[PATCH V9 12/14] drm/bridge: Add i2c based driver for ps8622/ps8625 bridge

Ajay kumar ajaynumb at gmail.com
Thu Jan 29 06:42:20 PST 2015


Hi Thierry,

I think you forgot to take this patch!
Can you check this?

Regards,
Ajay Kumar


On Tue, Jan 20, 2015 at 10:08 PM, Ajay Kumar <ajaykumar.rs at samsung.com> wrote:
> From: Vincent Palatin <vpalatin at chromium.org>
>
> This patch adds drm_bridge driver for parade DisplayPort
> to LVDS bridge chip.
>
> Signed-off-by: Vincent Palatin <vpalatin at chromium.org>
> Signed-off-by: Andrew Bresticker <abrestic at chromium.org>
> Signed-off-by: Sean Paul <seanpaul at chromium.org>
> Signed-off-by: Rahul Sharma <rahul.sharma at samsung.com>
> Signed-off-by: Ajay Kumar <ajaykumar.rs at samsung.com>
> Acked-by: Inki Dae <inki.dae at samsung.com>
> Tested-by: Rahul Sharma <rahul.sharma at samsung.com>
> Tested-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
> Tested-by: Gustavo Padovan <gustavo.padovan at collabora.co.uk>
> Tested-by: Sjoerd Simons <sjoerd.simons at collabora.co.uk>
> ---
>  drivers/gpu/drm/bridge/Kconfig  |    9 +
>  drivers/gpu/drm/bridge/Makefile |    1 +
>  drivers/gpu/drm/bridge/ps8622.c |  684 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 694 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/ps8622.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index 8b426e2..d06eda3 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -6,3 +6,12 @@ config DRM_PTN3460
>         select DRM_PANEL
>         ---help---
>           ptn3460 eDP-LVDS bridge chip driver.
> +
> +config DRM_PS8622
> +       tristate "Parade eDP/LVDS bridge"
> +       depends on OF && I2C
> +       select DRM_PANEL
> +       select BACKLIGHT_LCD_SUPPORT
> +       select BACKLIGHT_CLASS_DEVICE
> +       ---help---
> +         parade eDP-LVDS bridge chip driver.
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index b4733e1..105da3e 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -1,3 +1,4 @@
>  ccflags-y := -Iinclude/drm
>
> +obj-$(CONFIG_DRM_PS8622) += ps8622.o
>  obj-$(CONFIG_DRM_PTN3460) += ptn3460.o
> diff --git a/drivers/gpu/drm/bridge/ps8622.c b/drivers/gpu/drm/bridge/ps8622.c
> new file mode 100644
> index 0000000..5474a39
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ps8622.c
> @@ -0,0 +1,684 @@
> +/*
> + * Parade PS8622 eDP/LVDS bridge driver
> + *
> + * Copyright (C) 2014 Google, Inc.
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/fb.h>
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_graph.h>
> +#include <linux/pm.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <drm/drm_panel.h>
> +
> +#include "drmP.h"
> +#include "drm_crtc.h"
> +#include "drm_crtc_helper.h"
> +
> +/* Brightness scale on the Parade chip */
> +#define PS8622_MAX_BRIGHTNESS 0xff
> +
> +/* Timings taken from the version 1.7 datasheet for the PS8622/PS8625 */
> +#define PS8622_POWER_RISE_T1_MIN_US 10
> +#define PS8622_POWER_RISE_T1_MAX_US 10000
> +#define PS8622_RST_HIGH_T2_MIN_US 3000
> +#define PS8622_RST_HIGH_T2_MAX_US 30000
> +#define PS8622_PWMO_END_T12_MS 200
> +#define PS8622_POWER_FALL_T16_MAX_US 10000
> +#define PS8622_POWER_OFF_T17_MS 500
> +
> +#if ((PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US) > \
> +       (PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US))
> +#error "T2.min + T1.max must be less than T2.max + T1.min"
> +#endif
> +
> +struct ps8622_bridge {
> +       struct drm_connector connector;
> +       struct i2c_client *client;
> +       struct drm_bridge bridge;
> +       struct drm_panel *panel;
> +       struct regulator *v12;
> +       struct backlight_device *bl;
> +
> +       struct gpio_desc *gpio_slp;
> +       struct gpio_desc *gpio_rst;
> +
> +       u32 max_lane_count;
> +       u32 lane_count;
> +
> +       bool enabled;
> +};
> +
> +static inline struct ps8622_bridge *
> +               bridge_to_ps8622(struct drm_bridge *bridge)
> +{
> +       return container_of(bridge, struct ps8622_bridge, bridge);
