[PATCH v3 02/10] ARM: tegra: Move out nyan-generic parts out from the nyan-big DT

Tomeu Vizoso tomeu.vizoso at collabora.com
Wed Jan 28 02:51:00 PST 2015


In preparation for adding the DT for the nyan-blaze board.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso at collabora.com>
---
 arch/arm/boot/dts/tegra124-nyan-big.dts | 684 +-------------------------------
 arch/arm/boot/dts/tegra124-nyan.dtsi    | 676 +++++++++++++++++++++++++++++++
 2 files changed, 683 insertions(+), 677 deletions(-)
 create mode 100644 arch/arm/boot/dts/tegra124-nyan.dtsi

diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
index eda6ae7..fa222c6 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-big.dts
@@ -1,46 +1,20 @@
 /dts-v1/;
 
-#include <dt-bindings/input/input.h>
-#include "tegra124.dtsi"
+#include "tegra124-nyan.dtsi"
 
 / {
 	model = "Acer Chromebook 13 CB5-311";
 	compatible = "google,nyan-big", "nvidia,tegra124";
 
-	aliases {
-		rtc0 = "/i2c at 0,7000d000/pmic at 40";
-		rtc1 = "/rtc at 0,7000e000";
-		serial0 = &uarta;
-	};
+	panel: panel {
+		compatible = "auo,b133xtn01";
 
-	memory {
-		reg = <0x0 0x80000000 0x0 0x80000000>;
+		backlight = <&backlight>;
+		ddc-i2c-bus = <&dpaux>;
 	};
 
-	host1x at 0,50000000 {
-		hdmi at 0,54280000 {
-			status = "okay";
-
-			vdd-supply = <&vdd_3v3_hdmi>;
-			pll-supply = <&vdd_hdmi_pll>;
-			hdmi-supply = <&vdd_5v0_hdmi>;
-
-			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
-			nvidia,hpd-gpio =
-				<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
-		};
-
-		sor at 0,54540000 {
-			status = "okay";
-
-			nvidia,dpaux = <&dpaux>;
-			nvidia,panel = <&panel>;
-		};
-
-		dpaux at 0,545c0000 {
-			vdd-supply = <&vdd_3v3_panel>;
-			status = "okay";
-		};
+	sdhci at 0,700b0400 { /* SD Card on this bus */
+		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
 	};
 
 	pinmux at 0,70000868 {
@@ -492,648 +466,4 @@
 			};
 		};
 	};
-
-	serial at 0,70006000 {
-		/* Debug connector on the bottom of the board near SD card. */
-		status = "okay";
-	};
-
-	pwm at 0,7000a000 {
-		status = "okay";
-	};
-
-	i2c at 0,7000c000 {
-		status = "okay";
-		clock-frequency = <100000>;
-
-		acodec: audio-codec at 10 {
-			compatible = "maxim,max98090";
-			reg = <0x10>;
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
-		};
-
-		temperature-sensor at 4c {
-			compatible = "ti,tmp451";
-			reg = <0x4c>;
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
-
-			#thermal-sensor-cells = <1>;
-		};
-	};
-
-	i2c at 0,7000c400 {
-		status = "okay";
-		clock-frequency = <100000>;
-	};
-
-	i2c at 0,7000c500 {
-		status = "okay";
-		clock-frequency = <400000>;
-
-		tpm at 20 {
-			compatible = "infineon,slb9645tt";
-			reg = <0x20>;
-		};
-	};
-
-	hdmi_ddc: i2c at 0,7000c700 {
-		status = "okay";
-		clock-frequency = <100000>;
-	};
-
-	i2c at 0,7000d000 {
-		status = "okay";
-		clock-frequency = <400000>;
-
-		pmic: pmic at 40 {
-			compatible = "ams,as3722";
-			reg = <0x40>;
-			interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
-
-			ams,system-power-controller;
-
-			#interrupt-cells = <2>;
-			interrupt-controller;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&as3722_default>;
-
-			as3722_default: pinmux {
-				gpio0 {
-					pins = "gpio0";
-					function = "gpio";
-					bias-pull-down;
-				};
-
-				gpio1 {
-					pins = "gpio1";
-					function = "gpio";
-					bias-pull-up;
-				};
-
-				gpio2_4_7 {
-					pins = "gpio2", "gpio4", "gpio7";
-					function = "gpio";
-					bias-pull-up;
-				};
-
-				gpio3_6 {
-					pins = "gpio3", "gpio6";
-					bias-high-impedance;
-				};
-
-				gpio5 {
-					pins = "gpio5";
-					function = "clk32k-out";
-					bias-pull-down;
-				};
-			};
-
-			regulators {
-				vsup-sd2-supply = <&vdd_5v0_sys>;
-				vsup-sd3-supply = <&vdd_5v0_sys>;
-				vsup-sd4-supply = <&vdd_5v0_sys>;
-				vsup-sd5-supply = <&vdd_5v0_sys>;
-				vin-ldo0-supply = <&vdd_1v35_lp0>;
-				vin-ldo1-6-supply = <&vdd_3v3_run>;
-				vin-ldo2-5-7-supply = <&vddio_1v8>;
-				vin-ldo3-4-supply = <&vdd_3v3_sys>;
