if (phy->index == 0 && !data->phy0_poll)
> + mod_delayed_work(system_wq, &data->detect, POLL_TIME);
>
> return 0;
> }
> @@ -221,6 +343,61 @@ static struct phy_ops sun4i_usb_phy_ops = {
> .owner = THIS_MODULE,
> };
>
> +static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work)
> +{
> + struct sun4i_usb_phy_data *data =
> + container_of(work, struct sun4i_usb_phy_data, detect.work);
> + struct phy *phy0 = data->phys[0].phy;
> + int id_det, vbus_det, id_notify = 0, vbus_notify = 0;
> +
> + id_det = gpiod_get_value_cansleep(data->id_det_gpio);
> + vbus_det = gpiod_get_value_cansleep(data->vbus_det_gpio);
> +
> + mutex_lock(&phy0->mutex);
> +
> + if (!data->phy0_init) {
> + mutex_unlock(&phy0->mutex);
> + return;
> + }
> +
> + if (id_det != data->id_det) {
> + sun4i_usb_phy0_set_id_detect(phy0, id_det);
> + data->id_det = id_det;
> + id_notify = 1;
> + }
> +
> + if (vbus_det != data->vbus_det) {
> + sun4i_usb_phy0_set_vbus_detect(phy0, vbus_det);
> + data->vbus_det = vbus_det;
> + vbus_notify = 1;
> + }
> +
> + mutex_unlock(&phy0->mutex);
> +
> + if (id_notify)
> + extcon_set_cable_state(&data->extcon,
> + extcon_cable_name[EXTCON_USB_HOST],
> + !id_det);
> +
> + if (vbus_notify)
> + extcon_set_cable_state(&data->extcon,
> + extcon_cable_name[EXTCON_USB],
> + vbus_det);
> +
> + if (data->phy0_poll)
> + queue_delayed_work(system_wq, &data->detect, POLL_TIME);
> +}
> +
> +static irqreturn_t sun4i_usb_phy0_id_vbus_det_irq(int irq, void *dev_id)
> +{
> + struct sun4i_usb_phy_data *data = dev_id;
> +
> + /* vbus or id changed, let the pins settle and then scan them */
> + mod_delayed_work(system_wq, &data->detect, DEBOUNCE_TIME);
> +
> + return IRQ_HANDLED;
> +}
> +
> static struct phy *sun4i_usb_phy_xlate(struct device *dev,
> struct of_phandle_args *args)
> {
> @@ -240,13 +417,20 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
> struct phy_provider *phy_provider;
> bool dedicated_clocks;
> struct resource *res;
> - int i;
> + int i, ret;
>
> data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> if (!data)
> return -ENOMEM;
>
> mutex_init(&data->mutex);
> + INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan);
> + data->extcon_cable_names[0] = extcon_cable_name[EXTCON_USB_HOST];
> + data->extcon_cable_names[1] = extcon_cable_name[EXTCON_USB];
> + data->extcon_cable_names[2] = NULL;
> + data->extcon.name = DRIVER_NAME;
> + data->extcon.supported_cable = data->extcon_cable_names;
> + data->extcon.dev.parent = dev;
>
> if (of_device_is_compatible(np, "allwinner,sun5i-a13-usb-phy"))
> data->num_phys = 2;
> @@ -269,6 +453,34 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
> if (IS_ERR(data->base))
> return PTR_ERR(data->base);
>
> + data->id_det_gpio = devm_gpiod_get(dev, "usb0_id_det", GPIOD_IN);
> + if (IS_ERR(data->id_det_gpio)) {
> + if (PTR_ERR(data->id_det_gpio) == -EPROBE_DEFER)
> + return -EPROBE_DEFER;
> + data->id_det_gpio = NULL;
> + }
> +
> + data->vbus_det_gpio = devm_gpiod_get(dev, "usb0_vbus_det", GPIOD_IN);
> + if (IS_ERR(data->vbus_det_gpio)) {
> + if (PTR_ERR(data->vbus_det_gpio) == -EPROBE_DEFER)
> + return -EPROBE_DEFER;
> + data->vbus_det_gpio = NULL;
> + }
> +
> + /* We either want both gpio pins or neither (when in host mode) */
> + if (!data->id_det_gpio != !data->vbus_det_gpio) {
> + dev_err(dev, "failed to get id or vbus detect pin\n");
> + return -ENODEV;
> + }
> +
> + if (data->id_det_gpio) {
> + ret = devm_extcon_dev_register(dev, &data->extcon);
> + if (ret) {
> + dev_err(dev, "failed to register extcon: %d\n", ret);
> + return ret;
> + }
> + }
> +
> for (i = 0; i < data->num_phys; i++) {
> struct sun4i_usb_phy *phy = data->phys + i;
> char name[16];
> @@ -318,12 +530,54 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
> phy_set_drvdata(phy->phy, &data->phys[i]);
> }
>
> + data->id_det_irq = gpiod_to_irq(data->id_det_gpio);
> + data->vbus_det_irq = gpiod_to_irq(data->vbus_det_gpio);
> + if (data->id_det_irq < 0 || data->vbus_det_irq < 0)
> + data->phy0_poll = true;
> +
> + if (data->id_det_irq >= 0) {
> + ret = devm_request_irq(dev, data->id_det_irq,
> + sun4i_usb_phy0_id_vbus_det_irq,
> + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
> + "usb0-id-det", data);
> + if (ret) {
> + dev_err(dev, "Err requesting id-det-irq: %d\n", ret);
> + return ret;
> + }
> + }
> +
> + if (data->vbus_det_irq >= 0) {
> + ret = devm_request_irq(dev, data->vbus_det_irq,
> + sun4i_usb_phy0_id_vbus_det_irq,
> + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
> + "usb0-vbus-det", data);
> + if (ret) {
> + dev_err(dev, "Err requesting vbus-det-irq: %d\n", ret);
> + return ret;
> + }
> + }
> +
> dev_set_drvdata(dev, data);
> phy_provider = devm_of_phy_provider_register(dev, sun4i_usb_phy_xlate);
>
> return PTR_ERR_OR_ZERO(phy_provider);
> }
>
> +static int sun4i_usb_phy_remove(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct sun4i_usb_phy_data *data = dev_get_drvdata(dev);
> +
> + if (data->id_det_irq >= 0)
> + devm_free_irq(dev, data->id_det_irq, data);
> + if (data->vbus_det_irq >= 0)
> + devm_free_irq(dev, data->vbus_det_irq, data);
> +
> + cancel_delayed_work_sync(&data->detect);
> +
> + return 0;
> +}
> +
> static const struct of_device_id sun4i_usb_phy_of_match[] = {
> { .compatible = "allwinner,sun4i-a10-usb-phy" },
> { .compatible = "allwinner,sun5i-a13-usb-phy" },
> @@ -335,9 +589,10 @@ MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
>
> static struct platform_driver sun4i_usb_phy_driver = {
> .probe = sun4i_usb_phy_probe,
> + .remove = sun4i_usb_phy_remove,
> .driver = {
> .of_match_table = sun4i_usb_phy_of_match,
> - .name = "sun4i-usb-phy",
> + .name = DRIVER_NAME,
> }
> };
> module_platform_driver(sun4i_usb_phy_driver);
>
More information about the linux-arm-kernel
mailing list