> +}
> +
> +static inline struct ps8622_bridge *
> +               connector_to_ps8622(struct drm_connector *connector)
> +{
> +       return container_of(connector, struct ps8622_bridge, connector);
> +}
> +
> +static int ps8622_set(struct i2c_client *client, u8 page, u8 reg, u8 val)
> +{
> +       int ret;
> +       struct i2c_adapter *adap = client->adapter;
> +       struct i2c_msg msg;
> +       u8 data[] = {reg, val};
> +
> +       msg.addr = client->addr + page;
> +       msg.flags = 0;
> +       msg.len = sizeof(data);
> +       msg.buf = data;
> +
> +       ret = i2c_transfer(adap, &msg, 1);
> +       if (ret != 1)
> +               pr_warn("PS8622 I2C write (0x%02x,0x%02x,0x%02x) failed: %d\n",
> +                       client->addr + page, reg, val, ret);
> +       return !(ret == 1);
> +}
> +
> +static int ps8622_send_config(struct ps8622_bridge *ps8622)
> +{
> +       struct i2c_client *cl = ps8622->client;
> +       int err = 0;
> +
> +       /* HPD low */
> +       err = ps8622_set(cl, 0x02, 0xa1, 0x01);
> +       if (err)
> +               goto error;
> +
> +       /* SW setting: [1:0] SW output 1.2V voltage is lower to 96% */
> +       err = ps8622_set(cl, 0x04, 0x14, 0x01);
> +       if (err)
> +               goto error;
> +
> +       /* RCO SS setting: [5:4] = b01 0.5%, b10 1%, b11 1.5% */
> +       err = ps8622_set(cl, 0x04, 0xe3, 0x20);
> +       if (err)
> +               goto error;
> +
> +       /* [7] RCO SS enable */
> +       err = ps8622_set(cl, 0x04, 0xe2, 0x80);
> +       if (err)
> +               goto error;
> +
> +       /* RPHY Setting
> +        * [3:2] CDR tune wait cycle before measure for fine tune
> +        * b00: 1us b01: 0.5us b10:2us, b11: 4us
> +        */
> +       err = ps8622_set(cl, 0x04, 0x8a, 0x0c);
> +       if (err)
> +               goto error;
> +
> +       /* [3] RFD always on */
> +       err = ps8622_set(cl, 0x04, 0x89, 0x08);
> +       if (err)
> +               goto error;
> +
> +       /* CTN lock in/out: 20000ppm/80000ppm. Lock out 2 times. */
> +       err = ps8622_set(cl, 0x04, 0x71, 0x2d);
> +       if (err)
> +               goto error;
> +
> +       /* 2.7G CDR settings: NOF=40LSB for HBR CDR  setting */
> +       err = ps8622_set(cl, 0x04, 0x7d, 0x07);
> +       if (err)
> +               goto error;
> +
> +       /* [1:0] Fmin=+4bands */
> +       err = ps8622_set(cl, 0x04, 0x7b, 0x00);
> +       if (err)
> +               goto error;
> +
> +       /* [7:5] DCO_FTRNG=+-40% */
> +       err = ps8622_set(cl, 0x04, 0x7a, 0xfd);
> +       if (err)
> +               goto error;
> +
> +       /* 1.62G CDR settings: [5:2]NOF=64LSB [1:0]DCO scale is 2/5 */
> +       err = ps8622_set(cl, 0x04, 0xc0, 0x12);
> +       if (err)
> +               goto error;
> +
> +       /* Gitune=-37% */
> +       err = ps8622_set(cl, 0x04, 0xc1, 0x92);
> +       if (err)
> +               goto error;
> +
> +       /* Fbstep=100% */
> +       err = ps8622_set(cl, 0x04, 0xc2, 0x1c);
> +       if (err)
> +               goto error;
> +
> +       /* [7] LOS signal disable */
> +       err = ps8622_set(cl, 0x04, 0x32, 0x80);
> +       if (err)
> +               goto error;
> +
> +       /* RPIO Setting: [7:4] LVDS driver bias current : 75% (250mV swing) */
> +       err = ps8622_set(cl, 0x04, 0x00, 0xb0);
> +       if (err)
> +               goto error;
> +
> +       /* [7:6] Right-bar GPIO output strength is 8mA */
> +       err = ps8622_set(cl, 0x04, 0x15, 0x40);
> +       if (err)
> +               goto error;
> +
> +       /* EQ Training State Machine Setting, RCO calibration start */
> +       err = ps8622_set(cl, 0x04, 0x54, 0x10);
> +       if (err)
> +               goto error;
> +
> +       /* Logic, needs more than 10 I2C command */
> +       /* [4:0] MAX_LANE_COUNT set to max supported lanes */
> +       err = ps8622_set(cl, 0x01, 0x02, 0x80 | ps8622->max_lane_count);
> +       if (err)
> +               goto error;
> +