-				vin-ldo9-10-supply = <&vdd_5v0_sys>;
-				vin-ldo11-supply = <&vdd_3v3_run>;
-
-				sd0 {
-					regulator-name = "+VDD_CPU_AP";
-					regulator-min-microvolt = <700000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-min-microamp = <3500000>;
-					regulator-max-microamp = <3500000>;
-					regulator-always-on;
-					regulator-boot-on;
-					ams,ext-control = <2>;
-				};
-
-				sd1 {
-					regulator-name = "+VDD_CORE";
-					regulator-min-microvolt = <700000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-min-microamp = <2500000>;
-					regulator-max-microamp = <4000000>;
-					regulator-always-on;
-					regulator-boot-on;
-					ams,ext-control = <1>;
-				};
-
-				vdd_1v35_lp0: sd2 {
-					regulator-name = "+1.35V_LP0(sd2)";
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				sd3 {
-					regulator-name = "+1.35V_LP0(sd3)";
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				vdd_1v05_run: sd4 {
-					regulator-name = "+1.05V_RUN";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-				};
-
-				vddio_1v8: sd5 {
-					regulator-name = "+1.8V_VDDIO";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				sd6 {
-					regulator-name = "+VDD_GPU_AP";
-					regulator-min-microvolt = <650000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-min-microamp = <3500000>;
-					regulator-max-microamp = <3500000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo0 {
-					regulator-name = "+1.05V_RUN_AVDD";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					regulator-boot-on;
-					regulator-always-on;
-					ams,ext-control = <1>;
-				};
-
-				ldo1 {
-					regulator-name = "+1.8V_RUN_CAM";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				ldo2 {
-					regulator-name = "+1.2V_GEN_AVDD";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo3 {
-					regulator-name = "+1.00V_LP0_VDD_RTC";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-					regulator-boot-on;
-					regulator-always-on;
-					ams,enable-tracking;
-				};
-
-				vdd_run_cam: ldo4 {
-					regulator-name = "+3.3V_RUN_CAM";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo5 {
-					regulator-name = "+1.2V_RUN_CAM_FRONT";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				vddio_sdmmc3: ldo6 {
-					regulator-name = "+VDDIO_SDMMC3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				ldo7 {
-					regulator-name = "+1.05V_RUN_CAM_REAR";
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-				};
-
-				ldo9 {
-					regulator-name = "+2.8V_RUN_TOUCH";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo10 {
-					regulator-name = "+2.8V_RUN_CAM_AF";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-				};
-
-				ldo11 {
-					regulator-name = "+1.8V_RUN_VPP_FUSE";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-			};
-		};
-	};
-
-	spi at 0,7000d400 {
-		status = "okay";
-
-		cros_ec: cros-ec at 0 {
-			compatible = "google,cros-ec-spi";
-			spi-max-frequency = <3000000>;
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
-			reg = <0>;
-
-			google,cros-ec-spi-msg-delay = <2000>;
-
-			i2c-tunnel {
-				compatible = "google,cros-ec-i2c-tunnel";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				google,remote-bus = <0>;
-
-				charger: bq24735 at 9 {
-					compatible = "ti,bq24735";
-					reg = <0x9>;
-					interrupt-parent = <&gpio>;
-					interrupts = <TEGRA_GPIO(J, 0)
-							GPIO_ACTIVE_HIGH>;
-					ti,ac-detect-gpios = <&gpio
-							TEGRA_GPIO(J, 0)
-							GPIO_ACTIVE_HIGH>;
-				};
-
-				battery: sbs-battery at b {
-					compatible = "sbs,sbs-battery";
-					reg = <0xb>;
-					sbs,i2c-retry-count = <2>;
-					sbs,poll-retry-count = <10>;
-					power-supplies = <&charger>;
-				};
-			};
-		};
-	};
-
-	spi at 0,7000da00 {
-		status = "okay";
-		spi-max-frequency = <25000000>;
-
-		flash at 0 {
-			compatible = "winbond,w25q32dw";
-			reg = <0>;
-		};
-	};
-
-	pmc at 0,7000e400 {
-		nvidia,invert-interrupt;
-		nvidia,suspend-mode = <0>;
-		nvidia,cpu-pwr-good-time = <500>;
-		nvidia,cpu-pwr-off-time = <300>;
-		nvidia,core-pwr-good-time = <641 3845>;
