[PATCH 08/12] ARM: dts: Add minimal dm814x support
Tony Lindgren
tony at atomide.com
Wed Jun 3 09:23:17 PDT 2015
Add minimal dm814x support.
Cc: Matthijs van Duin <matthijsvanduin at gmail.com>
Signed-off-by: Tony Lindgren <tony at atomide.com>
---
arch/arm/boot/dts/dm814x.dtsi | 331 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 331 insertions(+)
create mode 100644 arch/arm/boot/dts/dm814x.dtsi
diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi
new file mode 100644
index 0000000..f3077e3
--- /dev/null
+++ b/arch/arm/boot/dts/dm814x.dtsi
@@ -0,0 +1,331 @@
+/*
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/omap.h>
+
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "ti,dm814";
+ interrupt-parent = <&intc>;
+
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cpu at 0 {
+ compatible = "arm,cortex-a8";
+ device_type = "cpu";
+ reg = <0>;
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ };
+
+ /*
+ * The soc node represents the soc top level view. It is used for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+ */
+ soc {
+ compatible = "ti,omap-infra";
+ mpu {
+ compatible = "ti,omap3-mpu";
+ ti,hwmods = "mpu";
+ };
+ };
+
+ ocp {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "l3_main";
+
+ /*
+ * See TRM "Table 1-317. L4LS Instance Summary", just deduct
+ * 0x1000 from the 1-317 addresses to get the device address
+ */
+ l4ls: l4ls at 48000000 {
+ compatible = "ti,dm814-l4ls", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x48000000 0x2000000>;
+
+ i2c1: i2c at 28000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ reg = <0x28000 0x1000>;
+ interrupts = <70>;
+ };
+
+ elm: elm at 80000 {
+ compatible = "ti,814-elm";
+ ti,hwmods = "elm";
+ reg = <0x80000 0x2000>;
+ interrupts = <4>;
+ };
+
+ gpio1: gpio at 32000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio1";
+ ti,gpio-always-on;
+ reg = <0x32000 0x2000>;
+ interrupts = <96>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio at 4c000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio2";
+ ti,gpio-always-on;
+ reg = <0x4c000 0x2000>;
+ interrupts = <98>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ i2c2: i2c at 2a000 {
+ compatible = "ti,omap4-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c2";
+ reg = <0x2a000 0x1000>;
+ interrupts = <71>;
+ };
+
+ mcspi1: spi at 30000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x30000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <65>;
+ ti,spi-num-cs = <4>;
+ ti,hwmods = "mcspi1";
+ dmas = <&edma 16 &edma 17
+ &edma 18 &edma 19>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ timer1: timer at 2e000 {
+ compatible = "ti,dm814-timer";
+ reg = <0x2e000 0x2000>;
+ interrupts = <67>;
+ ti,hwmods = "timer1";
+ ti,timer-alwon;
+ };
+
+ uart1: uart at 20000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart1";
+ reg = <0x20000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <72>;
+ dmas = <&edma 26 &edma 27>;
+ dma-names = "tx", "rx";
+ };
+
+ uart2: uart at 22000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart2";
+ reg = <0x22000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <73>;
+ dmas = <&edma 28 &edma 29>;
+ dma-names = "tx", "rx";
+ };
+
+ uart3: uart at 24000 {
+ compatible = "ti,omap3-uart";
+ ti,hwmods = "uart3";
+ reg = <0x24000 0x2000>;
+ clock-frequency = <48000000>;
+ interrupts = <74>;
+ dmas = <&edma 30 &edma 31>;
+ dma-names = "tx", "rx";
+ };
+
+ timer2: timer at 40000 {
+ compatible = "ti,dm814-timer";
+ reg = <0x40000 0x2000>;
+ interrupts = <68>;
+ ti,hwmods = "timer2";
+ };
+
+ timer3: timer at 42000 {
+ compatible = "ti,dm814-timer";
+ reg = <0x42000 0x2000>;
+ interrupts = <69>;
+ ti,hwmods = "timer3";
+ };
+
+ control: control at 160000 {
+ compatible = "ti,dm814-scm", "simple-bus";
+ reg = <0x160000 0x16d000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x160000 0x16d000>;
+
+ scm_conf: scm_conf at 0 {
+ compatible = "syscon";
+ reg = <0x0 0x800>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ scm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ scm_clockdomains: clockdomains {
+ };
+ };
+
+ pincntl: pinmux at 800 {
+ compatible = "pinctrl-single";
+ reg = <0x800 0xc38>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x300ff>;
+ };
+ };
+
+ prcm: prcm at 180000 {
+ compatible = "ti,dm814-prcm", "simple-bus";
+ reg = <0x180000 0x4000>;
+
+ prcm_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ prcm_clockdomains: clockdomains {
+ };
+ };
+
+ pllss: pllss at 1c5000 {
+ compatible = "ti,dm814-pllss", "simple-bus";
+ reg = <0x1c5000 0x2000>;
+
+ pllss_clocks: clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pllss_clockdomains: clockdomains {
+ };
+ };
+
+ wdt1: wdt at 1c7000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer";
+ reg = <0x1c7000 0x1000>;
+ interrupts = <91>;
+ };
+ };
+
+ intc: interrupt-controller at 48200000 {
+ compatible = "ti,dm814-intc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x48200000 0x1000>;
+ };
+
+ edma: edma at 49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x40>;
+ interrupts = <12 13 14>;
+ #dma-cells = <1>;
+ };
+
+ /* See TRM "Table 1-318. L4HS Instance Summary" */
+ l4hs: l4hs at 4a000000 {
+ compatible = "ti,dm814-l4hs", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x4a000000 0x1b4040>;
+ };
+
+ /* REVISIT: Move to live under l4hs once driver is fixed */
+ mac: ethernet at 4a100000 {
+ compatible = "ti,cpsw";
+ ti,hwmods = "cpgmac0";
+ clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
+ clock-names = "fck", "cpts";
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ reg = <0x4a100000 0x800
+ 0x4a100900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ /*
+ * c0_rx_thresh_pend
+ * c0_rx_pend
+ * c0_tx_pend
+ * c0_misc_pend
+ */
+ interrupts = <40 41 42 43>;
+ ranges;
+ syscon = <&scm_conf>;
+
+ davinci_mdio: mdio at 4a100800 {
+ compatible = "ti,davinci_mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ reg = <0x4a100800 0x100>;
+ };
+
+ cpsw_emac0: slave at 4a100200 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ cpsw_emac1: slave at 4a100300 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ phy_sel: cpsw-phy-sel at 0x48160650 {
+ compatible = "ti,am3352-cpsw-phy-sel";
+ reg= <0x48160650 0x4>;
+ reg-names = "gmii-sel";
+ };
+ };
+ };
+};
--
2.1.4
More information about the linux-arm-kernel
mailing list