[PATCH] ARM: dts: AM35xx: fix system control module clocks

[Jeroen Hofstee]

Hello Paul,

On 05-06-15 10:04, Jeroen Hofstee wrote:
>
> On 05-06-15 10:01, Jeroen Hofstee wrote:
>>
>> On 01-06-15 19:44, Paul Walmsley wrote:
>>> The best way to make this work IMHO would be for us not to accept 
>>> any new
>>> feature addition patches as long as there are warnings reported in the
>>> test results.  The only real exception that I would foresee is if those
>>> warnings are due to something outside of our control, e.g., a crappy
>>> bootloader, as I suspect the USB_OTG initiator warnings are for the
>>> CM-T3517.
>>>
>>
>> I doubt this is related to the bootloader. I have the suspicion that 
>> is actually
>> a bug in linux but only triggered depending on whether the ROMcode setup
>> the USB OTG or not. Here is some data to backup my statement:
>>

Turns out my suspicion was wrong. This is what I know at the moment,
depending on the bootpins, u-boot will trigger a bad access when loading
a file over ethernet, but only the first time. Clearing the pending 
interrupt
before booting linux make the "USB_OTG address hole seen" go away.

Regards,
Jeroen

U-Boot 2015.04-00098-g487ee34-dirty (Jun 05 2015 - 13:14:48)

AM35XX-GP ES2.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz
ccgx + LPDDR/NAND
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   OMAP SD/MMC: 0
In:    serial
Out:   serial
Err:   serial
Die ID #2276000100000000014e0fb21500b024
Net: DaVinci-EMAC
Hit any key to stop autoboot:  0
ccgx=> echo $clear_l3_int
mw 68004428 0x11000000; mw 6800442C 0x00000000; mw 68004458 0xFFFFFFFF; 
mw 6800445C 0xFFFFFFFF
ccgx=> md 0x68000510 2
68000510: 00000000 00000000                      ........
ccgx=> tftp ccgx/zImage; tftp 80000000 ccgx/am3517-ccgx.dtb;
Using DaVinci-EMAC device
TFTP from server 10.0.0.103; our IP address is 10.0.0.250
Filename 'ccgx/zImage'.
Load address: 0x80300000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
          ##########
          863.3 KiB/s
done
Bytes transferred = 4040072 (3da588 hex)
Using DaVinci-EMAC device
TFTP from server 10.0.0.103; our IP address is 10.0.0.250
Filename 'ccgx/am3517-ccgx.dtb'.
Load address: 0x80000000
Loading: ###########
          825.2 KiB/s
done
Bytes transferred = 54112 (d360 hex)
ccgx=> md 0x68000510 2
68000510: 04000000 00000000                      ........
ccgx=> run clear_l3_int
ccgx=> md 0x68000510 2
68000510: 00000000 00000000                      ........
ccgx=> boot

# USB_OTG error is gone...