-		nvidia,core-pwr-off-time = <61036>;
-		nvidia,core-power-req-active-high;
-		nvidia,sys-clock-req-active-high;
-	};
-
-	hda at 0,70030000 {
-		status = "okay";
-	};
-
-	sdhci at 0,700b0000 { /* WiFi/BT on this bus */
-		status = "okay";
-		power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
-		bus-width = <4>;
-		no-1-8-v;
-		non-removable;
-	};
-
-	sdhci at 0,700b0400 { /* SD Card on this bus */
-		status = "okay";
-		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
-		power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
-		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
-		bus-width = <4>;
-		no-1-8-v;
-		vqmmc-supply = <&vddio_sdmmc3>;
-	};
-
-	sdhci at 0,700b0600 { /* eMMC on this bus */
-		status = "okay";
-		bus-width = <8>;
-		no-1-8-v;
-		non-removable;
-	};
-
-	ahub at 0,70300000 {
-		i2s at 0,70301100 {
-			status = "okay";
-		};
-	};
-
-	usb at 0,7d000000 { /* Rear external USB port. */
-		status = "okay";
-	};
-
-	usb-phy at 0,7d000000 {
-		status = "okay";
-		vbus-supply = <&vdd_usb1_vbus>;
-	};
-
-	usb at 0,7d004000 { /* Internal webcam. */
-		status = "okay";
-	};
-
-	usb-phy at 0,7d004000 {
-		status = "okay";
-		vbus-supply = <&vdd_run_cam>;
-	};
-
-	usb at 0,7d008000 { /* Left external USB port. */
-		status = "okay";
-	};
-
-	usb-phy at 0,7d008000 {
-		status = "okay";
-		vbus-supply = <&vdd_usb3_vbus>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-
-		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
-		power-supply = <&vdd_led>;
-		pwms = <&pwm 1 1000000>;
-
-		default-brightness-level = <224>;
-		brightness-levels =
-			<  0   1   2   3   4   5   6   7
-			   8   9  10  11  12  13  14  15
-			  16  17  18  19  20  21  22  23
-			  24  25  26  27  28  29  30  31
-			  32  33  34  35  36  37  38  39
-			  40  41  42  43  44  45  46  47
-			  48  49  50  51  52  53  54  55
-			  56  57  58  59  60  61  62  63
-			  64  65  66  67  68  69  70  71
-			  72  73  74  75  76  77  78  79
-			  80  81  82  83  84  85  86  87
-			  88  89  90  91  92  93  94  95
-			  96  97  98  99 100 101 102 103
-			 104 105 106 107 108 109 110 111
-			 112 113 114 115 116 117 118 119
-			 120 121 122 123 124 125 126 127
-			 128 129 130 131 132 133 134 135
-			 136 137 138 139 140 141 142 143
-			 144 145 146 147 148 149 150 151
-			 152 153 154 155 156 157 158 159
-			 160 161 162 163 164 165 166 167
-			 168 169 170 171 172 173 174 175
-			 176 177 178 179 180 181 182 183
-			 184 185 186 187 188 189 190 191
-			 192 193 194 195 196 197 198 199
-			 200 201 202 203 204 205 206 207
-			 208 209 210 211 212 213 214 215
-			 216 217 218 219 220 221 222 223
-			 224 225 226 227 228 229 230 231
-			 232 233 234 235 236 237 238 239
-			 240 241 242 243 244 245 246 247
-			 248 249 250 251 252 253 254 255
-			 256>;
-	};
-
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock at 0 {
-			compatible = "fixed-clock";
-			reg = <0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		lid {
-			label = "Lid";
-			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
-			linux,input-type = <5>;
-			linux,code = <KEY_RESERVED>;
-			debounce-interval = <1>;
-			gpio-key,wakeup;
-		};
-
-		power {
-			label = "Power";
-			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <30>;
-			gpio-key,wakeup;
-		};
-	};
-
-	panel: panel {
-		compatible = "auo,b133xtn01";
-
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_mux: regulator at 0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "+VDD_MUX";
-			regulator-min-microvolt = <12000000>;
-			regulator-max-microvolt = <12000000>;
-			regulator-always-on;
-			regulator-boot-on;
-		};
-
-		vdd_5v0_sys: regulator at 1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "+5V_SYS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
-
-		vdd_3v3_sys: regulator at 2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "+3.3V_SYS";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			vin-supply = <&vdd_mux>;
-		};
-
-		vdd_3v3_run: regulator at 3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "+3.3V_RUN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