> +       /* [4:0] LANE_COUNT_SET set to chosen lane count */
> +       err = ps8622_set(cl, 0x01, 0x21, 0x80 | ps8622->lane_count);
> +       if (err)
> +               goto error;
> +
> +       err = ps8622_set(cl, 0x00, 0x52, 0x20);
> +       if (err)
> +               goto error;
> +
> +       /* HPD CP toggle enable */
> +       err = ps8622_set(cl, 0x00, 0xf1, 0x03);
> +       if (err)
> +               goto error;
> +
> +       err = ps8622_set(cl, 0x00, 0x62, 0x41);
> +       if (err)
> +               goto error;
> +
> +       /* Counter number, add 1ms counter delay */
> +       err = ps8622_set(cl, 0x00, 0xf6, 0x01);
> +       if (err)
> +               goto error;
> +
> +       /* [6]PWM function control by DPCD0040f[7], default is PWM block */
> +       err = ps8622_set(cl, 0x00, 0x77, 0x06);
> +       if (err)
> +               goto error;
> +
> +       /* 04h Adjust VTotal toleranceto fix the 30Hz no display issue */
> +       err = ps8622_set(cl, 0x00, 0x4c, 0x04);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD00400='h00, Parade OUI ='h001cf8 */
> +       err = ps8622_set(cl, 0x01, 0xc0, 0x00);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD00401='h1c */
> +       err = ps8622_set(cl, 0x01, 0xc1, 0x1c);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD00402='hf8 */
> +       err = ps8622_set(cl, 0x01, 0xc2, 0xf8);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD403~408 = ASCII code, D2SLV5='h4432534c5635 */
> +       err = ps8622_set(cl, 0x01, 0xc3, 0x44);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD404 */
> +       err = ps8622_set(cl, 0x01, 0xc4, 0x32);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD405 */
> +       err = ps8622_set(cl, 0x01, 0xc5, 0x53);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD406 */
> +       err = ps8622_set(cl, 0x01, 0xc6, 0x4c);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD407 */
> +       err = ps8622_set(cl, 0x01, 0xc7, 0x56);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD408 */
> +       err = ps8622_set(cl, 0x01, 0xc8, 0x35);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD40A, Initial Code major revision '01' */
> +       err = ps8622_set(cl, 0x01, 0xca, 0x01);
> +       if (err)
> +               goto error;
> +
> +       /* DPCD40B, Initial Code minor revision '05' */
> +       err = ps8622_set(cl, 0x01, 0xcb, 0x05);
> +       if (err)
> +               goto error;
> +
> +
> +       if (ps8622->bl) {
> +               /* DPCD720, internal PWM */
> +               err = ps8622_set(cl, 0x01, 0xa5, 0xa0);
> +               if (err)
> +                       goto error;
> +
> +               /* FFh for 100% brightness, 0h for 0% brightness */
> +               err = ps8622_set(cl, 0x01, 0xa7,
> +                               ps8622->bl->props.brightness);
> +               if (err)
> +                       goto error;
> +       } else {
> +               /* DPCD720, external PWM */
> +               err = ps8622_set(cl, 0x01, 0xa5, 0x80);
> +               if (err)
> +                       goto error;
> +       }
> +
> +       /* Set LVDS output as 6bit-VESA mapping, single LVDS channel */
> +       err = ps8622_set(cl, 0x01, 0xcc, 0x13);
> +       if (err)
> +               goto error;
> +
> +       /* Enable SSC set by register */
> +       err = ps8622_set(cl, 0x02, 0xb1, 0x20);
> +       if (err)
> +               goto error;
> +
> +       /* Set SSC enabled and +/-1% central spreading */
> +       err = ps8622_set(cl, 0x04, 0x10, 0x16);
> +       if (err)
> +               goto error;
> +
> +       /* Logic end */
> +       /* MPU Clock source: LC => RCO */
> +       err = ps8622_set(cl, 0x04, 0x59, 0x60);
> +       if (err)
> +               goto error;
> +
> +       /* LC -> RCO */
> +       err = ps8622_set(cl, 0x04, 0x54, 0x14);
> +       if (err)
> +               goto error;
> +
> +       /* HPD high */
> +       err = ps8622_set(cl, 0x02, 0xa1, 0x91);
> +
> +error:
> +       return err ? -EIO : 0;
> +}
> +
> +static int ps8622_backlight_update(struct backlight_device *bl)
> +{
> +       struct ps8622_bridge *ps8622 = dev_get_drvdata(&bl->dev);
> +       int ret, brightness = bl->props.brightness;
> +
> +       if (bl->props.power != FB_BLANK_UNBLANK ||
> +           bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
> +               brightness = 0;
> +
> +       if (!ps8622->enabled)
> +               return -EINVAL;
> +
> +       ret = ps8622_set(ps8622->client, 0x01, 0xa7, brightness);
> +
> +       return ret;
> +}
> +
> +static const struct backlight_ops ps8622_backlight_ops = {
> +       .update_status  = ps8622_backlight_update,
> +};
> +
> +static void ps8622_pre_enable(struct drm_bridge *bridge)
> +{
> +       struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
> +       int ret;
> +
> +       if (ps8622->enabled)
> +               return;
> +
> +       gpiod_set_value(ps8622->gpio_rst, 0);
> +
> +       if (ps8622->v12) {
> +               ret = regulator_enable(ps8622->v12);
> +               if (ret)
> +                       DRM_ERROR("fails to enable ps8622->v12");
> +       }
> +
> +       if (drm_panel_prepare(ps8622->panel)) {
> +               DRM_ERROR("failed to prepare panel\n");
> +               return;
> +       }
> +
> +       gpiod_set_value(ps8622->gpio_slp, 1);
> +
> +       /*
> +        * T1 is the range of time that it takes for the power to rise after we
> +        * enable the lcd/ps8622 fet. T2 is the range of time in which the
> +        * data sheet specifies we should deassert the reset pin.
> +        *
> +        * If it takes T1.max for the power to rise, we need to wait atleast
> +        * T2.min before deasserting the reset pin. If it takes T1.min for the
> +        * power to rise, we need to wait at most T2.max before deasserting the
> +        * reset pin.
> +        */
> +       usleep_range(PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US,
> +                    PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US);
> +
> +       gpiod_set_value(ps8622->gpio_rst, 1);
> +
> +       /* wait 20ms after RST high */
> +       usleep_range(20000, 30000);
> +
> +       ret = ps8622_send_config(ps8622);
> +       if (ret) {
> +               DRM_ERROR("Failed to send config to bridge (%d)\n", ret);
> +               return;
> +       }
> +
> +       ps8622->enabled = true;
> +}
> +
> +static void ps8622_enable(struct drm_bridge *bridge)
> +{
> +       struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
> +
> +       if (drm_panel_enable(ps8622->panel)) {
> +               DRM_ERROR("failed to enable panel\n");
> +               return;
> +       }
> +}
> +
> +static void ps8622_disable(struct drm_bridge *bridge)
> +{
> +       struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
> +
> +       if (drm_panel_disable(ps8622->panel)) {
> +               DRM_ERROR("failed to disable panel\n");
> +               return;
> +       }
> +       msleep(PS8622_PWMO_END_T12_MS);
> +}
> +
> +static void ps8622_post_disable(struct drm_bridge *bridge)
> +{
> +       struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
> +
> +       if (!ps8622->enabled)
> +               return;
> +
> +       ps8622->enabled = false;
> +
> +       /*
> +        * This doesn't matter if the regulators are turned off, but something
> +        * else might keep them on. In that case, we want to assert the slp gpio
> +        * to lower power.
> +        */
> +       gpiod_set_value(ps8622->gpio_slp, 0);
> +
> +       if (drm_panel_unprepare(ps8622->panel)) {
> +               DRM_ERROR("failed to unprepare panel\n");
> +               return;
> +       }
> +
> +       if (ps8622->v12)
> +               regulator_disable(ps8622->v12);
> +
> +       /*
> +        * Sleep for at least the amount of time that it takes the power rail to
> +        * fall to prevent asserting the rst gpio from doing anything.
