[PATCH v4 08/13] pm: at91: the standby mode uses the same sram function as the suspend to memory mode
Wenyou Yang
wenyou.yang at atmel.com
Tue Jan 27 17:45:28 PST 2015
To simply the PM code, the suspend to standby mode uses the same sram function
as the suspend to memory mode, running in the internal SRAM,
instead of the respective code for each mode.
But for the suspend to standby mode, the master clock doesn't
switch to the slow clock, and the main oscillator doesn't
turn off as well.
Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---
arch/arm/mach-at91/pm.c | 85 +++++++++++++++++--------------------
arch/arm/mach-at91/pm.h | 7 +++
arch/arm/mach-at91/pm_slowclock.S | 18 ++++++++
3 files changed, 64 insertions(+), 46 deletions(-)
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 5010de0..f571109 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -137,62 +137,55 @@ extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0,
void __iomem *ramc1, int memctrl);
extern u32 at91_slow_clock_sz;
+static void at91_pm_suspend(suspend_state_t state)
+{
+ unsigned int pm_data = at91_pm_data.memctrl;
+
+ pm_data |= (state == PM_SUSPEND_MEM) ?
+ AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
+
+ slow_clock(at91_pmc_base, at91_ramc_base[0],
+ at91_ramc_base[1], pm_data);
+}
+
static int at91_pm_enter(suspend_state_t state)
{
at91_pinctrl_gpio_suspend();
switch (state) {
+ /*
+ * Suspend-to-RAM is like STANDBY plus slow clock mode, so
+ * drivers must suspend more deeply, the master clock switches
+ * to the clk32k and turns off the main oscillator
+ */
+ case PM_SUSPEND_MEM:
/*
- * Suspend-to-RAM is like STANDBY plus slow clock mode, so
- * drivers must suspend more deeply: only the master clock
- * controller may be using the main oscillator.
+ * Ensure that clocks are in a valid state.
*/
- case PM_SUSPEND_MEM:
- /*
- * Ensure that clocks are in a valid state.
- */
- if (!at91_pm_verify_clocks())
- goto error;
-
- /*
- * Enter slow clock mode by switching over to clk32k and
- * turning off the main oscillator; reverse on wakeup.
- */
- if (slow_clock) {
- slow_clock(at91_pmc_base, at91_ramc_base[0],
- at91_ramc_base[1],
- at91_pm_data.memctrl);
- break;
- } else {
- pr_info("AT91: PM - no slow clock mode enabled ...\n");
- /* FALLTHROUGH leaving master clock alone */
- }
+ if (!at91_pm_verify_clocks())
+ goto error;
- /*
- * STANDBY mode has *all* drivers suspended; ignores irqs not
- * marked as 'wakeup' event sources; and reduces DRAM power.
- * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and
- * nothing fancy done with main or cpu clocks.
- */
- case PM_SUSPEND_STANDBY:
- /*
- * NOTE: the Wait-for-Interrupt instruction needs to be
- * in icache so no SDRAM accesses are needed until the
- * wakeup IRQ occurs and self-refresh is terminated.
- * For ARM 926 based chips, this requirement is weaker
- * as at91sam9 can access a RAM in self-refresh mode.
- */
- if (at91_pm_standby)
- at91_pm_standby();
- break;
+ at91_pm_suspend(state);
- case PM_SUSPEND_ON:
- cpu_do_idle();
- break;
+ break;
- default:
- pr_debug("AT91: PM - bogus suspend state %d\n", state);
- goto error;
+ /*
+ * STANDBY mode has *all* drivers suspended; ignores irqs not
+ * marked as 'wakeup' event sources; and reduces DRAM power.
+ * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and
+ * nothing fancy done with main or cpu clocks.
+ */
+ case PM_SUSPEND_STANDBY:
+ at91_pm_suspend(state);
+ break;
+
+ case PM_SUSPEND_ON:
+ cpu_do_idle();
+ break;
+
+ default:
+ pr_debug("AT91: PM - bogus suspend state %d\n", state);
+ goto error;
}
error:
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index d2c8996..5bc9c33 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -15,6 +15,13 @@
#include <mach/at91_ramc.h>
+#define AT91_PM_MEMCTRL_MASK 0x0f
+#define AT91_PM_MODE_OFFSET 4
+#define AT91_PM_MODE_MASK 0x0f
+#define AT91_PM_MODE(x) (((x) & AT91_PM_MODE_MASK) << AT91_PM_MODE_OFFSET)
+
+#define AT91_PM_SLOW_CLOCK 0x01
+
#ifdef CONFIG_PM
extern void at91_pm_set_standby(void (*at91_standby)(void));
#else
diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S
index 4e55665..f56d114 100644
--- a/arch/arm/mach-at91/pm_slowclock.S
+++ b/arch/arm/mach-at91/pm_slowclock.S
@@ -16,12 +16,15 @@
#include <mach/hardware.h>
#include <mach/at91_ramc.h>
+#include "pm.h"
+
pmc .req r0
sdramc .req r1
ramc1 .req r2
memctrl .req r3
tmp1 .req r4
tmp2 .req r5
+mode .req r6
/*
* Wait until master clock is ready (after switching master clock source)
@@ -73,6 +76,13 @@ ENTRY(at91_slow_clock)
mov tmp1, #0
mcr p15, 0, tmp1, c7, c10, 4
+ mov tmp1, memctrl
+ mov tmp2, tmp1, lsr#AT91_PM_MODE_OFFSET
+ and mode, tmp2, #AT91_PM_MODE_MASK
+
+ mov tmp1, memctrl
+ and memctrl, tmp1, #AT91_PM_MEMCTRL_MASK
+
cmp memctrl, #AT91_MEMCTRL_MC
bne ddr_sr_enable
@@ -145,6 +155,9 @@ sdr_sr_enable:
str tmp1, [sdramc, #AT91_SDRAMC_LPR]
sdr_sr_done:
+ tst mode, #AT91_PM_SLOW_CLOCK
+ beq skip_disable_main_clock
+
/* Save Master clock setting */
ldr tmp1, [pmc, #AT91_PMC_MCKR]
str tmp1, .saved_mckr
@@ -170,9 +183,13 @@ sdr_sr_done:
bic tmp1, tmp1, #AT91_PMC_MOSCEN
str tmp1, [pmc, #AT91_CKGR_MOR]
+skip_disable_main_clock:
/* Wait for interrupt */
mcr p15, 0, tmp1, c7, c0, 4
+ tst mode, #AT91_PM_SLOW_CLOCK
+ beq skip_enable_main_clock
+
/* Turn on the main oscillator */
ldr tmp1, [pmc, #AT91_CKGR_MOR]
orr tmp1, tmp1, #AT91_PMC_MOSCEN
@@ -200,6 +217,7 @@ sdr_sr_done:
wait_mckrdy
+skip_enable_main_clock:
/*
* at91rm9200 Memory controller
* Do nothing - self-refresh is automatically disabled.
--
1.7.9.5
More information about the linux-arm-kernel
mailing list