-
-		vdd_3v3_hdmi: regulator at 4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vdd_3v3_run>;
-		};
-
-		vdd_led: regulator at 5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "+VDD_LED";
-			gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_mux>;
-		};
-
-		vdd_5v0_ts: regulator at 6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "+5V_VDD_TS_SW";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-boot-on;
-			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
-
-		vdd_usb1_vbus: regulator at 7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			regulator-name = "+5V_USB_HS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
-
-		vdd_usb3_vbus: regulator at 8 {
-			compatible = "regulator-fixed";
-			reg = <8>;
-			regulator-name = "+5V_USB_SS";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			gpio-open-drain;
-			vin-supply = <&vdd_5v0_sys>;
-		};
-
-		vdd_3v3_panel: regulator at 9 {
-			compatible = "regulator-fixed";
-			reg = <9>;
-			regulator-name = "+3.3V_PANEL";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_run>;
-		};
-
-		vdd_3v3_lp0: regulator at 10 {
-			compatible = "regulator-fixed";
-			reg = <10>;
-			regulator-name = "+3.3V_LP0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			/*
-			 * TODO: find a way to wire this up with the USB EHCI
-			 * controllers so that it can be enabled on demand.
-			 */
-			regulator-always-on;
-			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_3v3_sys>;
-		};
-
-		vdd_hdmi_pll: regulator at 11 {
-			compatible = "regulator-fixed";
-			reg = <11>;
-			regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
-			vin-supply = <&vdd_1v05_run>;
-		};
-
-		vdd_5v0_hdmi: regulator at 12 {
-			compatible = "regulator-fixed";
-			reg = <12>;
-			regulator-name = "+5V_HDMI_CON";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			vin-supply = <&vdd_5v0_sys>;
-		};
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-max98090-nyan",
-			     "nvidia,tegra-audio-max98090";
-		nvidia,model = "GoogleNyan";
-
-		nvidia,audio-routing =
-			"Headphones", "HPR",
-			"Headphones", "HPL",
-			"Speakers", "SPKR",
-			"Speakers", "SPKL",
-			"Mic Jack", "MICBIAS",
-			"DMICL", "Int Mic",
-			"DMICR", "Int Mic",
-			"IN34", "Mic Jack";
-
-		nvidia,i2s-controller = <&tegra_i2s1>;
-		nvidia,audio-codec = <&acodec>;
-
-		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
-			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA124_CLK_EXTERN1>;
-		clock-names = "pll_a", "pll_a_out0", "mclk";
-
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
-		nvidia,mic-det-gpios =
-				<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
-	};
 };
-
-#include "cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/tegra124-nyan.dtsi
new file mode 100644
index 0000000..9f25ff1
--- /dev/null
+++ b/arch/arm/boot/dts/tegra124-nyan.dtsi
@@ -0,0 +1,676 @@
+#include <dt-bindings/input/input.h>
+#include "tegra124.dtsi"
+
+/ {
+	aliases {
+		rtc0 = "/i2c at 0,7000d000/pmic at 40";
+		rtc1 = "/rtc at 0,7000e000";
+		serial0 = &uarta;
+	};
+
+	memory {
+		reg = <0x0 0x80000000 0x0 0x80000000>;
+	};
+
+	host1x at 0,50000000 {
+		hdmi at 0,54280000 {
+			status = "okay";
+
+			vdd-supply = <&vdd_3v3_hdmi>;
+			pll-supply = <&vdd_hdmi_pll>;
+			hdmi-supply = <&vdd_5v0_hdmi>;
+
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+			nvidia,hpd-gpio =
+				<&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		sor at 0,54540000 {
+			status = "okay";
+
+			nvidia,dpaux = <&dpaux>;
+			nvidia,panel = <&panel>;
+		};
+
+		dpaux at 0,545c0000 {
+			vdd-supply = <&vdd_3v3_panel>;
+			status = "okay";
+		};
+	};
+
+	serial at 0,70006000 {
+		/* Debug connector on the bottom of the board near SD card. */
+		status = "okay";
+	};
+
+	pwm at 0,7000a000 {
+		status = "okay";
+	};
+
+	i2c at 0,7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		acodec: audio-codec at 10 {
+			compatible = "maxim,max98090";
+			reg = <0x10>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