> +        */
> +       usleep_range(PS8622_POWER_FALL_T16_MAX_US,
> +                    2 * PS8622_POWER_FALL_T16_MAX_US);
> +       gpiod_set_value(ps8622->gpio_rst, 0);
> +
> +       msleep(PS8622_POWER_OFF_T17_MS);
> +}
> +
> +static int ps8622_get_modes(struct drm_connector *connector)
> +{
> +       struct ps8622_bridge *ps8622;
> +
> +       ps8622 = connector_to_ps8622(connector);
> +
> +       return drm_panel_get_modes(ps8622->panel);
> +}
> +
> +static struct drm_encoder *ps8622_best_encoder(struct drm_connector *connector)
> +{
> +       struct ps8622_bridge *ps8622;
> +
> +       ps8622 = connector_to_ps8622(connector);
> +
> +       return ps8622->bridge.encoder;
> +}
> +
> +static const struct drm_connector_helper_funcs ps8622_connector_helper_funcs = {
> +       .get_modes = ps8622_get_modes,
> +       .best_encoder = ps8622_best_encoder,
> +};
> +
> +static enum drm_connector_status ps8622_detect(struct drm_connector *connector,
> +                                                               bool force)
> +{
> +       return connector_status_connected;
> +}
> +
> +static void ps8622_connector_destroy(struct drm_connector *connector)
> +{
> +       drm_connector_cleanup(connector);
> +}
> +
> +static const struct drm_connector_funcs ps8622_connector_funcs = {
> +       .dpms = drm_helper_connector_dpms,
> +       .fill_modes = drm_helper_probe_single_connector_modes,
> +       .detect = ps8622_detect,
> +       .destroy = ps8622_connector_destroy,
> +};
> +
> +int ps8622_attach(struct drm_bridge *bridge)
> +{
> +       struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
> +       int ret;
> +
> +       if (!bridge->encoder) {
> +               DRM_ERROR("Parent encoder object not found");
> +               return -ENODEV;
> +       }
> +
> +       ps8622->connector.polled = DRM_CONNECTOR_POLL_HPD;
> +       ret = drm_connector_init(bridge->dev, &ps8622->connector,
> +                       &ps8622_connector_funcs, DRM_MODE_CONNECTOR_LVDS);
> +       if (ret) {
> +               DRM_ERROR("Failed to initialize connector with drm\n");
> +               return ret;
> +       }
> +       drm_connector_helper_add(&ps8622->connector,
> +                                       &ps8622_connector_helper_funcs);
> +       drm_connector_register(&ps8622->connector);
> +       drm_mode_connector_attach_encoder(&ps8622->connector,
> +                                                       bridge->encoder);
> +
> +       if (ps8622->panel)
> +               drm_panel_attach(ps8622->panel, &ps8622->connector);
> +
> +       drm_helper_hpd_irq_event(ps8622->connector.dev);
> +
> +       return ret;
> +}
> +
> +static const struct drm_bridge_funcs ps8622_bridge_funcs = {
> +       .pre_enable = ps8622_pre_enable,
> +       .enable = ps8622_enable,
> +       .disable = ps8622_disable,
> +       .post_disable = ps8622_post_disable,
> +       .attach = ps8622_attach,
> +};
> +
> +static const struct of_device_id ps8622_devices[] = {
> +       {.compatible = "parade,ps8622",},
> +       {.compatible = "parade,ps8625",},
> +       {}
> +};
> +MODULE_DEVICE_TABLE(of, ps8622_devices);
> +
> +static int ps8622_probe(struct i2c_client *client,
> +                                       const struct i2c_device_id *id)
> +{
> +       struct device *dev = &client->dev;
> +       struct device_node *endpoint, *panel_node;
> +       struct ps8622_bridge *ps8622;
> +       int ret;
> +
> +       ps8622 = devm_kzalloc(dev, sizeof(*ps8622), GFP_KERNEL);
> +       if (!ps8622)
> +               return -ENOMEM;
> +
> +       endpoint = of_graph_get_next_endpoint(dev->of_node, NULL);
> +       if (endpoint) {
> +               panel_node = of_graph_get_remote_port_parent(endpoint);
> +               if (panel_node) {
> +                       ps8622->panel = of_drm_find_panel(panel_node);
> +                       of_node_put(panel_node);
> +                       if (!ps8622->panel)
> +                               return -EPROBE_DEFER;
> +               }
> +       }
> +