+		};
+
+		temperature-sensor at 4c {
+			compatible = "ti,tmp451";
+			reg = <0x4c>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	i2c at 0,7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c at 0,7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		tpm at 20 {
+			compatible = "infineon,slb9645tt";
+			reg = <0x20>;
+		};
+	};
+
+	hdmi_ddc: i2c at 0,7000c700 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c at 0,7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		pmic: pmic at 40 {
+			compatible = "ams,as3722";
+			reg = <0x40>;
+			interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			ams,system-power-controller;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&as3722_default>;
+
+			as3722_default: pinmux {
+				gpio0 {
+					pins = "gpio0";
+					function = "gpio";
+					bias-pull-down;
+				};
+
+				gpio1 {
+					pins = "gpio1";
+					function = "gpio";
+					bias-pull-up;
+				};
+
+				gpio2_4_7 {
+					pins = "gpio2", "gpio4", "gpio7";
+					function = "gpio";
+					bias-pull-up;
+				};
+
+				gpio3_6 {
+					pins = "gpio3", "gpio6";
+					bias-high-impedance;
+				};
+
+				gpio5 {
+					pins = "gpio5";
+					function = "clk32k-out";
+					bias-pull-down;
+				};
+			};
+
+			regulators {
+				vsup-sd2-supply = <&vdd_5v0_sys>;
+				vsup-sd3-supply = <&vdd_5v0_sys>;
+				vsup-sd4-supply = <&vdd_5v0_sys>;
+				vsup-sd5-supply = <&vdd_5v0_sys>;
+				vin-ldo0-supply = <&vdd_1v35_lp0>;
+				vin-ldo1-6-supply = <&vdd_3v3_run>;
+				vin-ldo2-5-7-supply = <&vddio_1v8>;
+				vin-ldo3-4-supply = <&vdd_3v3_sys>;
+				vin-ldo9-10-supply = <&vdd_5v0_sys>;
+				vin-ldo11-supply = <&vdd_3v3_run>;
+
+				sd0 {
+					regulator-name = "+VDD_CPU_AP";
+					regulator-min-microvolt = <700000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-min-microamp = <3500000>;
+					regulator-max-microamp = <3500000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ams,ext-control = <2>;
+				};
+
+				sd1 {
+					regulator-name = "+VDD_CORE";
+					regulator-min-microvolt = <700000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-min-microamp = <2500000>;
+					regulator-max-microamp = <4000000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ams,ext-control = <1>;
+				};
+
+				vdd_1v35_lp0: sd2 {
+					regulator-name = "+1.35V_LP0(sd2)";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				sd3 {
+					regulator-name = "+1.35V_LP0(sd3)";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_1v05_run: sd4 {
+					regulator-name = "+1.05V_RUN";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+				};
+
+				vddio_1v8: sd5 {
+					regulator-name = "+1.8V_VDDIO";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				sd6 {
+					regulator-name = "+VDD_GPU_AP";
+					regulator-min-microvolt = <650000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-min-microamp = <3500000>;
+					regulator-max-microamp = <3500000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				ldo0 {
+					regulator-name = "+1.05V_RUN_AVDD";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-boot-on;
+					regulator-always-on;
+					ams,ext-control = <1>;
+				};
+
+				ldo1 {
+					regulator-name = "+1.8V_RUN_CAM";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo2 {
+					regulator-name = "+1.2V_GEN_AVDD";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				ldo3 {
+					regulator-name = "+1.00V_LP0_VDD_RTC";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-boot-on;
+					regulator-always-on;
+					ams,enable-tracking;
+				};
+
+				vdd_run_cam: ldo4 {
+					regulator-name = "+3.3V_RUN_CAM";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo5 {
+					regulator-name = "+1.2V_RUN_CAM_FRONT";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				vddio_sdmmc3: ldo6 {
+					regulator-name = "+VDDIO_SDMMC3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo7 {
+					regulator-name = "+1.05V_RUN_CAM_REAR";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+				};
+
+				ldo9 {
+					regulator-name = "+2.8V_RUN_TOUCH";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo10 {
+					regulator-name = "+2.8V_RUN_CAM_AF";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo11 {
+					regulator-name = "+1.8V_RUN_VPP_FUSE";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+			};
+		};
+	};
+
+	spi at 0,7000d400 {
+		status = "okay";
+
+		cros_ec: cros-ec at 0 {
+			compatible = "google,cros-ec-spi";
+			spi-max-frequency = <3000000>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
+			reg = <0>;
+
+			google,cros-ec-spi-msg-delay = <2000>;
+
+			i2c-tunnel {
+				compatible = "google,cros-ec-i2c-tunnel";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				google,remote-bus = <0>;
+
+				charger: bq24735 at 9 {
+					compatible = "ti,bq24735";
+					reg = <0x9>;
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(J, 0)
+							GPIO_ACTIVE_HIGH>;
+					ti,ac-detect-gpios = <&gpio
+							TEGRA_GPIO(J, 0)
+							GPIO_ACTIVE_HIGH>;
+				};
+
+				battery: sbs-battery at b {
+					compatible = "sbs,sbs-battery";
+					reg = <0xb>;
+					sbs,i2c-retry-count = <2>;
+					sbs,poll-retry-count = <10>;
+					power-supplies = <&charger>;
+				};
+			};
+		};
+	};
+
+	spi at 0,7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+
+		flash at 0 {
+			compatible = "winbond,w25q32dw";
+			reg = <0>;
+		};
+	};
+
+	pmc at 0,7000e400 {
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <0>;
+		nvidia,cpu-pwr-good-time = <500>;
+		nvidia,cpu-pwr-off-time = <300>;
+		nvidia,core-pwr-good-time = <641 3845>;
+		nvidia,core-pwr-off-time = <61036>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+	};
+
+	hda at 0,70030000 {
+		status = "okay";
+	};
+
+	sdhci at 0,700b0000 { /* WiFi/BT on this bus */
+		status = "okay";
+		power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+		no-1-8-v;
+		non-removable;
+	};
+
+	sdhci at 0,700b0400 { /* SD Card on this bus */
+		status = "okay";
+		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+		power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+		no-1-8-v;
+		vqmmc-supply = <&vddio_sdmmc3>;
+	};
+
+	sdhci at 0,700b0600 { /* eMMC on this bus */
+		status = "okay";
+		bus-width = <8>;
+		no-1-8-v;
+		non-removable;
+	};
+
+	ahub at 0,70300000 {
+		i2s at 0,70301100 {
+			status = "okay";
+		};
+	};
+
+	usb at 0,7d000000 { /* Rear external USB port. */
+		status = "okay";
+	};
+
+	usb-phy at 0,7d000000 {
+		status = "okay";
+		vbus-supply = <&vdd_usb1_vbus>;
+	};
+
+	usb at 0,7d004000 { /* Internal webcam. */
+		status = "okay";
+	};
+
+	usb-phy at 0,7d004000 {
+		status = "okay";
+		vbus-supply = <&vdd_run_cam>;
+	};
+
+	usb at 0,7d008000 { /* Left external USB port. */
+		status = "okay";
+	};
+
+	usb-phy at 0,7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_usb3_vbus>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_led>;
+		pwms = <&pwm 1 1000000>;
+
+		default-brightness-level = <224>;
+		brightness-levels =
+			<  0   1   2   3   4   5   6   7
+			   8   9  10  11  12  13  14  15
+			  16  17  18  19  20  21  22  23
+			  24  25  26  27  28  29  30  31
+			  32  33  34  35  36  37  38  39
+			  40  41  42  43  44  45  46  47
+			  48  49  50  51  52  53  54  55
+			  56  57  58  59  60  61  62  63
+			  64  65  66  67  68  69  70  71
+			  72  73  74  75  76  77  78  79
+			  80  81  82  83  84  85  86  87
+			  88  89  90  91  92  93  94  95
+			  96  97  98  99 100 101 102 103
+			 104 105 106 107 108 109 110 111
+			 112 113 114 115 116 117 118 119
+			 120 121 122 123 124 125 126 127
+			 128 129 130 131 132 133 134 135
+			 136 137 138 139 140 141 142 143
+			 144 145 146 147 148 149 150 151
+			 152 153 154 155 156 157 158 159
+			 160 161 162 163 164 165 166 167
+			 168 169 170 171 172 173 174 175
+			 176 177 178 179 180 181 182 183
+			 184 185 186 187 188 189 190 191
+			 192 193 194 195 196 197 198 199
+			 200 201 202 203 204 205 206 207
+			 208 209 210 211 212 213 214 215
+			 216 217 218 219 220 221 222 223
+			 224 225 226 227 228 229 230 231
+			 232 233 234 235 236 237 238 239
+			 240 241 242 243 244 245 246 247