> +       ps8622->client = client;
> +
> +       ps8622->v12 = devm_regulator_get(dev, "vdd12");
> +       if (IS_ERR(ps8622->v12)) {
> +               dev_info(dev, "no 1.2v regulator found for PS8622\n");
> +               ps8622->v12 = NULL;
> +       }
> +
> +       ps8622->gpio_slp = devm_gpiod_get(dev, "sleep");
> +       if (IS_ERR(ps8622->gpio_slp)) {
> +               ret = PTR_ERR(ps8622->gpio_slp);
> +               dev_err(dev, "cannot get gpio_slp %d\n", ret);
> +               return ret;
> +       }
> +       ret = gpiod_direction_output(ps8622->gpio_slp, 1);
> +       if (ret) {
> +               dev_err(dev, "cannot configure gpio_slp\n");
> +               return ret;
> +       }
> +
> +       ps8622->gpio_rst = devm_gpiod_get(dev, "reset");
> +       if (IS_ERR(ps8622->gpio_rst)) {
> +               ret = PTR_ERR(ps8622->gpio_rst);
> +               dev_err(dev, "cannot get gpio_rst %d\n", ret);
> +               return ret;
> +       }
> +       /*
> +        * Assert the reset pin high to avoid the bridge being
> +        * initialized prematurely
> +        */
> +       ret = gpiod_direction_output(ps8622->gpio_rst, 1);
> +       if (ret) {
> +               dev_err(dev, "cannot configure gpio_rst\n");
> +               return ret;
> +       }
> +
> +       ps8622->max_lane_count = id->driver_data;
> +
> +       if (of_property_read_u32(dev->of_node, "lane-count",
> +                                               &ps8622->lane_count)) {
> +               ps8622->lane_count = ps8622->max_lane_count;
> +       } else if (ps8622->lane_count > ps8622->max_lane_count) {
> +               dev_info(dev, "lane-count property is too high,"
> +                                               "using max_lane_count\n");
> +               ps8622->lane_count = ps8622->max_lane_count;
> +       }
> +
> +       if (!of_find_property(dev->of_node, "use-external-pwm", NULL)) {
> +               ps8622->bl = backlight_device_register("ps8622-backlight",
> +                               dev, ps8622, &ps8622_backlight_ops,
> +                               NULL);
> +               if (IS_ERR(ps8622->bl)) {
> +                       DRM_ERROR("failed to register backlight\n");
> +                       ret = PTR_ERR(ps8622->bl);
> +                       ps8622->bl = NULL;
> +                       return ret;
> +               }
> +               ps8622->bl->props.max_brightness = PS8622_MAX_BRIGHTNESS;
> +               ps8622->bl->props.brightness = PS8622_MAX_BRIGHTNESS;
> +       }
> +
> +       ps8622->bridge.funcs = &ps8622_bridge_funcs;
> +       ps8622->bridge.of_node = dev->of_node;
> +       ret = drm_bridge_add(&ps8622->bridge);
> +       if (ret) {
> +               DRM_ERROR("Failed to add bridge\n");
> +               return ret;
> +       }
> +
> +       i2c_set_clientdata(client, ps8622);
> +
> +       return 0;
> +}
> +
> +static int ps8622_remove(struct i2c_client *client)
> +{
> +       struct ps8622_bridge *ps8622 = i2c_get_clientdata(client);
> +
> +       if (ps8622->bl)
> +               backlight_device_unregister(ps8622->bl);
> +
> +       drm_bridge_remove(&ps8622->bridge);
> +
> +       return 0;
> +}
> +
> +static const struct i2c_device_id ps8622_i2c_table[] = {
> +       /* Device type, max_lane_count */
> +       {"ps8622", 1},
> +       {"ps8625", 2},
> +       {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ps8622_i2c_table);
> +
> +struct i2c_driver ps8622_driver = {
> +       .id_table       = ps8622_i2c_table,
> +       .probe          = ps8622_probe,
> +       .remove         = ps8622_remove,
> +       .driver         = {
> +               .name   = "ps8622",
> +               .owner  = THIS_MODULE,
> +               .of_match_table = ps8622_devices,
> +       },
> +};
> +module_i2c_driver(ps8622_driver);
> +
> +MODULE_AUTHOR("Vincent Palatin <vpalatin at chromium.org>");
> +MODULE_DESCRIPTION("Parade ps8622/ps8625 eDP-LVDS converter driver");
> +MODULE_LICENSE("GPL v2");
> --
> 1.7.9.5
>



More information about the linux-arm-kernel mailing list