+			 248 249 250 251 252 253 254 255
+			 256>;
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		clk32k_in: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		lid {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>;
+			linux,code = <KEY_RESERVED>;
+			debounce-interval = <1>;
+			gpio-key,wakeup;
+		};
+
+		power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <30>;
+			gpio-key,wakeup;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd_mux: regulator at 0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "+VDD_MUX";
+			regulator-min-microvolt = <12000000>;
+			regulator-max-microvolt = <12000000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vdd_5v0_sys: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "+5V_SYS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+			regulator-boot-on;
+			vin-supply = <&vdd_mux>;
+		};
+
+		vdd_3v3_sys: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "+3.3V_SYS";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+			regulator-boot-on;
+			vin-supply = <&vdd_mux>;
+		};
+
+		vdd_3v3_run: regulator at 3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "+3.3V_RUN";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_3v3_sys>;
+		};
+
+		vdd_3v3_hdmi: regulator at 4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			vin-supply = <&vdd_3v3_run>;
+		};
+
+		vdd_led: regulator at 5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "+VDD_LED";
+			gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_mux>;
+		};
+
+		vdd_5v0_ts: regulator at 6 {
+			compatible = "regulator-fixed";
+			reg = <6>;
+			regulator-name = "+5V_VDD_TS_SW";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-boot-on;
+			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_5v0_sys>;
+		};
+
+		vdd_usb1_vbus: regulator at 7 {
+			compatible = "regulator-fixed";
+			reg = <7>;
+			regulator-name = "+5V_USB_HS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			gpio-open-drain;
+			vin-supply = <&vdd_5v0_sys>;
+		};
+
+		vdd_usb3_vbus: regulator at 8 {
+			compatible = "regulator-fixed";
+			reg = <8>;
+			regulator-name = "+5V_USB_SS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			gpio-open-drain;
+			vin-supply = <&vdd_5v0_sys>;
+		};
+
+		vdd_3v3_panel: regulator at 9 {
+			compatible = "regulator-fixed";
+			reg = <9>;
+			regulator-name = "+3.3V_PANEL";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_3v3_run>;
+		};
+
+		vdd_3v3_lp0: regulator at 10 {
+			compatible = "regulator-fixed";
+			reg = <10>;
+			regulator-name = "+3.3V_LP0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			/*
+			 * TODO: find a way to wire this up with the USB EHCI
+			 * controllers so that it can be enabled on demand.
+			 */
+			regulator-always-on;
+			gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_3v3_sys>;
+		};
+
+		vdd_hdmi_pll: regulator at 11 {
+			compatible = "regulator-fixed";
+			reg = <11>;
+			regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+			vin-supply = <&vdd_1v05_run>;
+		};
+
+		vdd_5v0_hdmi: regulator at 12 {
+			compatible = "regulator-fixed";
+			reg = <12>;
+			regulator-name = "+5V_HDMI_CON";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			vin-supply = <&vdd_5v0_sys>;
+		};
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-max98090-nyan",
+			     "nvidia,tegra-audio-max98090";
+		nvidia,model = "GoogleNyan";
+
+		nvidia,audio-routing =
+			"Headphones", "HPR",
+			"Headphones", "HPL",
+			"Speakers", "SPKR",
+			"Speakers", "SPKL",
+			"Mic Jack", "MICBIAS",
+			"DMICL", "Int Mic",
+			"DMICR", "Int Mic",
+			"IN34", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&acodec>;
+
+		clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
+			 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
+			 <&tegra_car TEGRA124_CLK_EXTERN1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
+		nvidia,mic-det-gpios =
+				<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
+	};
+};
+
+#include "cros-ec-keyboard.dtsi"
-- 
1.9.3




More information about the linux-arm-kernel mailing list